TE 7 - Drill HILTI - Free user manual and instructions

Brand	Hilti
Model	TE 7
Product Type	Rotary hammer
Power consumption	700 W
Supply voltage	230 V ~ 50 Hz
No-load speed	0 – 1050 tr/min
Impact rate	0 – 4500 blows/min
Impact energy	2.2 J
Chuck type	SDS-plus
Max. drilling diameter (concrete)	24 mm
Max. drilling diameter (wood)	30 mm
Max. drilling diameter (metal)	13 mm
Weight	2.5 kg
Dimensions (L x W x H)	366 x 82 x 210 mm
Cable length	4 m
Protection class	II (double insulation)
Operating modes	Drilling, hammer drilling, chiseling
Anti-vibration system	Yes
Safety clutch	Yes
Maintenance and cleaning	Regularly clean the ventilation slots with a dry cloth; have the brushes checked by a professional
Spare parts and repairability	Available from Hilti service; repair by an authorized center recommended

Frequently Asked Questions - TE 7 HILTI

How to change the SDS-plus chuck of the Hilti TE 7?

To change the chuck, pull the ring back and insert the tool while turning slightly until it locks in place. Make sure the tool is securely locked by pulling on it.

What type of oil to use for the Hilti TE 7?

Use a special grease for SDS-plus rotary hammers, such as Hilti grease. Apply a small amount to the tool shank before inserting.

How to set the drilling depth on the TE 7?

Use the depth stop provided. Slide it onto the chuck and set the desired position, then tighten the locking screw.

Can the TE 7 be used for chiseling?

Yes, the TE 7 has a chiseling mode. Turn the mode selector to the chisel symbol (hammer only) and use a suitable chisel.

What to do if the TE 7 no longer starts?

First check the power supply and the cable. If the problem persists, the carbon brushes may be worn. Have them replaced by a professional.

How to clean the air filter of the Hilti TE 7?

The TE 7 does not have a replaceable air filter. Simply clean the air inlets with a dry brush and make sure they are not blocked.

What is the warranty of the Hilti TE 7?

Hilti offers a 2-year warranty on manufacturing defects. Register your product on the Hilti website to benefit from the warranty.

Can you use a regular drill bit with the TE 7?

The TE 7 is designed for SDS-plus bits. To use cylindrical bits, you will need an SDS-plus adapter, but this reduces performance.

How to store the TE 7 safely?

Store the device in its original case, in a dry and frost-free place. Remove the tool from the chuck and clean the device before storage.

What safety precautions to take when using?

Always wear safety glasses and ear protection. Check that the work area does not contain electrical cables or pipes. Use the auxiliary handles.

USER MANUAL TE 7 HILTI

Red and black photo of a red drill bit with visible branding and model number (no text or symbols on the device itself)

1

TE 7 Bohrhammer

Head of BA Quality and Process Mana-

gement

Business Area Electric Tools & Acces-

sories

01/2012

Executive Vice President

Business Unit Power

Tools & Accessories

01/2012

It is essential that the operating instruct are read before the power tool is open the first time.

Always keep these operating instructions get her with the power tool.

Ensure that the operating instructions with the power tool when it is given persons.

Contents Page

1	General information 13
2	Description 14
3	Insert tools, accessories 16
4	Technical data 16
5	Safety instructions 17
6	Before use 19
7	Operation 20
8	Care and maintenance
9	Troubleshooting 22
10	Disposal 22
11	Manufacturer's warranty - tools
12	EC declaration of conformity (original)

1 These numbers refer to the corresponding illustrations. The illustrations can be found on the fold-out cover of pages. Keep these pages open while studying ating instructions. In these operating instructions, the designation “the power tool” always refers to the TE 7 rotary hammer

eOperating controls and parts 1

to other ① Chuck

② Function selector switch
③ On / off switch
④ Forward / reverse switch
⑤ Side handle with depth gauge
⑥ Interface for TE DRS-M dust removal attachment
⑦ Supply cord

21

23

23

1 General information

1.1 Safety notices and their meaning

DANGER

Draws attention to imminent danger that will lead to serious bodily injury or fatality.

WARNING

Draws attention to a potentially dangerous situation could lead to serious personal injury or fatality.

CAUTION

Draws attention to a potentially dangerous situation that could lead to slight personal injury or damage to the equipment or other property.

NOTE

Draws attention to an instruction or other useful information.

1.2 Explanation of the pictograms and other information

Warning signs

General warning

Warning: electricity

Warning: hot surface

Obligation signs

Wear eye protection

Wear a hard hat

Wear ear protection

Wear protective gloves

Wear breathing protection

Symbols

Read the operating instructions before use

Return waste material for recycling.

Drilling without hammering

Hammer drilling

Volts Amps Watts Alternating

current

Hertz
Rated
speed under no load
Revolutions per minute
Diameter

Double insulated
Reverse rotation
Forward rotation

Location of identification

The type designation can tion plate and the serial housing. Make a note of structions and always refer to your Hilti representative

data on the power tool

be found on the type ideal number on the side of the this data in your operating to it when making an end or service department.

Type:

Generation: 02

Serial no.:

2 Description

2.1 Use of the product as directed

The power tool is an electrically-powered rotary hammer with pneumatic hammering mechanism. The power tools are designed for drilling in concrete, masonry, gypsum board (drywall), wood, plastic and metal. Working on materials hazardous to the health (e.g. asbestos) is not permissible.

The power tool is designed for professional use. The power tool may be operated, serviced and repaired only by authorized, trained personnel. This personnel must be informed of any special hazards that may be encountered.

The power tool and its ancillary equipment may present hazards when used incorrectly by untrained personnel or when used not as directed.

The working environment may be as follows: construction site, workshop, renovation, conversion or new construction. The power tool may be operated only when connected to a power supply providing a voltage and frequency in compliance with the information given on its type identification plate.

Changes or modifications to the power tool are not permissible.

To avoid the risk of injury, use only genuine Hilti accessories and insert tools.

Observe the information printed in the operating instructions concerning operation, care and maintenance.

2.2 Chuck

TE-C CLICK chuck

2.3 Switches

Speed control switch for smooth starting.

Function selector switch:

Drilling without hammering

Hammer drilling

Forward / reverse switch (optional)

2.4 Grips

Vibration-absorbing, pivotable side handle with depth gauge Vibration-absorbing grip

2.5 Protective feature

Mechanical slip clutch

2.6 Lubrication

Permanent lubrication (grease)

2.7 Items supplied as standard

1 Power tool
1 TE-C CLICK chuck
1 Side handle with depth gauge
1 Operating instructions
1 Hilti toolbox
1 Cleaning cloth
1 Grease

2.8 Using extension cords

Use only extension cords of a type approved for the application and with conductors of adequate cr power tool may otherwise loose performance and the extension cord may overheat. Check the extension cord for damage at regular intervals. Replace damaged extension cords.

Recommended minimum conductor cross section and max. cable lengths

Conductor cross section	1.5 mm ^2 2.0 mm ^2 2.5 mm ^2 3.5 mm ^2
Mains voltage 100V 40 m 70 m
Mains voltage 110-120 V 30 m 50 m
Mains voltage 220-240 V 60 m 100 m

Do not use extension cords with 1.25 mm ^4 conductor cross section.

2.9 Using extension cords outdoors

When working outdoors, use only extension cords that are approved and correspondingly marked for this application.

2.10 Using a generator or transformer

This power tool may be powered by a generator or transformer which fulfills the following conditions: The unit must provide a power output in watts of at least twice the value printed on the type identification plate on the power tool. The operating voltage must remain within +5% and -15% of the rated voltage at all times, frequency must be in the 50 - 60 Hz range and never above 65 Hz, and the unit must be equipped with automatic voltage regulation and starting boost.

Never operate other power tools or appliances from the generator or transformer at the same time. Switching other power tools or appliances on and off may cause undervoltage and / or overvoltage peaks, resulting in damage to the power tool.

3 Insert tools, accessories

Designation Description

Chuck TE-C Click

Hammer drill bits 4...24 mm

Lightweight percussion core bits 25...68 mm

Multipurpose hole saws 25...68 mm, hexagonal

Anchor-setting tools C-type connection end

Quick-release chuck for wood and metal drill bits For smooth or hex. shank

Key-type chuck For smooth or hex. shank

Wood drill bits 5...20 mm

Metal drill bits 5...13 mm

Metal drill bits / stepped drill bits 5...22 mm

Designation	Short designation	Description
Dust removal attachment	TE DRS-M
Angular chuck		C-type connection end
Angular chuck		TE-AC1
Keyless chuck
Bit holder

4 Technical data

Right of technical changes reserved.

NOTE

The power tool is available in various voltage ratings. Please refer to the power tool's type identification plate for details of its rated voltage and rated input power.

Rated voltage	100 V	110 V	120 V	127 V	220 V	230 V	240 V
Rated power input	670 W	710 W	710 W	710 W	710 W	710 W	710 W
Rated current input	7.2 A	6.9 A	6.3 A	6.0 A	3.4 A	3.3 A	3.2 A
Rated frequency	50/60 Hz	50/60 Hz	60 Hz	60 Hz	50/60 Hz	50/60 Hz	50/60 Hz

Power tool	TE 7
Weight in accordance with EPTA procedure 01/2003	2.9 kg
Dimensions (L x W x H)	320 mm x 75 mm x 215 mm
Speed under no load	0...1,050/min
Hammer drilling speed	860/min
Single impact energy in accordance with EPTA ure 05/2009	proced-

NOTE

The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment

of exposure. The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over the total working period. An estimation of the level vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period. Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of work patterns.

Noise and vibration information (measured in accordance with EN 60745-2-6):

Typical A-weighted sound power level 100 dB (A)

Typical A-weighted emission sound pressure level 89 dB (A)

Uncertainty for the given sound level 3 dB (A)

Triaxial vibration values (vibration vector sum)

Drilling in metal, _HD	4.5 m/s ^2
Hammer drilling in concrete, _HD a	11 m/s ^2
Uncertainty (K) 1.5 m/s ^2

Other information about the power tool

Chuck TE-C Click

Protection class as per EN Protection class II (double insulated)

5 Safety instructions

NOTE

The safety rules in section 5.1 contain all gene rules for power tools which, in accordance with applicable standards, require to be listed in the instructions. Accordingly, some of the rules listed not be relevant to this tool.

5.1 General Power Tool Safety Warnings

a)

WARNING

Read all safety warnings and all instruction to follow the warnings and instructions in electric shock, fire and/or serious injury. warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or operated (cordless) power tool.

5.1.1 Work area safety

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of flam liquids, gases or dust. Power tools create which may ignite the dust or fumes.
c) Keep children and bystanders away while ing a power tool. Distractions can cause control.

5.1.2 Electrical safety

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use

apter plugs with earthed (grounded) power tools eral safety-modified plugs and matching outlets will reduce therisk of electric shock.

b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet co-tions. Water entering a power tool will increase risk of electric shock.

d) Do not abuse the cord. Never use the cord for ns. Fall- may carry, pulling or unplugging the power tool. May result Save keep cord away from heat, oil, sharp edges or all moving parts. Damaged or entangled cords increase the risk of electric shock.

a) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk electric shock.

f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

nable

sparks3 Personal safety

a) Stay alert, watch what you are doing and use operat- common sense when operating a power tool. D ou to lose not use a power tool while you are tired or the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.

any ad-

b) Use personal protective equipment. Always eye protection. Protective equipment such as mask, non-skid safety shoes, hard hat, or protection used for appropriate conditions will personal injuries.
c) Prevent unintentional starting. Ensure the s is in the off-position before connecting to source and/or battery pack, picking up or the tool. Carrying power tools with your fin switch or energising power tools that have on invites accidents.
d) Remove any adjusting key or wrench befo ing the power tool on. A wrench orak tached to a rotating part of the power too in personal injury.
e) Do not overreach. Keep proper footing an ance at all times. This enables better cont power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing jewellery. Keep your hair, clothing and glo away from moving parts. Loose clothes, jev or long hair can be caught in moving part
g) If devices are provided for the connection extraction and collection facilities, ensure t are connected and properly used. Use of collection can reduce dust-related hazards.

5.1.4 Power tool use and care

a) Do not force the power tool. Use the c power tool for your application. The correct tool will do the job better and safer at th which it was designed.
b) Do not use the power tool if the switch turn it on and off. Any power tool that controlled with the switch is dangerous and repaired.
c) Disconnect the plug from the power source and/or the battery pack from the power before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach dren and do not allow persons unfamiliar power tool or these instructions to operate power tool. Power tools are dangerous in of untrained users.
e) Maintain power tools. Check for misalignm binding of moving parts, breakage of part any other condition that may affect the p tool's operation. If damaged, have the pov repaired before use. Many accidents are ca poorly maintained power tools.
f) Keep cutting tools sharp and clean. Proper tained cutting tools with sharp cutting edges likely to bind and are easier to control.
g) Use the power tool, accessories and tool in accordance with these instructions, taking account the working conditions and the w be performed. Use of the power tool for tions different from those intended could res hazardous situation.

wear.5 Service
dust a). Have your power tool serviced by a qualified earing person using only identical replacement parts. reduce This will ensure that the safety of the power too maintained.
witch
power
5.2 Additional safety precautions carrying
ne) switch a) Wear ear protectors. Exposure to noise can cause hearing loss.
re b) Use auxiliary handles, if supplied with the tool. e y left a t - control can cause personal injury.
c) Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring or its ow cord. Cutting accessory contacting a "live" wire m make exposed metal parts of the power tool "liv or and could give the operator an electric shock.
Always hold the power tool securely with both hand on the grips provided. Keep the grips clean and free from oil and grease.
e) Hold power tool by insulated gripping surfaces when performing an operation where the fastene may contact hidden wiring or its own cord. Fa ers contacting a "live" wire may make exposed n parts of the power tool "live" and could give th operator an electric shock.
Correct Breathing protection must be worn if the power tool is used without a dust removal system for work that creates dust.
g) Improve the blood circulation in your fingers by does not relax your hands and exercising your fingers cannot be during breaks between working.
must be avoided touching rotating parts. Switch the power tool on only after bringing it into position at workpiece. Touching rotating parts, especially rotating insert tools, may lead to injury.
i) Always lead the supply cord and extension cord away from the power tool to the rear while working. This helps to avoid tripping over the cord working.
of children must be instructed not to play with t with the power tool.
The power tool is not intended for use by ch hands by debilitated persons or those who have received no instruction or training.
ent dust from material such as paint containing lead, and some wood species, minerals and metal may be power harmful. Contact with or inhalation of the dust may cause allergic reactions and/or respiratory diseases
used by the operator or bystanders. Certain kinds of dry are classified as carcinogenic such as oak and bly main dust especially in conjunction with additives for wood are less conditioning (chromate, wood preservative). Material containing asbestos must only be treated by speci
bits is etc. Where the use of a dust extraction device is going into possible it shall be used. To achieve a high level of work for dust collection, use a suitable vacuum clean opera of the type recommended by Hilti for wood dust and/or mineral dust together with this tool. Ens

ger5.201 Personal safety

that the workplace is well ventilated. The dust mask of filter class P2 is recommer low national requirements for the materials want to work with.

5.2.2 Power tool use and care

a) Secure the workpiece. Use clamps or a secure the workpiece. The workpiece is thus more securely than by hand and both hands free to operate the power tool.
b) Check that the insert tools used are con with the chuck system and that they are in the chuck correctly.
c) Switch the power tool off and unplug the cord in the event of a power failure or in the electric supply. This will prevent acc restarting when the electric power returns.

5.2.3 Electrical safety

a) Before beginning work, check the working (e.g. using a metal detector) to ensure the concealed electric cables or gas and water are present. External metal parts of the po may become live, for example, when an ele is damaged accidentally. This present of electric shock.
b) Check the power tool's supply cord at re intervals and have it replaced by a qualif cialist if found to be damaged. If the po supply cord is damaged it must be repla a specially-prepared supply cord available t Hilti Customer Service. Check extension co at regular intervals and replace them if f be damaged. Do not touch the supply co extension cord if it is damaged while wo Disconnect the supply cord plug from the outlet. Damaged supply cords or extension present a risk of electric shock.

use Dirty aor dusty power tools which have been u ded. frequently for work on conductive materials you should be checked at regular intervals at a Hi Service Center. Under unfavorable circumstances, dampness or dust adhering to the surface of the power tool, especially dust from conductive vice materials, may present a risk of electric shock.

When working outdoors with an electric tool check to ensure that the tool is connected electric supply by way of a ground fault circuit inpatient interrupter (RCD) with a rating of max. 30 mA (tripping current). Use of a ground fault circuit interrupted reduces the risk of electric shock. Use of a ground fault circuit interrupter (RCD supply residual current device) with a maximum tripping current of 30 mA is recommended.

5.2.4 Work area safety

a) Ensure that the workplace is well lit. b) Ensure that the workplace is well ventilated. Exposure to dust at a poorly ventilated workplace n result in damage to the health.
c) There is a risk of injury when the drill bit breath through the object in which the hole is being done. Implement the appropriate safety measures at that near of the object. Parts breaking away could face and/or fall down and injure other persons. Pipes

5.2.5 Personal protective equipment

working user and any other persons in the vicinity m power suitable eye protection, a hard hat, ear prot cards, protective gloves and breathing protection while the tool is in use.

6 Before use

6.1 Fitting the side handle 2

CAUTION

Remove the depth gauge from the side handle to avoid injury.

1. Disconnect the supply cord plug from the outlet.

2. Release the side handle clamping band by turn in the handle counterclockwise.

3. Slide the side handle clamping band over the c and onto the cylindrical section at the front end the power tool.
4. Pivot the side handle into the desired position.
5. CAUTION Check that the clamping band is engaged in the groove provided on the power t secure the side handle by turning the grip clockwise.

6.2 Use of extension cords and generators or transformers

Please refer to the "Description" section.

7 Operation

CAUTION

In the event of the drill bit sticking, the power pivot about its own axis. Always use the power the side handle fitted and hold it securely with so that the resulting opposing force causes the to release in the event of the drill bit sticking or a vicetohold the work pieces securely.

7.1 Preparing for use

7.1.1 Adjusting the depth gauge 3

1. Release the side handle clamping band by the handle counterclockwise.
2. Pivot the side handle into the desired position
3. Adjust the depth gauge to the desired drillin
4. Tighten the side handle securely by turning grip section. This also clamps the depth g position.

7.1.2 Fitting the insert tool 4

CAUTION

Wear protective gloves when changing the insert

1. Disconnect the supply cord plug from the outlet.
2. Check that the connection end of the insert clean and lightly greased. Clean it and gre necessary.
3. Check that the sealing lip of the dust shie and in good condition. Clean the dust shie cessary or replace it if the sealing lip is damaged (please refer to the "Care and ma ance" section).
4. Push the insert tool into the chuck and ro applying slight pressure until it engages in grooves.
5. Push the insert tool further into the chuck heard to engage.
6. Check that the insert tool has engaged con pulling it.

7.1.3 Removing the insert tool 5

CAUTION

Wear protective gloves when changing insert tools as the insert tool will get hot during use.

1. Disconnect the supply cord plug from the power outlet.
2. Open the chuck by pulling back the chuck release sleeve.
3. Pull the insert tool out of the chuck.

7.1.4 Removing the chuck 6

CAUTION

Remove the depth gauge from the side handle and insert tool from the chuck in order to avoid injury.

er1.to disconnect the supply cord plug from the power er too but with
b. o. Pull and the chuck sleeve forward and hold it securely slip clutch 3. Remove the chuck by pulling it away from the Use clamp 1. Use 400

7.1.5 Fitting the chuck 7

CAUTION

Remove the depth gauge from the side handle and insert tool from the chuck in order to avoid injury.

1. Disconnect the supply cord plug from the power outlet.
   Fig.2. Deprin. the Grip the chuck sleeve, pull it forward and hold in securely in this position.
2. Slide the chuck onto the guide tube from the fr and then release the sleeve.
3. Rotate the chuck until it is heard to engage.

7.2 Operation tool.

power

ase it if

CAUTION

d Workieearon the material may cause it to splinter. We'dey of protection and protective gloves. Wear breathing for protection be if no dust removal system is used. Splaining material presents a risk of injury to the eyes body.

late it while

theAuction

The work generates noise. Wear ear protectors. Expc until to isoise can cause hearing loss.

ecty2.by Working at low temperatures

NOTE

The hammering mechanism works only when the pow tool has reached a minimum operating temperature.

Bring the drill bit into contact with the base material and allow the power tool to run under no load un minimum operating temperature is reached. If necessary repeat this procedure until the hammering mechanism begins to operate.

7.2.2 Drilling without hammering 8

1. Turn the function selector switch until it eng the "Drilling without hammering" position. Do operate the function selector switch while th is running.
2. Bring the side handle into the desired position check that it is fitted correctly and secured
3. Plug the supply cord into the power outlet.
4. Position the power tool and drill bit at the where the hole is to be drilled.
5. Press the control switch slowly (drill at a until the drill bit centers itself in the hole)
6. Press the control switch fully to continue of full power.
7. Adjust the pressure applied to the power to cording to the material you are working on ensure the optimum rate of drilling progress

7.2.3 Hammer drilling 8

1. Turn the function selector switch until it engages in the "Hammer drilling" position. Do not operate the "Reverse" function selector switch while the motor is running.

2. Bring the side handle into the desired position and check that it is fitted correctly and secured.

3. Plug the supply cord into the power outlet.
4. Position the power tool and drill bit at the point where the hole is to be drilled.
5. Press the control switch slowly (drill at a low sp on and until the drill bit centers itself in the hole).
6. Press the control switch fully to continue drilling
   pointfull power.
7. Do not apply excessive pressure. This will not increase the power tool's hammering performance.
   Lower pressure extends the life of the insert too 8 Reduce drilling speed shortly before breaking with through inorderto avoid spalling.

pl ac- 7.2.4 Forward / reverse 9 This will

CAUTION

Do not operate the forward / reverse switch while the motor is running.

"Move the forward/reverse switch to the "Forward" or "Reverse" position.

8 Care and maintenance

CAUTION

Disconnect the mains plug from the power

8.1 Care of insert tools

Clean off dirt and dust deposits adhering to the tools and protect them from corrosion by wiping insert tools from time to time with an oil-soaked

8.2 Care of the power tool

CAUTION

Keep the power tool, especially its grip surfac clean and free from oil and grease. Do not ing agents which contain silicone.

The outer casing of the power tool is made resistant plastic. Sections of the grip are made synthetic rubber material.

Never operate the power tool when the ventilati are blocked. Clean the ventilation slots carefully a dry brush. Do not permit foreign objects to interior of the power tool. Clean the outside of tool at regular intervals with a slightly damp cl not use a spray, steam pressure cleaning equip running water for cleaning. This may negatively electrical safety of the power tool.

8.3 Cleaning or replacing the dust shield

outlet Clean the dust shield on the chuck with a dry, clear cloth at regular intervals. Clean the sealing lip by w carefully and then grease it again lightly with Hilti gelt insertessential that the dust shield is replaced if the ringslipthes found to be damaged. Push the tip of a sc eunder: the edge of the dust shield and prise it out the front. Clean the area of the chuck in contact w shield and then fit a new dust shield. Press it in until it engages.

8.4 Maintenance use clean-

WARNING

Repairs to the electrical section of the power tool from a trained out only by trained electrical specialists.

Check all external parts of the power tool for damage or at shogular intervals and check that all controls operate usinglessly. Do not operate the power tool if parts a damage or when the controls do not function fault if thenepesare, the power tool should be repaired by other service.

oment or

affect the 8.5 Checking the power tool after care and maintenance

After carrying out care and maintenance work on the power tool, check that all protective and safety devic are fitted and that they function faultlessly.

9 Troubleshooting

Fault Possible cause Remedy

The power tool doesn't start.	Interruption in the electric supply.	Plug in another electric appliance and check whether it works.
	Supply cord or plug defective.	Have this checked by a trained elec-trical specialist and replaced if necessary.
	Other electrical fault. Have this	checked by a trained elec-trical specialist.
	The carbon brushes are worn.	Have this checked by a trained elec-trical specialist and replaced if necessary.
No hammering action. The power tool is too cold. Allow the power tool to warm up to the minimum operating temperature.See section: 7.2.1 Working at low temperatures

10 Disposal

Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old power tools or appliances for recycling. Please ask your Hilti customer service department or Hilti representative for further information.

For EC countries only

Disposal of electric tools together with household waste is not permissible.

In observance of the European Directive on waste electrical and electronic equipment and its implementation in accordance with national law, electrical appliances that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.

11 Manufacturer's warranty - tools

Hilti warrants that the tool supplied is free of material and workmanship. This warrant as the tool is operated and handled correctly, and serviced properly and in accordance with t Operating Instructions, and the technical system tained. This means that only original Hilti consu components and spare parts may be used in

This warranty provides the free-of-charge repair placement of defective parts only over the entire of the tool. Parts requiring repair or replacement result of normal wear and tear are not covered warranty.

defects in Additional claims are excluded, unless stringent na- tional rules I probit such exclusion. In particular, H cleaned not obligated for direct, indirect, incidental or c ne Haiti sequential damages, losses or expenses in connec- istion with, or by reason of, the use of, or inabilit males, the tool for any purpose. Implied warranties o the tool merchantability or fitness for a particular purp en specifically excluded.

or re-

e Fifesrepair or replacement, send the tool or related p t immediately upon discovery of the defect to the addr d by this local Hilti marketing organization provided.

This constitutes Hilti's entire obligation with regard to warranty and supersedes all prior or contemporaneous comments and oral or written agreements concerning warranties.

12 EC declaration of conformity (original)

Designation: Rotary hammer

Type: TE 7

Generation: 02

Year of design: 2010

We declare, on our sole responsibility, that this complies with the following directives and standards 2006/42/EC, 2004/108/EC, 2011/65/EU, EN 60745-1, EN 60745-2-6, EN ISO 12100.

Hilti Corporation, Feldkircherstrasse 100, FL-9494 Schaan

Paolo Luccini

Head of BA Quality and Process Man-

agement

Business Area Electric Tools & Ac-

cessories

01/2012

Jan Doongaji

Executive Vice President

Business Unit Power

Tools & Accessories

01/2012

Technical documentation filed at:

Perçage sans percussion

7.2.2 Perçage sans percussion 8

Head of BA Quality and Process Management

Business Area Electric Tools & Acces-

sories

01/2012

Jan Doongaji

Executive Vice President

Business Unit Power

Tools & Accessories

01/2012

65/EU Head of BA Quality and Process Management

Business Area Electric Tools & Accessories 01/2012

Jan Doongaji

Executive Vice President

Business Unit Power

Tools & Accessories

01/2012

Head of BA Quality and Process Management Business Area Electric Tools & Accessories 01/2012 Executive Vice President Business Unit Power Tools & Accessories 01/2012

Head of BA Quality and Process Mana-

UE,

gement

Business Area Electric Tools & Acces-

sories

01/2012 01/2012

Executive Vice President

Business Unit Power

Tools & Accessories

Head of BA Quality and Process Management Business Area Electric Tools & Accessories 01/2012 01/2012

Executive Vice President

Business Unit Power Tools & Accessories

7.2.3 Hammerboring 8 Spin-

Head of BA Quality and Process Mana-

'gement

Business Area Electric Tools & Acces-

sories

01/2012 01/2012

Executive Vice President

Business Unit Power

Tools & Accessories

Head of BA Quality and Process Management Executive Vice President Business Area Electric Tools & Accessories Business Unit Power Tools & Accessories 01/2012 01/2012

Teknisk dokumentation vid:

Hastighetsbryter for myk anboring

Funksjonsvelger:

Boring uten slag

Hammerboring

Head of BA Quality and Process

Management

Business Area Electric Tools & Access-

ories

01/2012 01/2012

Executive Vice President

Business Unit Power

Tools & Accessories

Head of BA Quality and Process Management Business Area Electric Tools & Accessories 01/2012 01/2012 Executive Vice President Business Unit Power Tools & Accessories

Head of BA Quality and Process

Management

Business Area Electric Tools &

Accessories

01/2012

Jan Doongaji

Executive Vice President

Business Unit Power

Tools & Accessories

01/2012

Head of BA Quality and Process Ma-

nagement

Business Area Electric Tools &

Accessories

01/2012

Executive Vice President

Business Unit Power

Tools & Accessories

01/2012

mo as 5.1.5 Aptarnavimas

Head of BA Quality and Process Management

Business Area Electric Tools & Accessories

01/2012

Jan Doongaji

Executive Vice President

Business Unit Power

Tools & Accessories

01/2012

Head of BA Quality and Process Mana-

2-0, gement

Business Area Electric Tools & Acces-

sories

01/2012 01/2012

Executive Vice President

Business Unit Power

Tools & Accessories

Tehnilised dokumendid saadaval: