IG-CL15U - Air purifier SHARP - Free user manual and instructions

USER MANUAL IG-CL15U SHARP

Device of this mark is a trademark of Sharp Corporation.
"Plasmacluster" and "Device of cluster of grapes" are registered trademarks of Sharp Corporation in Japan, USA and elsewhere.

IG-CL15U

Read and keep this manual carefully.
Veuillez lore et conserver ce manuel.
Lea y conserve@cuidadosamente este manual.

Plasmacluster Ion Generator OPERATION MANUAL

FOR CUSTOMER ASSISTANCE(the United States) E-2

CONSUMER LIMITED WARRANTY(the United States) E-3

FOR CUSTOMER ASSISTANCE(Canada) E-4

LIMITED WARRANTY(Canada) E-5

IMPORTANT SAFETY INSTRUCTIONS E-6

• WARNING·
• CAUTIONS CONCERNING OPERATION
• INSTALLATION GUIDELINES
• NOTE

PARTS NAME E-7

• FRONT
• BACK

INSTALLATION POSITION E-8

OPERATION E-8

CLEANING AND MAINTENANCE E-9

• MAIN UNIT E-9
• FILTER
• PLASMACLUSTER ION GENERATING UNIT

PLASMACLUSTER ION GENERATING UNIT REPLACEMENT E-10
- REPLACEMENT OF PLASMACLUSTER ION GENERATING UNIT……E-11

SPECIFICATIONS E-12

TROUBLESHOOTING E-12

• While IG-CL15U can inactivate suspended viruses and other contaminants, it cannot create a completely sterilized environment. SHARP does not guarantee its ability to prevent microbial infection.
• To enable stable emission of high-density Plasmacluster ions, the Plasmacluster Ion Generating Unit mounted in IG-CL15U will need to be replaced periodically*.
• Replacement is required approximately every 2 years (17,500 hours) when operated 24 hours a day. IG-CL15U will stop operating after about 26 months (19,000 hours) if the Plasmacluster Ion Generating Unit is not replaced.

Declaration of Conformity Plasmacluster Ion Generator IG-CL15U This device complies with Part 18 of FCC rules.

Responsible Party: SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07495-1163

Declaration of Conformity Plasmacluster Ion Generator IG-CL15U This ISM device complies with Canadian ICES-001 Responsible Party:

SHARP ELECTRONICS OF CANADA LTD.
335 Britannia Road East Mississauga, Ontario L4Z 1W9 Canada
TEL: [phone]

FOR CUSTOMER ASSISTANCE (the United States)

To aid in answering questions if you call for service or to report loss or theft, please use the space below to record the model and serial number located on the side of the unit.

MODEL NUMBER

SERIAL NUMBER

DATE OF PURCHASE

Dealer Name

Address

City

State

Zip

Telephone

TO PHONE: Dial 1-800-BE-SHARP (237-4277) for:

SERVICE (for your nearest Sharp Authorized Servicer)

PARTS (for your Authorized Parts Distributor)

ACCESSIONS

ADDITIONAL CUSTOMER INFORMATION

TO WRITE: For service problems, warranty information, missing items and other assistance:

Sharp Electronics Corporation

Customer Assistance Center

1300 Naperville Drive

Romeoville, IL 60446-1091

TO ACCESS OUR WEB SITE: www.sharpusa.com

Please provide the following information when you write or call: model number, serial number, date of purchase, your complete mailing address (including zip code), your daytime telephone number (including area code) and description of the problem.

CONSUMER LIMITED WARRANTY

CONSUMER LIMITED WARRANTY FOR U.S. USERS

SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the "Product"), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.

This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor to any Product the exterior of which has been damaged or defaced, which has been subjected to improper voltage or other misuse, abnormal service or handling, or which has been altered or modified in design or construction.

In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide proof of purchase to the servicer.

The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law. ALL IMPLIED WARRANTY INCLUDES THE WARRANTYES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein, or to extend the duration of any warranties beyond the time period described herein on behalf of Sharp.

The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy available to the purchaser. Correction of defects, in the manner and for the period of time described herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or property damage. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

Your Product Model Number & Description:

IG-CL15U Plasmacluster Ion Generator. Be sure to have this information available when you need service for your Product.

Warranty Period for this Product:

One (1) year parts and labor from date of purchase.

Additional Item(s) Excluded From Warranty Coverage:

Appearance items of the Product, filters, accessories, or any printed materials. Product which has been used for rental and/or commercial purposes.

Where to Obtain Service:

From a Sharp Authorized Servicer located in the United States. To find the location of the nearest Sharp Authorized Servicer, call Sharp Toll Free at 1-800-BE-SHARP.

What to Do to Obtain Service:

Ship prepaid or carry in your Product to a Sharp Authorized Servicer. Be sure to have Proof of Purchase available. If you ship the Product, be sure it is insured and packaged securely.

TO OBTAIN SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP, OR VISIT OUR WEBSITE AT www.sharpusa.com

SHARP®

SHARP ELECTRONICS CORPORATION

Sharp Plaza, Mahwah, New Jersey 07495-1163 U.S.A

FOR CUSTOMER ASSISTANCE (Canada)

To aid in answering questions if you call for service or to report loss or theft, please use the space below to record the model and serial number located on the side of the unit.

MODEL NUMBER

SERIAL NUMBER

DATE OF PURCHASE

Dealer Name

Address

City

Province

Postal Code

Telephone

TO PHONE: Dial 1-905-568-7140 for:

SERVICE (for your nearest Sharp Authorized Servicer)

PARTS (for your Authorized Parts Distributor)

ACCESSIONS

ADDITIONAL CUSTOMER INFORMATION

TO WRITE: For service problems, warranty information, missing items and other assistance:

Sharp Electronics of Canada Ltd.

Customer Care

335 Britannia Road East

Mississauga, Ontario L4Z 1W9

TO ACCESS OUR WEB SITE: www.sharp.ca

Please provide the following information when you write or call: model number, serial number, date of purchase, your complete mailing address (including Postal Code), your daytime telephone number (including area code) and description of the problem.

LIMITED WARRANTY

Consumer Electronics Products

Congratulations on your purchase!

Sharp Electronics of Canada Ltd. (hereinafter called "Sharp") gives the following express warranty to the first consumer purchaser for this Sharp brand product, when shipped in its original container and sold or distributed in Canada by Sharp or by an Authorized Sharp Dealer:

Sharp warrants that this product is free, under normal use and maintenance, from any defects in material and workmanship. If any such defects should be found in this product within the applicable warranty period, Sharp shall, at its option, repair or replace the product as specified herein.

This warranty shall not apply to:

(a) Any defects caused or repairs required as a result of abusive operation, negligence, accident, improper installation or inappropriate use as outlined in the owner's manual.
(b) Any Sharp product tampered with, modified, adjusted or repaired by any party other than Sharp, Sharp's Authorized Service Centres or Sharp's Authorized Servicing Dealers.
(c) Damage caused or repairs required as a result of the use with items not specified or approved by Sharp, including but not limited to head cleaning tapes and chemical cleaning agents.
(d) Any replacement of accessories, glassware, consumable or peripheral items required through normal use of the product including but not limited to earphones, remote controls, AC adapters, batteries, temperature probe, stylus, trays, filters, belts, ribbons, cables and paper.
(e) Any cosmetic damage to the surface or exterior that has been defaced or caused by normal wear and tear.
(f) Any damage caused by external or environmental conditions, including but not limited to transmission line/power line voltage or liquid spillage.
(g) Any product received without appropriate model, serial number and CSA/cUL markings.
(h) Any products used for rental or commercial purposes.
(i) Any installation, setup and/or programming charges.

Should this Sharp product fail to operate during the warranty period, warranty service may be obtained upon delivery of the Sharp product together with proof of purchase and a copy of this LIMITED WARRANTY statement to an Authorized Sharp Service Centre or an Authorized Sharp Servicing Dealer. In home warranty service may be provided at Sharp's discretion on any Sharp television with the screen size of 27" or larger and on any Sharp Over-the-Range Microwave Oven.

This warranty constitutes the entire express warranty granted by Sharp and no other dealer, service centre or their agent or employee is authorized to extend, enlarge or transfer this warranty on behalf of Sharp. To the extent the law permits, Sharp disclaims any and all liability for direct or indirect damages or losses or for any incidental, special or consequential damages or loss of profits resulting from a defect in material or workmanship relating to the product, including damages for the loss of time or use of this Sharp product or the loss of information. The purchaser will be responsible for any removal, reinstallation, transportation and insurance costs incurred. Correction of defects, in the manner and period of time described herein, constitute complete fulfillment of all obligations and responsibilities of Sharp to the purchaser with respect to the product and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise.

WARRANTY PERIODS:

Audio Product

Camcorder

DVD Product

Projection

LCD TV

Microwave Oven

Air Purifier

Portable Air Conditioner

Plasmacluster Ion Generator

Parts & Labour (exceptions noted)

1 year
1 year
1 year
1 year (lamp 90 days)
1 year
1 year (magnetron component-4 additional years)
1 year
1 year
1 year

To obtain the name and address of the nearest Authorized Sharp Service Centre or Dealer, please contact:

SHARP ELECTRONICS OF CANADA LTD. 335 Britannia Road East Mississauga, Ontario L4Z 1W9

For more information on this Warranty, Sharp Extended Warranty Offers, Sharp Canada Products, Accessory Sales, Dealer or Service Locations, please call [phone]

Visit our Web site: www.sharp.ca

SERVICE

IMPORTANT SAFETY INSTRUCTIONS

Please read instructions carefully before using IG-CL15U.

When using electrical appliances, basic safety precautions should be followed, including the following:

WARNING - To reduce the risk of electric shock, fire, or injury :

• Use only a 120 volt outlet.
• The Plasmacluster Ion Generator has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit into the outlet, reverse it. If it still does not fit, contact a qualified electrician or service person. Do not alter the plug in any way.
• DO NOT use the unit if the power cord or plug is damaged, or the connection to the wall outlet is loosened.
  Periodically remove dust from the plug.
• DO NOT insert fingers or foreign objects into the air intake or air outlet.
• Always hold the plug and never pull on the cord when removing the power plug. Electric shock and/or fire from short circuit may result.
• DO NOT remove the plug when your hands are wet.
• DO NOT use the unit near gas appliances or fireplaces.
• If the power cord is damaged, it must be replaced by the manufacturer, its service agent, a Sharp Authorized Service Center or similarly qualified person in order to avoid a hazard.
• Be cautious when cleaning the unit.

Strong corrosive cleansers may damage the exterior.

DO NOT operate when using aerosol insecticides or in rooms where there is oily residue, incense, sparks from lit cigarettes, chemical fumes in the air, or in locations where the unit may get wet, such as a bathroom.
- Only Sharp Authorized Service Center should service this Plasmacluster Ion Generator. Contact the nearest Service Center for any problems, adjustments, or repairs.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance.

CAUTIONS CONCERNING OPERATION:

• DO NOT sit on the main unit and do not lean on it, it may cause injury or malfunction.
• DO NOT block the air intake and/or air outlet.
  DO NOT use the unit near or on hot objects, such as stoves or heaters or where it may come into contact with steam.
• Always operate the main unit in an upright position.
• Clean the exterior with a soft cloth only, otherwise the main unit surface may be damaged or cracked.
• Keep the main unit away from water.

INSTALLATION GUIDELINES:

• Avoid using in locations where the unit is exposed to condensation or drastic temperature changes. Appropriate room temperature is between 32 - 95^(0 - 35^) .
• Avoid locations where grease or oily smoke is generated, otherwise the main unit surface may crack as a result.

NOTE - Radio or TV Interference:

If this Plasmacluster Ion Generator may cause interference to radio or television reception, try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the distance between the unit and radio/TV receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This product fulfils the requirement of the International standard CISPR 11.

In conformity with this standard, this product is classified as group 2 class B equipment.

Group 2 means that the equipment intentionally generates radio-frequency in the form of electromagnetic radiation for electro-discharge machining equipment.

Class B equipment means that the equipment suitable to be used in domestic establishments.

PARTS NAME

FRONT

Control Panel

Fan Speed Indicator

LOW

HIGH

BACK

INSTALLATION POSITION

Place the main unit on a smooth, stable surface in a room, and insert the plug into an electrical socket.

Installation Guidance

Leave at least 10cm of clearance behind the unit.

DO NOT USE the below items near the unit.

silicone-containing products*

SPRAY

WAX

PESTICIDES

• Hair care products, cosmetic products, water proof sprays, polish glass cleaner, wipe and wax.

OPERATION

Press the Mode Button to directly turn on the power and select the preferred mode.

CLEANING AND MAINTENANCE

WARNING:

When cleaning the unit, be sure to first unplug the power cord, and never handle the plug with wet hands.

Electric shock and/or bodily injury may occur as a result.

MAIN UNIT

Every month or more often if necessary

Wipe with a dry soft cloth.

Use water and a mild detergent. And then, wipe with a wet cloth. Make sure to dry out the main unit.

FILTER

Every week or more often if necessary

FILTER CLEAN LIGHT lights up after approx. 1 month (approx, 720 hours), when operated 24 hours a day.

1 Remove dust by using a vacuum cleaner.

Remove and rinse in water.

Use a soft sponge if the dirt does not come off easily.

Press the Filter Reset Button for 3 seconds.

The FILTER CLEAN LIGHT will blink twice and go off.

Even if the FILTER CLEAN LIGHT is off, press the Filter Reset Button for 3 seconds after cleaning.

CLEANING AND MAINTENANCE

PLASMACLUSTER ION GENERATING UNIT

Every 6 months or more often if necessary

*When cleaning the Plasmacluster Ion Generating Unit, be sure to turn off the main unit, unplug the power cord, and never handle the plug with wet hands.

See page E-11 for directions on how to remove and install the Plasmacluster Ion Generating Unit when cleaning.

Remove dust of the needle electrode by using the cleaning brush.

*NEVER TOUCH the connector terminal of Plasmacluster Ion Generating Unit.

PLASMACLUSTER ION GENERATING UNIT REPLACEMENT

In order to release Plasmacluster Ion stably, periodical replacement of Plasmacluster Ion Generating Unit is necessary.

The Unit Replacing Light lights up as a reminder for replacement.

Elapsed Time	Display	Message
Approx. 2 years. (Approx. 17,500 hours)	Flashing(red) UNIT	Suggest replacing Plasmacluster Ion Generating Unit.
Approx. 2 years and 2 months. (Approx. 19,000 hours)	Flashing faster(red) UNIT	•Unit stops operation. •Replace the Plasmacluster Ion Generating Unit.

*Usage environment affects the lifetime of the Plasmacluster Ion Generator.
The Plasmacluster Ion Generator may stop operating before estimated lifetime.
In this case, press Mode button again and restart.
If this does not help, replace with a new Plasmacluster Ion Generating Unit.

REPLACEMENT OF PLASMACLUSTER ION GENERATING UNIT

Plasmacluster Ion Generating Unit
Model	IZ-CCL15U

*Before replacing the Plasmacluster Ion Generating Unit, be sure to turn off the main unit, unplug the power cord, and never handle the plug with wet hands.

Remove the filter.

Remove the screw by using a coin with a similar-size coin head or a screwdriver, and the Plasmacluster Ion Generating Unit.

Replace the new Plasmacluster Ion Generating Unit. Fix it into the main unit firmly.

*After replacing the Plasmacluster Ion Generating Unit, fill the replacement date on the Date Label at the side of the main unit.

FILTER INSTALLATION

Push the right side of the filter in order of ① ② , and lock each tab securely.

ATTENTION

The Plasmacluster Ion Generator might not work correctly if filter is not properly attached.

Please dispose the used Plasmacluster Ion Generating Unit according to any local laws and regulations.

-materials-

• Case: Acrylonitrile Butadiene styrene (ABS)
• Unit: Polybtutylene Terephthalate (PBT), Electric parts.

SPECIFICATIONS

Model	IG-CL15U
Power Supply	120V,60Hz
Fan Speed	HIGH	LOW
Power Consumption(W)	17	13
Airflow Volume(CFM)	46(1.3m³/min)	30(0.8m³/min)
Applicable Floor Area(sq.ft) *1	161(15m²)
Ion Density(ions/cm³) *2	25,000	7,000
Cord Length(ft)	6.5(2.0m)
Outer Dimensions(in.)	10^1/2(W)x6^1/8(D)x13(H)
Weight(lbs)	7.3(3.3kg)

1 The applicable floor area for which an emitted airborne ion density of about 25,000 ions/cm³ can be measured at a point near the center of the room (at a height of about 1.2m from the floor), during operation at the HIGH mode when the main unit is placed near a wall. Louvers adjusted to their lowest tilt angle.
2 Ion count per cm³ blown into air at around the center of the room (at a height of about 1.2m from the floor) during operation at each airstream setting when the main unit is placed near the wall. Louvers adjusted to their lowest tilt angle.
- The number of ions will vary according to the room conditions and operation mode.

Standby Power

In order to operate the electrical circuits while the power plug is inserted in the wall socket, this product consumes about 0.4W of standby power.

For energy conservation, unplug the power cord when the unit is not in use.

TROUBLESHOOTING

Before calling for service, please review the TROUBLESHOOTING chart below. The problem may not be a unit malfunction.

Problem	WHAT TO DO
The Plasmacluster Ion Generator does not work.	·Make sure to insert the plug. ·Attach filter properly. (See page E-11)
Flashing (red)——UNIT FILTER	·It's time to replace Plasmacluster Ion Generating Unit. Replace with a new Plasmacluster Ion Generating Unit. (See page E-11)
Flashing (orange)——FILTER	·Plasmacluster lons are not released. Dust may block the filter, clean the filter. (See page E-9) ·Remove dust from the needle electrode. (See page E-10) If the lights are still flashing after cleaning filter, unplug and contact the store you purchased or Sharp service center.
Flashing (blue)——	·Filter is getting dirty. Clean the filter. After cleaning the filter, press Filter Reset Button for 3 seconds. (See page E-9)
Lighting (orange)——UNIT FILTER	·Confirm the Plasmacluster Ion Generating Unit is set in correct position. (See page E-11)
Flashing (blue)——MODE (ON/OFF)	·Failure Unplug the power cord and contact the store you purchased or Sharp service center.
Flashing (red)——UNIT Flashing (orange)——FILTER	·Failure Unplug the power cord and contact the store you purchased or Sharp service center.

TABLE DES MATIÈRES

POUR ASSISTANCE À LA CLIENTÉLE (Canada) F-2

GARANTIE LIMITEE (Canada) F-3

CONSIGNES IMPORTANTES DE SECURITÉ F-4

• AVENTISSEMENT
• MISES EN GARDE RELATIVES AU FONCTIONNEMENT
  GUIDE D'INSTALLATION
• REMARQUE

NOMENCLATURE F-5

AVANT
DOS

POSITION D'INSTALLATION F-6

FONCTIONNEMENT F-6

NETTOYAGE ET ENTRETIEN F-7

• UNITE PRINCIPALE
  F-7
• UNITE GÉNÉRATRICE D'IONS PLASMACLUSTER

REEMPLACEMENT D'UNITE GÉNÉRATRICE D'IONS PLASMACLUSTER…… F-8

• REMPLACEMENT D'UNITE GÉNÉRATRICE D'IONS PLASMACLUSTER ……F-9

CHARACTERISTIQUES F-10

DéPANNAGE F-10

Partie responsible :

SHARP ELECTRONICS CORPORATION Sharp Plaza,

Mahwah, New Jersey 07495-1163

Partie responsible :

SHARP ELECTRONICS OF CANADA LTD.

335 Britannia Road East Mississauga, Ontario L4Z 1W9 Canada

TÉI.: [phone]

POUR ASSISTANCE À LA CLIENTÉLE (Canada)

Sharp Electronics of Canada Ltd.

MISES EN GARDE RELATIVES AU FONCTIONNEMENT

REPLACEMENT D'UNITE GÉNÉRATRICE D'IONS PLASMACLUSTER

REEMPLACEMENT D'UNITE GÉNÉRATRICE D'IONS PLASMACLUSTER

SHARP ELECTRONICS CORPORATION

Sharp Plaza,

Mahwah, New Jersey 07495-1163

SHARP ELECTRONICS CORPORATION

Sharp Plaza, Mahwah,

New Jersey 07495-1163 U.S.A.

SHARP CORPORATION

Osaka, Japan

SHARP®

SHARP ELECTRONICS OF CANADA LTD.

335 Britannia Road East Mississauga,

Ontario L4Z 1W9 Canada

SHARP CORPORATION

Osaka, Japan

SHARP®

IMPORTANT! Please fill out and return within the next 10 days. Register ONLINE at www.sharpusa.com

1. 1. Mr.

2. Mrs.

3. Ms.

. Miss

Initial Last Name

First Name

Street

City

E-mail Address:

1. What was the most important reason for buying this air purifier?

2. Your date of birth: /Year

3. Marital status: 1. Married 2. Single
4. Date of purchase: / / Year
5. Model number:
6. Serial number:
7. Price paid (excluding sales tax): $ .00

8. Where did you purchase this product?

9. Doctor/Pharmacist

recommendation

1. Reduce smoke

2. Reduce pollen dust and
   mite allergens

3. What features most influenced your decision to purchase this product?

4. Plasmacluster technology

5. Design
6. Triple Filtration System
7. □ Washable Filter

8. True HEPA Filter

9. Cleaning Mode Indicator/
   CLEAN-SIGN

10. Filter Replacement
    Schedule

11. Silent Mode

12. What factors most influenced your decision to purchase this product?

13. □ Brand reputation

14. □ Advertisement
    3 Price
15. Specific product feature
16. Style/Appearance
17. Salesperson

recommendation

1. In what room will this product be installed?

2. Adult's bedroom

3. Children's bedroom

4. Living room

5. Friend/Relative
   recommendation

6. Warranty coverage

7. Doctor/Pharmacist

recommendation
0. Other

1. To help us understand our customers' lifestyles, please indicate the interests and activities in which you or your spouse enjoy participating on a regular basis.

Home Life

1. Grandchildren

2. Home Improvement/Do-It
   Yourself

3. Gardening

4. Own a Dog
5. Own a Cat

Leisure

1. Cultural/Art Events
2. □ Avid Book Reading
3. Bible/Devotional Reading
4. Gourmet Cooking/Fine Foods

5. Wines

6. Art/Antique Collecting

7. Stamp/Coin Collecting

8. □ Crafts

9. Sewing/Needlework/K

Travel

1. Airline Club/Frequent Flyer
2. Travel in USA
3. Foreign Travel
4. Cruise Ship Vacations
5. RV Vacations
6. □ Casino Gambling

Investing and Money

1. Shopping by Catalog/

Mail Order

1. Shopping by Internet
2. Use Credit Cards Regularly
3. Donate to Charitable Causes
4. Investments/Money Making
   Opportunities
5. Contests/Sweepstakes

Great Outdoors

1. Hunting/Shooting
   28.□ Fishing

2. □ Camping/Hiking

3. Wildlife/Environmental Issues
   31.Boating/Sailing
   Sports, Fitness & Health

4. Physical Fitness/Exercise

5. Walking for Health
6. Health/Natural Foods
7. Dieting/Weight Control
8. Self-Improvement
9. Golf
10. Biking
11. Snowboarding/Snow skiing
12. NASCAR

th information about activities in which you are involved and less about those in which you are not. Please check here if, for some reason, you would prefer not to participate in this opportunity.

Failure to return this card will not diminish your warranty rights.

Sharp is a registered trademark of Sharp Corporation. All other trademarks are the property of their respective owners.

PRODUCT REGISTRATION DEPARTMENT

Please do not send any products or other correspondence to this address.

If you have comments or suggestions about our product, please write to:

SHARP

Consumer Electronics Group

Sharp Plaza, Mahwah, NJ 07495-1163 U.S.A.

Register online at www.sharpusa.com

CCV01

First-Class

Postage

Required

Post Office will

not deliver

without proper

postage.

SHARP ELECTRONICS CORPORATION

PO BOX 171098

DENVER CO 80217-1098

Protect Your Investment

Register your product for:

Recall Notifications

We contact our customers in case of recall.

Owner Verification

Registration can serve as verification of your ownership in the event of product theft or loss.

Efficient Service

Completing this card will help you obtain more efficient warranty service in case there is a problem with your product.

Don't forget

We know you are busy, but registering is important, quick and easy!

Or register online at www.sharpusa.com