MI-15004 - Office Mount-It! - Free user manual and instructions

USER MANUAL MI-15004 Mount-It!

Line drawing of a simple desk with two legs and a front panel, no text or symbols present

Please scan this QR code to visit the product page

Sit Stand Desk with Drawer

HAVE QUESTIONS?

Monday - Friday from 8:00am - 4:00pm PST

[e-mail]

[phone]

www.mount-it.com

Thank you for choosing Mount-It!

EN

Read the entire instruction manual before you start installation and assembly. If you have any questions regarding any of the instructions or warnings, please contact Mount-It! for assistance.

CAUTION: Use with products heavier than the rated weights indicated may result in instability causing possible injury.
- Please closely follow the assembly instructions. Improper installation may result in damage or serious personal injury. - This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, contact Mount-It! for a replacement.
MAINTENANCE: Check that the product is secure and safe to use at regular intervals (at least every three months).

DE

	Short press the button, the unit will lift 0.39in.(1cm). Long press the button, the unit will continuously lift unless it reaches the highest position of 46.5in. (118 cm) and release the button.
	Short press the button, the unit will lower 0.39in.(1cm). Long press the button, the unit will continuously lower unless it reaches the lowest position of 28.3in. (72cm) and release the button.
	Press up or down button to adjust the unit to your desired position. Press the [S] button and then pressorbutton to save the height.
	Adjust the unit to your seated height and press the [S] button, then pressto save the height.Once complete push thebutton and the unit will automatically move back to the saved position.
	Adjust the unit to your standing height and press the [S] button, then pressto save the height.Once complete push thebutton and the unit will automatically move back to the saved position.
Reset	If the desk is already in lowest position or it encounters any issues and you want to reset, Long pressfor 5 seconds, and the screen will show RES. Keep pressing and the desk will go down to the lowest position and rebound a bit. The reset is complete, and the screen will display the lowest height.Release the button.

Settings
Change Display Height Units	Press and hold the button until a flashing 'S-' is displayed. Press again, and 'Un' is displayed. Press to select it, press or to switch between 'IN' (imperial) and 'SI' (metric), and press to save your choice.
Change Collision Detection Sensitivity	Press and hold the button until a flashing 'S-' is displayed. Press again, and 'Un' is displayed. Press or to switch to 'CF' and press to select it. Press or to switch between off, low, normal, and high sensitivity. Press to save your choice.
RESET	Press and hold the button for 5 seconds, and the screen will show 'RES.' Continue holding until the desk goes down to its lowest level and comes back up slightly.

Protection Mode Error Codes
Hot	Overheating Protection: When the motor has been working continuously for 2 minutes, it will stop operating to prevent damage from overheating. Wait for at least 18 minutes before making any further height adjustment.
E10	Sensor Malfunction Warning: Motor safety sensor can't be detected. Power off, check the connection between the motor and controller, and power back on again.
E20	Overloading Warning: Max load exceeded. If raising the desk, remove objects from the desk to reduce weight and try again. If lowering the desk, power off, take the things off the desk, power back on, and try again.
E02	Operation Status Warning: The desk stops moving if vibration, impact, or incline are detected. If this detection is incorrect, follow the reset instructions before continuing use.
E32	Overvoltage Protection: Input voltage too high. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again.
E31	Undervoltage Protection: Input voltage too low. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again.
E60	Unequal Leg Height Warning: Power off the desk and check whether the left and right legs are at the same height. Power on again and adjust if necessary by following the "RESET" instructions.
-	Cable Disconnection Warning: Check motor and controller cable connections. Normal operation should return once all connectors are properly connected.

PACKAGE CONTENTS

Simple line drawing of a rectangular electronic device with a label on the front panel (no text or symbols on the device itself)

A (x1)
DESKTOP (X1)

B (x1)
RIGHT LEG WITH MOTOR (X1)

C (x1)
LEFT LEG (X1)

D (x1)
TRANSMISSION ROD (X1)

E (x1)
FEET (X2)

F (x1)

POWER CORD (X1)

HARDWARE CONTENTS

a (x8)

M8x16 BOLT

d (x1)
2mm HEX WRENCH

b (x8)

M6x11 BOLT

e (x1)
5mm HEX WRENCH

C (x2)
CABLE MANAGEMENT CLIP

EXTRA PARTS

a (x2)
M8x16 BOLT

b (x2)
M6x11 BOLT

c (x1)
CABLE MANAGEMENT CLIP

Step 1

Assembling the Legs

On a flat and open section of the floor, position the Legs (#B,C) and Desktop (#A) in the configuration shown here.

As shown in magnification bubble, connect the Legs to the Desktop using the

Bolts (#a) and tighten until secure using the 5mm Hex Wrench (#e).

a) and tighten until secure using the 5mm Flex Wrench (#e). B C A e a

Step 2

Attaching the Transmission Rod

Loosen the knob Insert the transmission rod into the hex hole on the left leg and turn the transmission rod counter-clockwise until the left leg goes to the lowest position. Insert the other end of the transmission rod into the slot on the right leg motor. Rotate the rod slightly if needed to properly align. Secure the transmission rod to the slot by tightening the pre-installed set screw using the small Hex wrench (#d). Tighten the knob

Step 3

Attaching the Feet

Attach Feet (#E) to the Leg (#B,C), using Bolts (#b) and tighten until secure using the 5mm Hex Wrench (#e).

Flex Wrench (#C) E e b E

Step 4

Connect the Power Lines

Connect the Power Lines as shown in the image.

Attach the Cable Clip (#c) to the underside of the desktop as needed.

F Cable clip ① ② ③ C

Step 5

Connect the Power

Flip the desk assembly over and connect the Power Cable (#F) to a wall outlet.

Please follow the reset procedure before operating the desk: Press and hold the down button for 5 seconds, and the screen will show "RES". Continue holding until the desk goes down to its lowest level and comes back up slightly

47.2" 23.6" 2.2" 0.7" 28.3" -46.5" 23.6" USB Ports

Power Input 110V-240V

Speed 20 mm/s

Motion Noise <55dB

Load Capability 154 lbs / 70 kg

Warnings

Simple line drawing of a table with a weight symbol and a diagonal line crossing through it, enclosed in a circle (no text or labels)

Do not exceed desk weight limit.

Simple line drawing of a desk with a computer and directional arrows, no text or symbols present.

Keep area of vertical motion free of obstacles.

Prohibition sign showing a table with a weight symbol crossed out by a diagonal line, no text present

Keep weight on desk balanced for correct operation and longer life of components.

Diagram of a table with papers and a diagonal line crossing through it, no text or symbols present

Leave enough slack in cables to allow for full range of vertical motion.

Visit us at www.mount-it.com for product registration and warranty information.

Our US based customer service team is standing by to answer any questions you have about your Mount-It! product.

Available by phone Monday - Friday from 8:00am to 4:00pm PST.

Chat live with an agent on our website!

[e-mail]

[phone]

www.mount-it.com