ISB103 - Pregnant iLive - Free user manual and instructions

USER MANUAL ISB103 iLive

1. Load a MicroSD memory card into the appropriate media port.

2. The speaker will automatically switch to SD mode.

3. Use the controls on the speaker to select and play audio from the connected drive.

SD DC IN

FCC WARNINGS

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

ADDITIONAL WARNINGS

- WARNING: To prevent fire or shock hazards, do not expose this unit to rain or moisture.

- WARNING : Where the mains plug or appliance coupler is used as the disconnect device, such disconnect device shall remain readily operable.

- Lithium batteries, like all rechargeable batteries, are recyclable and should be recycled or disposed of according to state and local guidelines. They should never be disposed of in normal household waste and they should never be incinerated, as they might explode. Contact your local government for disposal or recycling practices in your area.

WARNING : This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to: www.P65Warnings.ca.gov. This product meets and complies with required Federal product guidelines.

International Support

To download this User's Guide in English, Spanish, or French, or to get answers to frequently asked questions, visit the support section at:

www.iLiveElectronics.com

For Warranty Information and the most up-to-date version of this User's Guide, go to: www.iLiveElectronics.com.

Made Green

Protect for Today Sustain for Tomorrow

Specifications are subject to change without notice.

Copyright © 2023 Digital Products International (DPI, Inc.)

All other trademarks appearing herein are the property of their respective owners.

iLIVE™

Exterior view of a modern black and white portable electronic device with a perforated top (no text or symbols visible)

Mini Lit Bluetooth Party Speaker

User's Guide for Model ISB103 v3035

Features

• Bluetooth wireless 5.0: range approximately 60 ft.
• Party + Mode – Pair with another ISB103 speaker
• MicroSD card port
  • Digital volume control
• Voice prompts
  • Built-in rechargeable battery: approximately 6 hrs of playtime at 50% volume
  • USB-C port for battery recharge

Includes

• User's Guide
  • USB-C to USB charging cable

Controls

- 24 I %/M +

1. Microphone
2. Vol -/Previous: Press to decrease volume level. Press and hold to play the previous track.
3. Play/Pair: Press and hold to power on your speaker. Press and hold again to power off your speaker. When on, press once to play or pause music tracks. Press twice to disconnect from Bluetooth device and enter pairing mode. Press three times to activate Party + Mode.
4. Mode/Lights: Press and hold to change source modes to Bluetooth or MicroSD. Press repeatedly to cycle through LED lights modes or turn off lights. Press and hold for 10 seconds to reset the speaker.
5. Volume+/Next: Press to increase volume level. Press and hold to play the next track.

Inputs

SD DC IN MicroSD Slot USB-C Power Input LED Indicator

Voice Prompts

Press both the Vol - and Vol + buttons at the same time to turn voice prompts on or off.

Charging the Battery

To charge the internal battery, plug the USB charging cable into the DC Power Input on the speaker and a powered-on computer or UL certified USB power adaptor (not included) and standard power outlet. Charging time is approximately 90 minutes.

When the battery is low a voice will announce "Low Battery," then the unit will automatically power OFF.

While the unit is charging the Indicator LED will display a solid red light. When the battery is fully charged the light will turn off.

Diagram showing connection between a device and a laptop, with labeled ports and connections to an electrical outlet.

Pairing & Playing Bluetooth Audio

1. When first powered on, the speaker defaults to Bluetooth Mode and is ready to pair automatically. When pairing, remain within 3 feet of the Bluetooth device.
2. Using the controls on your Bluetooth device, select ISB103 in the Bluetooth Settings to pair. If need be, refer to the user's manual for your specific device for more information.
3. When successfully paired, a voice will announce "Connected." The LED Indicator will display a solid blue light. Your Bluetooth device will now be heard through the speaker.
4. Use the controls on the connected Bluetooth device to select and play audio. Use the speaker controls or the connected Bluetooth device to play, pause, and adjust the volume level.
5. After initial pairing, the speaker will automatically connect to the last Bluetooth device used whenever it is in Bluetooth Mode.
6. To disconnect a device, pair with a new device, or if you experience problems connecting to Bluetooth, press the Play button twice. The speaker will re-enter pairing mode and can be paired with a different device.

Party + Mode

1. When powered on, press the 📊/ill button three times on one of your speakers. You will then hear a chime, confirming the speaker is in Party + Pairing Mode.
2. After the speakers connect, a voice will announce "Speaker connected."
3. You can now connect the paired speakers to your Bluetooth device using the standard set up steps.