PSE 1200 - Saw METABO - Free user manual and instructions
Find the device manual for free PSE 1200 METABO in PDF.
| Brand | Metabo |
| Model | PSE 1200 |
| Product type | Reciprocating saw |
| Areas of use | Wood, metals, plastics and similar materials (hard rubber, fiberglass laminate) |
| Power supply | Mains, voltage and frequency as per the rating plate |
| Speed adjustment | Continuous via trigger pressure |
| Pendulum motion | Activate/deactivate via rotary knob |
| Blade attachment | Quick-clamping system via clamping sleeve |
| Depth stop | Adjustable longitudinally, fixed by clamping lever |
| Protection class | II |
| Sound level | Can exceed 80 dB(A) - Wear ear protection |
| Vibrations | Measured according to EN 60745, values not specified |
| Maintenance | Regularly clean ventilation slots and clamping device with compressed air; do not oil or grease |
| Main safety instructions | Disconnect before adjustment/maintenance; wear safety glasses, gloves, safety shoes; use dust mask; check for hidden pipes/cables |
| Recommended accessories | Saw blades suited to the material, coolant/lubricant for metals |
| Repairs | By a specialist; contact Metabo representative |
| Environmental protection | Do not dispose of with household waste; recycling according to WEEE directive |
| General information | Manual available in multiple languages on notice-facile.com |
Frequently Asked Questions - PSE 1200 METABO
User questions about PSE 1200 METABO
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Saw in PDF format for free! Find your manual PSE 1200 - METABO and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. PSE 1200 by METABO.
USER MANUAL PSE 1200 METABO
natural_image
Black metal harvesting tool labeled 'metabo' with saw and handle (no additional text or symbols visible)
natural_image
Three sequential images showing a saw tool being cut, with arrows indicating the process (no text or symbols present)
natural_image
Two-panel black-and-white photo showing a person in a diving gear moving water, with no visible text or symbols. | PSE 1200*1) Serial Number: 03824.. | |
| P_1 | W 1200 | |
| P_2 | W 650 | |
| I_(120 V) | A 11.5 | |
| n_0 | min ^-1 (rpm) | 0-2600 |
| I mm (in) 28 (1 1/8) | ||
| m kg (lbs) 4,0 (8.8) | ||
| a_h,CW/K_h,CW | m/s ^2 | 24 / 9,6 |
| L_pA/K_pA | dB (A) 91 / 3 | |
| L_WA/K_WA | dB (A) 102 / 3 | |
*2) 2011/65/EU 2006/42/EC 2004/108/EC
*3) EN 60745
2014-05-02, Volker Siegle
(Director Innovation, Research and Development)
*4) Metabowerke GmbH - Metabo-Allee 1 - 72622 Nuertingen, Germany
A
Original instructions
1. Conformity Declaration
We declare under our sole responsibility: These sabre saws, identified by type and serial number *1), comply with all relevant requirements of the directives *2) and standards *3). Technical file at *4) - see page 3.
2. Specified Use
The sabre saw is suitable for sawing wood, metals, plastics or similar materials such as hard rubber, fibre glass, etc.
In case of use in the area of pallet repair, no claims can be asserted.
The user bears sole responsibility for any damage caused by unspecified use.
Generally accepted accident prevention regulations and the enclosed safety information must be observed.
3. General Safety Instructions
For your own protection and for the protection of your power tool, pay attention to all parts of the text that are marked with this symbol!
WARNING – Reading the operating instructions will reduce the risk of injury.
WARNING Read all safety warnings and instructions. Failure to follow all safety warnings and instructions may result in electric shock, fire and/or serious injury.
Keep all safety instructions and information for future reference.
Pass on your power tool only together with these documents.
4. Special Safety Instructions
Hold the power tool only on the insulated gripping surfaces when performing tasks where the cutting accessory could hit concealed power lines. Cutting accessory contacting a "live" wire may also energise metal parts of the power tool, resulting in an electric shock.
Dust from material such as paint containing lead, some wood species, minerals and metal may be harmful. Contact with or inhalation of the dust may cause allergic reactions and/or respiratory diseases to the operator or bystanders.
Certain kinds of dust are classified as carcinogenic such as oak and beech dust especially in conjunction with additives for wood conditioning (chromate, wood preservative). Material containing asbestos must only be treated by specialists.
- The work place must be well ventilated.
- The use of a dust mask of filter class P2 is recommended.
Follow national requirements for the materials you want to work with.
Pull the plug out of the plug socket before any adjustments or servicing are performed.
Always wear protective goggles, gloves, and sturdy shoes when working with this tool.
Ensure that the spot where you wish to work is free of power cables, gas lines or water pipes (e.g. using a metal detector).
When sawing water pipes, ensure that they do not contain any water.
Wear ear muffs when working for long periods of time. High noise levels over a prolonged period of time may affect your hearing.
Materials that generate dusts or vapours that may be harmful to health (e.g. asbestos) must not be processed.
Do not reach under the workpiece while the machine is in operation.
Do not try to saw extremely small workpieces.
Clamp the workpiece firmly. Under no circumstances should you hold the workpiece with your hand or foot.
Only use sharp, undamaged saw blades. Do not use saw blades that are cracked or that have changed their shape.
For sawing, the guide must make secure contact with the workpiece.
Avoid inadvertent starts: always switch the tool off when the plug is removed from the mains socket or if there has been a power cut.
Always hold the machine with both hands at the intended handles, take a secure stance and concentrate on the work.
Always route the connecting cable away from the tool towards the rear.
Danger of injury due to the sharp saw blade.
Do not touch the moving saw blade! Remove chips and similar material only with the machine at a standstill.
5. Overview
See page 2.
1 Guide
2 Saw blade quick-clamping device
3 Clamping sleeve
4 Clamping lever for securing the guide
5 Forward handle
6 Rotary switch for pendulum action
7 Trigger
8 Rear handle
6. Initial Operation, Setting
Before plugging in, check to see that the rated mains voltage and mains frequency, as stated on the rating label, match your power supply.
Always install an RCD with a max. trip current of 30 mA upstream.
Australia: Always use a residual current device (RCD) protected supply with a rated residual current of 30 mA or less.
6.1 Inserting / replacing the saw blade
Do not touch the saw blade immediately following operation of the tool, as it can be extremely hot and can lead to skin burns.
For access to the saw blade quick-clamping device (2), it must be in its outermost position. If required: press the trigger switch (7) lightly to move the saw blade quick-clamping device into its outermost position.
Pull the mains plug out of the socket.
For access to the saw blade quick-clamping device (2), adjust the guide (1) if required.
1 Turn the clamping sleeve (3) in the direction of the arrow and hold it.
2 Insert the saw blade as far as it will go or remove it.
3 Release the clamping sleeve (3) (the clamping sleeve rotates back to its original position).
4 Check that the saw blade is securely seated.
Note: Should it occur that a saw blade has broken off and it cannot be removed by hand from the saw blade quick-clamping device, turn the clamping sleeve in the direction of the arrow and hold. Engage the tip of a saw blade in the broken section and pull it out. A fine-toothed metal saw blade is best suited for this task. See Fig. A, page 2.
Note: Should it occur that, with the saw blade inserted, the clamping sleeve cannot be turned: move the saw blade upwards and downwards by hand and simultaneously turn the clamping sleeve in the direction of the arrow.
6.2 Setting the guide
The cutting depth can be limited by shifting the guide (1) (e.g. when sawing in front of a wall). Occasionally shift the guide (1) to achieve even wear of the saw blade.
Release the clamping lever (4) and shift the guide (1) along the length of the machine. Secure the guide again using the clamping lever.
Note: If the guide is pulled out too far, the clamping lever cannot be closed and locked for reasons related to safety
Secure the guide firmly using the clamping lever. The clamping lever must lock into place.
6.3 Pendulum action of the saw blade
The pendulum action of the saw blade increases the sawing power (particularly in the case of soft materials such as wood and plastics). Furthermore, the pendulum action reduces the stress applied to the saw blade, as it is raised when emerging from the workpiece.
Use the rotary switch (6) to switch the pendulum action on and off.
Pendulum action ON Pendulum action OFF
For particularly exact sawing cuts and for processing metals: switch off the pendulum action.
7. Use
7.1 Switching on and off
To switch on: press the trigger switch (7). To switch off: let go of the trigger switch (7).
7.2 Stepless stroke rate setting
The stroke rate can be changed steplessly by varying the pressure applied to the trigger switch (7), thus adapting it to the material and working conditions.
7.3 Working Directions
Sawing:
Use a saw blade geared to the material to be sawn.
Depending on the use case, switch the pendulum action on or off.
Press the machine with the guide (1) against the workpiece. Switch on the machine, and only then guide the saw blade against the workpiece.
Do not make contact with any objects or with the ground with the moving saw blade (danger of recoil!)
Adapt the stroke rate to the material to the sawn.
Avoid excessive pressure on the saw blade (particularly in the case of long saw blades).
If the saw blade jams, turn the machine off immediately. Widen the sawn gap slightly with a suitable tool and take out the machine.
After completing the sawing cut, switch off the machine and only take it out of the sawn gap to place it down once the saw blade has come to a standstill (danger of recoil).
Plunge cuts:
Plunge cuts may only be made in soft materials such as wood or plastic. Only use short saw blades.
Hold the machine with both hands at the intended handles, take a secure stance and concentrate on the work.
See Fig. B, page 2. The machine is pressed with the edge of the guide (1) against the workpiece. The saw blade does not make contact with the workpiece. Switch on the machine. The corner of the guide serves as a pivot point around which the machine is slowly aligned, whereby the saw blade cuts into the workpiece.
ENGLISHen
8. Tips and Tricks
To saw tight curves: Use narrow saw blades.
Sawing metal: To increase the life of the saw blades, apply cooling lubricant (cooling lubricant rod 6.23443) along the cutting line.
9. Maintenance
On a regular basis, use compressed air to blow out the machine through the rear ventilation slots.
Regularly clean the saw blade quick-clamping device (2) and blow out with compressed air. Do not oil or grease.
10. Accessories
Use only genuine Metabo accessories.
See page 4.
Use only accessories which fulfil the requirements and specifications listed in these operating instructions.
A) Comprehensive range of saw blades for a wide variety of materials and use cases
For complete range of accessories, see www.metabo.com or the main catalogue.
11. Repairs
Repairs to electrical tools must be carried out by qualified electricians ONLY!
Contact your local Metabo representative if you have Metabo power tools requiring repairs. For addresses see www.metabo.com.
You can download a list of spare parts from www.metabo.com.
12. Environmental Protection
Observe national regulations on environmentally compatible disposal and on the recycling of disused machines, packaging and accessories.
Only for EU countries: Never dispose of power tools in your household waste! In accordance with European Guideline
2002/96/EC on used electronic and electric equipment and its implementation in national legal systems, used power tools must be collected separately and handed in for environmentally compatible recycling.
13. Technical Specifications
Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
m = Weight without mains cable
Measured values determined in conformity with EN 60745.
Machine in protection class II
\~ AC Power
The technical specifications quoted are subject to tolerances (in compliance with the relevant valid standards).
Emission values
These values make it possible to assess the emissions from the power tool and to compare different power tools. Depending on the operating conditions, the condition of the power tool or the accessories, the actual load may be higher or lower. For assessment purposes, please allow for breaks and periods when the load is lower. Based on the adjusted estimates, arrange protective measures for the user e.g. organisational measures.
Vibration total value (vector sum of three directions) determined in accordance with EN 60745:
a_h, CW =Vibration emission value
$$ (S a w i n g \text { in wood }) $$
K_h,CW = Unsafe (vibration)
Typical A-effective perceived sound levels:
L_pA = Sound - pressure level
L_WA = Acoustic power level
K_pA, K_WA = Uncertainty
During operation the noise level can exceed 80 dB(A).
Wear ear protectors!
P_1 =Nominal power input
P_2^ =Power output
I = C u r r e n t
n_0 =Stroke rate at idle speed
s = S t r o k e l e n g t h
Notice originale
K_h, CW = Usikkerhed (vibration)
- Original instructions
- Conformity Declaration
- Specified Use
- General Safety Instructions
- Special Safety Instructions
- Overview
- Initial Operation, Setting
- Inserting / replacing the saw blade
- Setting the guide
- Pendulum action of the saw blade
- Use
- Switching on and off
- Stepless stroke rate setting
- Working Directions
- Sawing:
- Plunge cuts:
- ENGLISHen
- Tips and Tricks
- Maintenance
- Accessories
- Repairs
- Environmental Protection
- Technical Specifications
- Emission values
- Notice originale
Brand : METABO
Model : PSE 1200
Category : Saw