EVO-16T - Fan Evolar - Free user manual and instructions

Product Type	Table Fan
Brand	Evolar
Model	EVO-16T
Blade Size	16 inches (40 cm)
Rated Voltage	220V
Rated Frequency	50 Hz
Input Power	40W
Speed Settings	3 (Low, Medium, High) + Off (0)
Speed Control	Push buttons
Oscillation	Yes, via oscillation button
Tilt Adjustment	Yes, via tilt knob
Overheat Protection	Built-in thermostat with auto cut-off
Assembly Required	Yes (base, blade, grilles)
Housing Material	Plastic (estimated)
Grille Material	Metal mesh
Safety Features	Do not insert objects; unplug before cleaning/moving; keep vents clear
Maintenance	Clean vents with vacuum; wipe exterior with soft cloth; no water inside motor
Power Cord	If damaged, do not use; seek professional repair
Warranty / Support	Refer to www.evolar.nl
Manual Languages	English, Dutch (NL) and more via translation request

Frequently Asked Questions - EVO-16T Evolar

How do I assemble the Evolar EVO-16T fan?

First, click the chassis into the base and screw it from below. Then remove the spinner and plastic nut from the motor shaft. Insert the blade onto the shaft, ensuring the stopper pin clips into the groove, and tighten the spinner counterclockwise. Finally, attach the front guard over the rear guard and push all safety clips into place.

How do I adjust the fan speed?

Use the speed switches on the base. Press the button for the desired speed: 0 for off, 1 for low, 2 for medium, and 3 for high.

How does the oscillation function work?

Press the oscillation button located on top of the motor housing. The fan will start oscillating left and right. Press again to stop oscillation or to lock the head at a desired position.

Can I tilt the fan head?

Yes. Loosen the tilt knob, adjust the fan head to the desired angle, then tighten the knob securely.

What should I do if the fan overheats?

The fan has a built-in thermostat that automatically cuts power if the motor exceeds safe temperature. If this happens, unplug the fan and let it cool down. Check for obstructions and ensure proper ventilation before restarting.

How do I clean the fan?

Always unplug the fan before cleaning. Use a vacuum cleaner to remove dust from the rear vents. Wipe the exterior with a soft cloth dampened with water (not dripping). Do not use abrasive cleaners or allow water to enter the motor housing.

Can I replace the power cord myself?

No. If the power cord is damaged, the fan must not be used. Contact a qualified technician or the supplier for replacement. Never attempt to repair the fan yourself.

What type of power supply does the fan need?

The fan requires a 220V, 50Hz power supply. Ensure your outlet matches these specifications.

Is the Evolar EVO-16T safe to use around children?

The fan should be used with caution. Do not allow children to insert fingers or objects through the grille. Always supervise children near the fan and unplug it when not in use.

Where can I find spare parts or additional support?

Visit www.evolar.nl for available information, parts, and support. If you need a manual in another language, you can request a translation on the product page.

USER MANUAL EVO-16T Evolar

Front view of a white electric fan with mesh grille and base (no visible text or symbols)

Handleiding tafelventilator 16" 40CM:

Elektrische schema:

graph LR
    A["Fuse"] --> B["L"]
    B --> C["Motor"]
    C --> D["Capacitor"]
    D --> E["Black"]
    C --> F["White"]
    C --> G["Red"]
    H["N"] --> I["Ground"]
    style A fill:#f9f,stroke:#333
    style C fill:#ccf,stroke:#333
    style D fill:#cfc,stroke:#333
    style E fill:#fcc,stroke:#333
    style F fill:#cff,stroke:#333
    style G fill:#ffc,stroke:#333
    style H fill:#fff,stroke:#333

Specificatie:

Nominale spanning: 220V

Frequente: 50Hz

Two circular diagrams with grid patterns, one larger and one smaller, labeled 'FIGURES3' (no text or symbols on the diagrams themselves)

GEBRUIKSAANWIJZING

VENTILATORREGELING (AAN/UIT & SNELHEID)

Simple line drawing of a rectangular object with rounded ends, labeled 'FIGURE4' at bottom (no other text or symbols)

ZWENKFUNCITE

KANTELBEDIENING

ONDERHOUD INSTRUCTIES

Front view of a white electric fan with mesh grille and base (no visible text or symbols)

Manual table fan:

Installation and operation Manual

Evolar EVO-16T

User Manual table fan Evolar EVO-16T

(Before use read and save these instructions carefully)

Assemble diagram:

Onderdelenlijst:

1. Front guard
2. Spinner
3. Blade
4. Nut
5. Rear guard
6. Motor
7. Oscillation switch
8. Base
9. Speed switches
10. Chassis

Wiring diagram:

graph TD
    A["Power Source L"] --> B["Blue"]
    A --> C["White"]
    A --> D["Red"]
    E["Capacitor"] --> F["Motor"]
    G["Black"] --> F
    H["N"] --> I["Ground"]
    style F fill:#f9f,stroke:#333
    style I fill:#ccf,stroke:#333

SPECIFICATION:

Rated voltage: 220V

Rated frequency: 50Hz

Input power: 40W

Size Fan: 16" 40CM

Rules for safe operation:

1. Before use read these installation and operation manual carefully
2. Please match the power with the rated voltage and frequency of the fan.
3. Don't insert fingers, pencils or any other objects through the grille when the fan is running.
4. Disconnect always the power when you move the fan.
5. Unplug the power plug before cleaning the fan.

OVER-HEAT PROTECTION FUNCTION:

A thermostat is built in the motor of the fan. The fuse will be automatically cut out when the motor temperature exceeds the limit caused by any accidents. The plastic pieces will be well protected for burning out and distortion.

ASSEMBLY INSTRUCTIONS

BASE AND CHASSIS ASSEMBLY:

1. Remove the base and the chassis from the box
2. Click the chassis in the basis and screw it to the bottom

BLADE AND GRILLES ASSEMBLY:

1. Remove the spinner and the plastic nut from the front side of the motor shaft. Then tighten the plastic nut. (FIGURE 1)

1. Remove the PVC sleeve on the shaft. Insert the ventilation blade into the shaft. Make sure the stopper pin is clipped in to the groove of the blade. Screw the spinner counter clockwise tot tighten the blades. (FIGURE 2)

2. Hold the front guard to make sure that the trademark is level and that the front guard are centred over the rear guard. Then push all the safety clips into their places. (FIGURE 3)

Two circular diagrams with grid patterns, one larger and one smaller, labeled 'FIGURES3' (no text or symbols on diagrams)

OPERATION INSTRUCTIONS

FAN SPEED CONTROLL (ON/OFF & SPEED)

Use the speed switches to switch the fan on and off. Press the switch to turn on the required speed. The fan has four speed positions: 0 = off, 1 = low, 2 = medium, 3 = high (FIGURE 4)

OSCILLATION CONTROL

To make the fan move (oscillation function) press the oscillation button. This button is located at the top of the motor housing. To move the air flow, press the oscillation button. You can click the oscillation button to move the fan to the required position. (FIGURE 5)

TILT CONTROL

Unscrew the till knob, adjust the fan head to the desired angle by holding the fan head, then tighten the knob (FIGURE 6)

Simple line drawing of a rectangular object with rounded ends, labeled 'FIGURE4' at bottom (no other text or symbols)

MAINTENANCE INSTRUCTIONS

The fan requires little maintenance. Do not attempt to repair the fan yourself. If the fan is damaged or damaged, contact the supplier or go to an authorized repair company.

MAINTENANCE:

1. Disconnect the fan from the power supply before cleaning, assembling or disassembling the fan.
2. To ensure adequate air circulation to the motor, keep vents at the rear of the motor housing room dust and dirt free. You can use a vacuum cleaner to clean these vents. Always remove the plug from the power socket before cleaning the fan. Don't dissemble the fan to remove the dust.
3. Wipe the outer ports with a soft cloth soaking. Do not use abrasive detergent or solvents to avoid scratching the surface.
4. Do not allow water or any other liquid in to the motor housing or interior parts.
5. If the power cord is damaged, the fan can not be used at all times. Request a specialist to repair the fan.
6. Never replace parts on the fan.

SUPPORT

All available information and parts can be found on www.evolar.nl