USER MANUAL DJM-750-K PIONEER
The Pioneer DJ support site shown above offers FAQs, information on software and various other types of information and services to allow you to use your product in greater comfort.
Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly. After you have finished reading the instructions, put them away in a safe place for future reference.
In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown in the explanatory drawings. However the method of connecting and operating the unit is the same.
If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.
Private households in the member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to designated collection facilities or to a retailer (if you purchase a similar new one).
For countries not mentioned above, please contact your local authorities for the correct method of disposal.
By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.
K058b_A1_En
CAUTION
TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
D3-4-2-1-1_B1_En
WARNING
This equipment is not waterproof. To prevent a fire or shock hazard, do not place any container filled with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain or moisture.
D3-4-2-1-3_A1_En
WARNING
To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the equipment.
D3-4-2-1-7a_A1_En
VENTILATION CAUTION
When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 5 cm at rear, and 3 cm at each side).
WARNING
Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the equipment on thick carpet or a bed.
D3-4-2-1-7b* A1 En
Operating Environment
Operating environment temperature and humidity: +5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH (cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light).
D3-4-2-1-7c*_A2_En
CAUTION
The POWER switch on this unit will not completely shut off all power from the AC outlet. Since the power cord serves as the main disconnect device for the unit, you will need to unplug it from the AC outlet to shut down all power. Therefore, make sure the unit has been installed so that the power cord can be easily unplugged from the AC outlet in case of an accident. To avoid fire hazard, the power cord should also be unplugged from the AC outlet when left unused for a long period of time (for example, when on vacation).
D3-4-2-2-2a*_A1_En
WARNING
Store small parts out of the reach of children and infants. If accidentally swallowed, contact a doctor immediately.
D41-6-4_A1_En
POWER-CORD CAUTION
Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause a fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest PIONEER authorized service center or your dealer for a replacement.
S002* A1 En
Before you start
How to read this manual
Be sure to read both this leaflet and the Operating Instructions contained on the CD-ROM accompanying this product! Both documents include important information that you must understand before using this product.
- In this manual, names of channels and buttons indicated on the product, names of menus in the software, etc., are indicated within square brackets ([]). (e.g. [MASTER] channel, [ON/OFF], [File] menu)
What's in the box
- Driver software/operating instructions CD-ROM
- USB cable
- Power cord
- Warranty card
- Read Before Use (Important)/Quick Start Guide (this document)
Connections
Be sure to turn off the power and unplug the power cord from the power outlet whenever making or changing connections.
Refer to the operating instructions for the component to be connected.
Connect the power cord after all the connections between devices have been completed.
Be sure to use the included power cord.
- To use the fader start function, connect a control cable (page 7).
1 Be sure to use the [MASTER1] terminals only for a balanced output. Connection with an unbalanced input (such as RCA) using an XLR to RCA converter cable (or converter adapter), etc., may lower the sound quality and/or result in noise.
For connection with an unbalanced input (such as RCA), use the [MASTER2] terminals.
2 Be careful not to accidentally insert the power cord of another unit to [MASTER1] terminal.
1 POWER button (page 6)
Turns this unit's power on and off.
2 PHONO terminals
Connect to a phono level (MM cartridge) output device. Do not input line level signals.
To connect a device to the [PHONO] terminals, remove the short-circuit pin plug inserted in the terminals.
Insert this short-circuit pin plug into the [PHONO] terminals when nothing is connected to them to cut external noise.
3 CD/LINE terminals
Connect to a DJ player or a line level output component.
4 SIGNAL GND terminal
Connects an analog player's ground wire here. This helps reduce noise when the analog player is connected.
5 LINE terminals
Connect to a cassette deck or a line level output component.
6 CONTROL terminal
This is a ∅ 3.5 mm mini phone jack type DJ player control terminal. If you connect a Pioneer DJ player using a control cable (supplied with a DJ player), you can start playback of control other operations of the DJ player with the fader of this unit.
7 BOOTH terminals
These are output terminals for a booth monitor.
8 MASTER2 terminals
Connect to a power amplifier, etc.
9 MASTER1 terminals
Connect to a power amplifier, etc.
Be sure to use these as balanced outputs. Be careful not to accidentally insert the power cord of another unit.
10 AC IN
Connects to a power outlet using the included power cord. Wait until all connections between the equipment are completed before connecting the power cord.
Be sure to use the included power cord.
11 MIC terminal (page 7)
Connects a microphone here.
12 USB terminal
Connect the computer.
13 PHONES terminal (page 6)
Connect headphones here.
WARNING
The short-circuit pin plugs out of the reach of children and infants. If accidentally swallowed, contact a doctor immediately.
Operation
1 MIC LEVEL control (page 7)
Adjusts the sound level output from the [MIC] channel.
2 EQ (HI, LOW) controls (page 7)
Adjusts the sound quality of the [MIC] channel.
3 OFF, ON, TALK OVER selector switch (page 7)
Turns the microphone on/off.
4 FADER START (CH-2, CH-3) buttons (page 7)
These turn the fader start function on/off.
5 MONO SPLIT, STEREO selector switch (page 6)
Switches how the monitor sound output from the headphones is distributed.
6 MIXING control (page 6)
This adjusts the monitor volume balance of the sound of channels for which the |CUE| button is pressed and the sound of the |MASTER| channel.
7 LEVEL control (page 6)
Adjusts the sound level output from the headphones.
8 Input selector switches (page 6)
Selects the input source of each channel from the components connected to this unit.
9 Channel Level Indicator (page 6)
Displays the sound level of the respective channels before passing through the channel faders.
10 TRIM control (page 6)
Adjusts the level of audio signals input in each channel.
11 EQ/ISO (HI, MID, LOW) controls (page 6)
These adjust the sound quality of the respective channels.
12 CUE button (page 6)
Presses the [CUE] button(s) for the channel(s) you want to monitor.
13 Channel Fader (page 6)
Adjusts the level of audio signals output in each channel.
14 CROSS FADER ASSIGN (A, THRU, B) selector switch (page 6)
Sets the output destination of each channel to [A] or [B].
15 Crossfader (page 6)
Outputs audio signals assigned by the crossfader assign switch corresponding to the curve characteristics selected by [CROSS FADER] (Crossfader Curve Selector Switch).
16 MASTER LEVEL control (page 6)
Adjusts the audio level output from the [MASTER1] and [MASTER2] terminals.
17 Master Level Indicator (page 6)
Displays the audio level output from the [MASTER1] and [MASTER2] terminals.
18 MONO, STEREO selector switch (page 7)
Switches the sound output from the [MASTER1] terminals, etc., between monaural and stereo.
19 BOOTH MONITOR control (page 7)
Adjusts the level of audio signals output from the [BOOTH] terminal.
20 EQ CURVE (ISOLATOR, EQ) selector switch (page 6)
Switches the function of the [EQ/ISO (HI, MID, LOW)] controls.
21 CH FADER ( , ) selector switch (page 7)
Switches the channel fader's curve characteristics.
22 CROSS FADER ( × , × , × ) selector switch (page 7)
This switches the crossfader curve characteristics.
23 Main unit display
Do not pull on the channel fader and crossfader knobs with excessive force. The knobs have a structure by which they cannot be pulled off easily. Pulling the knobs strongly may result in damaging the unit.
Basic Operation
Outputting sound
1 Press [POWER] button.
Turn on the power of this unit.
2 Switch the input selector switches.
Selects the input sources for the different channels from among the devices connected to this unit.
— [PHONO]: Selects the analog player connected to the [PHONO] terminals.
— [CD/LINE], [LINE]: Selects the DJ player or cassette deck connected to the [CD/LINE] or [LINE] terminals.
— [USB */*]: Selects the sound of the computer connected to the [USB] port.
3 Turn the [TRIM] control.
Adjusts the level of audio signals input in each channel.
The corresponding channel level indicator lights when audio signals are being properly input to that channel.
4 Move the channel fader away from you.
Adjusts the level of audio signals output in each channel.
5 Switch the [CROSS FADER ASSIGN (A, THRU, B)] selector switch.
Switches the output destination of each channel.
— [A]: Assigns to [A] (left) of the crossfader.
— [B]: Assigns to [B] (right) of the crossfader.
— [THRU]: Selects this when you do not want to use the crossfader. (The signals do not pass through the crossfader.)
6 Set the crossfader.
This operation is not necessary when the [CROSS FADER ASSIGN (A, THRU, B)] selector switch is set to [THRU].
7 Turn the [MASTER LEVEL] control.
Audio signals are output from the [MASTER1] and [MASTER2] terminals.
The master level indicator lights.
Adjusting the sound quality
Turn the [EQ/ISO (HI, MID, LOW)] controls for the respective channels.
The adjustable ranges for the respective controls are as shown below.
• HI: -26 dB to +6 dB (13 kHz)
• MID: -26 dB to +6 dB (1 kHz)
- LOW: -26 dB to +6 dB (70 Hz)
❖ Switching the function of the [EQ/ISO (HI, MID, LOW)] controls
Switch the [EQ CURVE (ISOLATOR, EQ)] selector switch.
— [ISOLATOR]: Functions as an isolator.
— [EQ]: The equalizer function is set.
Monitoring sound with headphones
1 Connect headphones to the [PHONES] terminal.
2 Press the [CUE] button(s) for the channel(s) you want to monitor.
3 Switch the [MONO SPLIT, STEREO] selector switch.
— [MONO SPLIT]: The sound of the channels for which the [CUE] button is pressed is output from the headphones output's left channel, the [MASTER] channel sound is output from the right channel.
— [STEREO]: The sound of the channels for which the [CUE] button is pressed is output from the headphones in stereo.
4 Turn the [MIXING] control.
This adjusts the monitor volume balance of the sound of channels for which the [CUE] button is pressed and the sound of the [MASTER] channel.
5 Turn the [LEVEL] control for [HEADPHONES].
The sound of the channels for which the [CUE] button is pressed is output from the headphones.
- When the [CUE] button is pressed again, monitoring is canceled.
Switching the fader curve
Select the channel fader curve characteristics
Switch the [CH FADER (—,)] selector switch.
— [.]: The curve rises suddenly at the back side.
— [√]: The curve rises gradually (the sound gradually increases as the channel fader is moved away from the front side).
Select the crossfader curve characteristics
Switch the [CROSS FADER (×, ×)] selector switch.
— [7] Makes a sharply increasing curve (if the crossfader is moved away from the [A] side, audio signals are immediately output from the [B] side).
— [7] Makes a curve shaped between the two curves above and below.
— [X]: Makes a gradually increasing curve (if the crossfader is moved away from the [A] side, the sound on the [B] side gradually increases, while the sound on the [A] gradually decreases).
Starting playback on a DJ player using the fader (fader start)
If you connect a Pioneer DJ player using a control cable (supplied with a DJ player), you can start playback of control other operations of the DJ player with the fader of this unit.
Connect this unit and Pioneer DJ player beforehand. For instructions on connections, see Connections on page 3.
◆ Start playback using the channel fader
1 Set the [CROSS FADER ASSIGN (A, THRU, B)] selector switch to [THRU].
2 Press one of the [FADER START (CH-2, CH-3)] buttons.
Select the channel to be started with the fader start function.
3 Set the channel fader to the nearest position towards you.
4 Set the cue on the DJ player.
The DJ player pauses playback at the cue point.
5 Move the channel fader away from you.
Playback starts on the DJ player.
- If you set the channel fader back to the original position, the player instantaneously returns to the cue point already set and pauses playback (back cue).
- Start playback using the crossfader
1 Set the [CROSS FADER ASSIGN (A, THRU, B)] selector switch to [A] or [B].
2 Press one of the [FADER START (CH-2, CH-3)] buttons.
Select the channel to be started with the fader start function.
3 Set the crossfader.
Set to the edge opposite the side on which the channel you want to use with the fader start function is set.
4 Set the cue on the DJ player.
The DJ player pauses playback at the cue point.
5 Set the crossfader.
Playback starts on the DJ player.
- If you set the crossfader back to the original position, the player instantaneously returns to the cue point already set and pauses playback (back cue).
Using a microphone
1 Connect the microphone to the [MIC] jack.
2 Set the [OFF, ON, TALK OVER] selector switch to [ON] or [TALK OVER].
— [ON]: The indicator lights.
— [TALK OVER]: The indicator flashes.
- When set to [TALK OVER], the sound of channels other than the [MIC] channel is attenuated by 18 dB (default) when a sound of -10 dB or greater is input to the microphone.
- The audio attenuation level for the [TALK OVER] mode can be changed at the [USER SETUP] screen. For instructions on changing the level, see this product's operating instructions.
- The talk over mode can be switched between the normal mode and the advanced mode. For instructions on changing the mode, see this product's operating instructions.
3 Turn the [MIC LEVEL] control.
Adjust the level of the sound output from the [MIC] channel.
- Pay attention that rotating to the extreme right position outputs a very loud sound.
4 Input audio signals to the microphone.
Adjusting the sound quality
Turn the [MIC] channels' [EQ (HI, LOW)] controls.
The adjustable ranges for the respective controls are as shown below.
• HI: -12 dB to +12 dB (10 kHz)
- LOW: -12 dB to +12 dB (100 Hz)
Switching between monaural and stereo audio
This switches the sound output from the [MASTER1], [MASTER2], [BOOTH], [REC OUT], [PHONES], [DIGITAL MASTER OUT] and [USB] terminals between monaural and stereo.
- To adjust the sound output from the [USB] terminals, select [REC OUT] at [Mixer Audio Output] in the setting utility.
Switch the [MONO, STEREO] selector switch.
— [MONO]: Outputs monaural audio.
— [STEREO]: Outputs stereo audio.
Adjusting the L/R balance of audio
The left/right balance of the sound output from the [MASTER1], [MASTER2], [BOOTH], [REC OUT], [PHONES], [DIGITAL MASTER OUT] and [USB] terminals can be adjusted.
- To adjust the sound output from the [USB] terminals, select [REC OUT] at [Mixer Audio Output] in the setting utility.
1 Set the [MONO, STEREO] selector switch to [STEREO].
2 Turn the [BALANCE] control.
The sound's left/right balance changes according to the direction in which the [BALANCE] control is turned and its position.
- Rotating to the rightmost position outputs only the right sound of stereo audio. Rotating to the leftmost position outputs only the left sound of stereo audio.
Audio is output from the [BOOTH] terminal
Turn the [BOOTH MONITOR] control.
Adjusts the level of audio signals output from the [BOOTH] terminal.
About trademarks and registered trademarks
- Pioneer is a registered trademark of PIONEER CORPORATION.
- Microsoft, Windows and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
- Apple, Macintosh and Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries.
• ASIO is a trademark of Steinberg Media Technologies GmbH.
- The names of companies and products mentioned herein are the trademarks of their respective owners.
Specifications
General
Power requirements ......AC 220 V to 240 V, 50 Hz/60 Hz
Power consumption....32 W
Power consumption (standby) 0.45 W
Main unit weight 7.6 kg
Max. external dimensions .....320 mm (W) × 108 mm (H) × 376 mm (D)
Tolerable operating temperature ....+5 °C to +35 °C
Tolerable operating humidity .... 5 % to 85 % (no condensation)
Audio Section
Sampling rate 96 kHz
MASTER D/A converter 24 bits
Other A/D and D/A converters....24 bits
Frequency characteristic
CD/LINE 20 Hz to 20 kHz
S/N ratio (rated output, A-WEIGHTED)
PHONO....92 dB
CD/LINE....106 dB
MIC 84 dB
Total harmonic distortion (20 kHzBW)
CD/LINE — MASTER1....0.004%
Standard input level / Input impedance
PHONO....-52 dBu/47 kΩ
CD/LINE -12 dBu/47 kΩ
MIC -52 dBu/8.5 kΩ
RETURN....-12 dBu/49 kΩ
Standard output level / Load impedance / Output impedance
MASTER1 +6 dBu/10 kΩ/360 Ω or lower
MASTER2....+2 dBu/10 kΩ/390 Ω or lower
REC OUT ....-8 dBu/10 kΩ/22 Ω or lower
BOOTH....+2 dBu/10 kΩ/390 Ω or lower
SEND -12 dBu/10 kΩ/390 Ω or lower
PHONES +8.5 dBu/32 Ω/10 Ω or lower
Rated output level / Load impedance
MASTER1 +24 dBu/10 kΩ
MASTER2....+20 dBu/10 kΩ
Crosstalk
LINE 82 dB
Channel equalizer characteristic
HI -26 dB to +6 dB (13 kHz)
MID....-26 dB to +6 dB (1 kHz)
LOW -26 dB to +6 dB (70 Hz)
Microphone equalizer characteristic
HI -12 dB to +12 dB (10 kHz)
LOW -12 dB to +12 dB (100 Hz)
PHONO input terminal
RCA pin jack....2 sets
CD/LINE input terminal
RCA pin jacks....4 sets
LINE input terminal
RCA pin jack....2 sets
MIC input terminal
XLR connector/phone jack (∅ 6.3 mm) ....1 set
RETURN Input terminals
Phone jack (∅ 6.3 mm)....1 set
MASTER output terminal
XLR connector....1 set
RCA pin jacks....1 set
BOOTH output terminal
RCA pin jacks....1 set
REC OUT output terminal
RCA pin jacks....1 set
SEND output terminal
Phone jack (∅ 6.3 mm)....1 set
DIGITAL MASTER OUT coaxial output terminal
RCA pin jacks....1 set
PHONES output terminal
Stereo phone jack (∅ 6.3 mm) ....1 set
USB terminal
B type....1 set
CONTROL terminal
Mini phone jack (∅ 3.5 mm)....2 sets
— The specifications and design of this product are subject to change without notice.
— Be sure to use the [MASTER1] terminals only for a balanced output. Connection with an unbalanced input (such as RCA) using an XLR to RCA converter cable (or converter adapter), etc., may lower the sound quality and/or result in noise.
For connection with an unbalanced input (such as RCA), use the [MASTER2] terminals.
• © 2013 PIONEER CORPORATION. All rights reserved.
2 Commandes EQ (HI, LOW) (page 7)
Dimensioni massime....320 mm (L) × 108 mm (A) × 376 mm (P)
WAARSCHUWING NETSNOER
2 Stel de [OFF, ON, TALK OVER] keuzeschakelaar in op [ON] of [TALK OVER].
1 Stel [MONO, STEREO] keuzeschakelaar in op [STEREO].
MID....-26 dB a +6 dB (1 kHz)
LOW -26 dB a +6 dB (70 Hz)
3 Interruptor selector OFF, ON, TALK OVER (página 7)
MID....-26 dB a +6 dB (1 kHz)
LOW -26 dB a +6 dB (70 Hz)
© 2013 PIONEER CORPORATION.
All rights reserved.
© 2013 PIONEER CORPORATION.
