USER MANUAL PSB 600 RE BOSCH
Power Tools Division
70745 Leinfelden-Echterdingen
www.bosch-pt.com
2609002371 (2008.01) O/125
PSB
530 RA | 600 RE | 650 RE | 650 RA
BOSCH
de Originalbetriebsanleitung en Original instructions fr Notice originale es Manual original pt Manual original it Istruzioni originali nl Oorspronkelijke gebruiksaanwijzing da Original brugsanvisning sv Bruksanvisning i original no Original driftsinstruks fi Alkuperäiset ohjeet
el Πρωτότυπο οδηγιών χρήσης tr Orijinal işletme talimatı
Deutsch. 6
English. Page 16
Français. Page 25
Español. 35
Português. 45
Italiano 55
Dutch.. 65
Danish . 74
Swedish. Page 82
Norwegian. 90
Finnish . 98
Greek Page 106
Turkish Page 116
PSB 650 RA
Dr. Egbert Schneider Senior Vice President Engineering
Dr. Eckerhard Strötgen Head of Product Certification
WARNING
Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges and moving parts. Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed.
Use of the power tool for operations different from those intended could result in a hazardous situation.
5) Service
a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
Machine-specific Safety Warnings
Wear hearing protection when using impact drills. The influence of noise can lead to loss of hearing. Always use the auxiliary handle supplied with the machine. Loss of control can cause personal injury. - Use appropriate detectors to determine if utility lines are hidden in the work area or call the local utility company for assistance. Contact with electric lines can lead to fire and electric shock. Damaging a gas line can lead to explosion. Penetrating a water line causes property damage or may cause an electric shock. - Switch off the power tool immediately when the tool insert jams. Be prepared for high reaction torque that can cause kickback. The tool insert jams when:
- the power tool is subject to overload or
- it becomes wedged in the workpiece.
Hold the power tool only by the insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will also make exposed metal parts of the power tool "live" and shock the operator. - When working with the machine, always hold it firmly with both hands and provide for a secure stance. The power tool is guided more secure with both hands. - Secure the workpiece. A workpiece clamped with clamping devices or in a vice is held more secure than by hand. - Keep your workplace clean. Blends of materials are particularly dangerous. Dust from light alloys can burn or explode. Always wait until the machine has come to a complete stop before placing it down. The tool insert can jam and lead to loss of control over the power tool.
- Never use the machine with a damaged cable. Do not touch the damaged cable and pull the mains plug when the cable is damaged while working. Damaged cables increase the risk of an electric shock.
Functional Description
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Intended Use
The machine is intended for impact drilling in brick, concrete and stone as well as for drilling in wood, metal and plastic. Machines with electronic control and right/left rotation are also suitable for screwdriving and thread-cutting.
Product Features
The numbering of the product features refers to the illustration of the machine on the graphics page.
1 Keyless chuck 2 Spindle lock button (PSB 600 RE/PSB 650 RE/PSB 650 RA) 3 "Drilling/Impact Drilling" selector switch 4 Rotation direction indicator (PSB 600 RE/PSB 650 RE/PSB 650 RA) 5 Lock-on button for On/Off switch 6 On/Off switch 7 Thumbwheel for speed preselection (PSB 600 RE/PSB 650 RE/PSB 650 RA) 8 Rotational direction switch 9 Extraction device with dust collector and depth stop 10 Wing bolt for adjustment of auxiliary handle 11 Auxiliary handle 12 Telescopic guide with depth stop scale 13 Set collar for depth stop 14 Release button for dust collector 15 Dust collector*
16 Dust protection ring 17 Locking latch for dust collector 18 Release button for extraction device 19 Filter element (micro filtersystem) * 20 Level indicator of the dust collector 21 Depth stop 22 Button for depth stop adjustment * 23 Universal bit holder 24 Screwdriver bit 25 Front sleeve 26 Rear sleeve 27 Allen key *
The accessories illustrated or described are not included as standard delivery. *Commercially available (not included in the delivery scope)
Measured values determined according to EN 60745.
Typically the A-weighted noise levels of the product are: Sound pressure level 97 dB(A); Sound power level 108 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values (triax vector sum) determined according to EN 60745:
Drilling into metal: Vibration emission value ah = 4.7m / s2 Uncertainty K = 1.5m / s2
Impact drilling into concrete: Vibration emission value ah = 24.2 m/s2 , Uncertainty K = 2.0 m/s2
Screwdriving: Vibration emission value ah < 2.5 m/s2 , Uncertainty K = 1.5 m/s2 .
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of work patterns.
Technical Data
| Impact Drill | | PSB 530 RA | PSB 600 RE | PSB 650 RE | PSB 650 RA |
| Article number | | 3 603 A26 1.. | 3 603 A26 2.. | 3 603 A26 2.. | 3 603 A26 2.. |
| Rated power input | W | 530 | 600 | 650 | 650 |
| Output power | W | 263 | 320 | 338 | 348 |
| No-load speed | rpm | 50-3000 | 50-3000 | 50-3000 | 50-3000 |
| Rated speed | rpm | 2300 | 1900 | 1690 | 1690 |
| Impact rate | bpm | 48000 | 48000 | 48000 | 48000 |
| Rated torque | Nm | 1.0 | 1.5 | 1.9 | 1.9 |
| Torque at max. output power | Nm | 7.5 | 9.0 | 9.0 | 9.0 |
| Speed preselection | | - | ● | ● | ● |
| Right/left rotation | | ● | ● | ● | ● |
| Spindle lock | | - | ● | ● | ● |
| Dust extraction | | ● | - | - | ● |
| Spindle collar dia. | mm | 43 | 43 | 43 | 43 |
| Max. drilling dia. | | | | | |
| - Concrete | mm | 13 | 16 | 16 | 16 |
| - Steel | mm | 10 | 12 | 12 | 12 |
| - Wood | mm | 20 | 30 | 30 | 30 |
| - with extraction device mounted | mm | 13 | 13 | 13 | 13 |
| Chuck clamping range | mm | 2.0-13 | 2.0-13 | 2.0-13 | 2.0-13 |
| Weight according to EPTA-Procedure 01/2003 | | | | | |
| - with extraction device | kg | 1.6 | 1.7 | 1.7 | 1.7 |
| - without extraction device | kg | 1.5 | 1.6 | 1.6 | 1.6 |
| Protection class | | ☐/II | ☐/II | ☐/II | ☐/II |
The values given are valid for nominal voltages [U] of 230/240 V. For lower voltage and models for specific countries, these values can vary. Please observe the article number on the type plate of your machine. The trade names of the individual machines may vary.
We declare under our sole responsibility that the product described under "Technical Data" is in conformity with the following standards or standardization documents: EN 60745 according to the provisions of the directives 2004/108/EC, 98/37/EC (until Dec. 28, 2009), 2006/42/EC (from Dec. 29, 2009 on).
Technical file at: Robert Bosch GmbH, PT/ESC, D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider Senior Vice President Engineering
Dr. Eckerhard Strötgen Head of Product Certification
17.01.2008, Robert Bosch GmbH, Power Tools Division D-70745 Leinfelden-Echterdingen
Assembly
Before any work on the machine itself, pull the mains plug.
Dusts from materials such as lead-containing coatings, some wood types, minerals and metal can be harmful to one's health. Touching or breathing-in the dusts can cause allergic reactions and/or lead to respiratory infections of the user or bystanders. Certain dusts, such as oak or beech dust, are considered as carcinogenic, especially in connection with wood-treatment additives (chromate, wood preservative). Materials containing asbestos may only be worked by specialists.
- Use dust extraction whenever possible.
- Provide for good ventilation of the working place.
- It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the materials to be worked.
- Use the dust/chip extraction only when working concrete, brick and brickwork. Wood or plastic chips can easily lead to clogging. ▸ WARNING Fire hazard! Do not work metallic materials with the extraction device mounted. Hot metal chips can ignite parts of the extraction device.
To achieve optimum extraction results, please observe the following notes:
- Pay attention that the extraction device faces flush against the workpiece or the wall. This also makes drilling at a right angle easier.
- When using the extraction device, always work with the maximum speed. After reaching the desired drilling depth, pull the drill bit out of the drill hole first and then switch off the impact drill.
- Check the condition of the filter element 19 regularly. Replace a damaged filter element immediately.
- The dust protection ring 16 can wear, especially when working with large drill-bit diameters. Replace the dust protection ring when worn/damaged.
Guide the extraction device 9 from the front toward the bottom side of the impact drill. Pay attention that the extraction device 9 faces flush against the casing and that it is locked.
Attach the locking latch 17 or empty the dust collector 15 before placing down the extraction device.
The dust collector 15 is sufficient for approx. 20 drillings with a drilling diameter of 6 mm.
When the extraction force diminishes or when the level indicator 20 is full, the dust collector 15 must be emptied. For this, press on the riffled surface of the release button 14 and take off the dust collector 15.
Empty and clean the dust collector 15. Clean the filter element 19 by gently striking or tapping against it.
Check the filter element 19 for damage and replace it as required.
For this, as an example, pry off the holder of the filter element 19 (①) and change the filter element 19 including the holder (②). When placing on the holder again, make sure that the rubber gasket is inserted.
Reattach the dust collector 15 again and lock it by pressing against the smooth surface of the release button 14.
For removal of the extraction device 9, push the release button 18 to the right or left and pull off the extraction device 9 toward the front.
Auxiliary Handle
Operate your machine only with the auxiliary handle 11.
The auxiliary handle 11 can be set to any position for a secure and low-fatigue working posture.
Turn the wing bolt for adjustment of the auxiliary handle 10 in anticlockwise direction and set the auxiliary handle 11 to the required position. Then tighten the wing bolt 10 again in clockwise direction.
With the extraction device mounted, the drilling depth "X" can be adjusted.
Insert a drill bit into the drill chuck and clamp the drill bit, see section "Changing the Tool", page 21. Rotate the collar for the depth stop 13 upward until it can be moved on the telescopic guide 12. Place the machine, without switching it on, firmly against the surface to be drilled until the drill bit touches the surface.
Read the scale value of the telescopic guide 12 on the collar 13. Add this value to the requested drilling depth X. Slide the collar 13 to the calculated scale value and then rotate the collar 13 downward to lock the determined clearance.
The required drilling depth X can be set with the depth stop 21.
Press the button for the depth stop adjustment 22 and insert the depth stop into the auxiliary handle 11.
The knurled surface of the depth stop 21 must face upward.
Pull out the depth stop until the distance between the tip of the drill bit and the tip of the depth stop corresponds to the desired drilling depth X.
The drill spindle is locked by pressing the spindle lock button 2. This makes quick and easy changing of the tool in the drill chuck possible.
Open the keyless chuck 1 by turning in rotation direction 0, until the tool can be inserted. Insert the tool.
Firmly tighten the collar of the keyless chuck 1 by hand in rotation direction 2 until the locking action ("click") is no longer heard. This automatically locks the chuck.
The locking is released again to remove the tool when the collar is turned in the opposite direction.
Hold the rear sleeve 26 of the keyless chuck 1 tight and turn the front sleeve 25 in rotation direction 0, until the tool can be inserted. Insert the tool.
Hold the rear sleeve 26 of the keyless chuck 1 tight and firmly turn the front sleeve 25 in rotation direction 2 by hand.
When working with screwdriver bits 24, a universal bit holder 23 should always be used. Use only screwdriver bits that fit the screw head.
For driving screws, always position the "Drilling/Impact Drilling" selector switch 3 to the "Drilling" symbol.
Replacing the Drill Chuck
For power tools without spindle lock, the drill chuck must be replaced by an authorized after-sales service agent for Bosch power tools.
Clamp the short end of an Allen key 27 into the keyless chuck 1.
Place the machine on a firm surface, e.g., a workbench. Hold the machine firmly, press the spindle lock button 2, and loosen the keyless chuck 1 by turning the Allen key 27 in rotation direction ①. Loosen a tight keyless chuck by giving the long end of the Allen key 27 a light blow. Remove the Allen key from the keyless chuck and completely unscrew the keyless chuck.
The keyless chuck is mounted in reverse order.
The drill chuck must be tightened with a tightening torque of approx. 6-8 Nm.
Operation
Starting Operation
Observe correct mains voltage! The voltage of the power source must agree with the voltage specified on the nameplate of the machine. Power tools marked with 230 V can also be operated with 220 V.
The rotational direction switch 8 is used to reverse the rotational direction of the machine. However, this is not possible with the On/Off switch 6 actuated.
Right Rotation: For drilling and driving in screws, push the rotational direction switch 8 left to the stop.
PSB 600 RE/PSB 650 RE/PSB 650 RA: Rotation direction indicator 4 indicates the symbol "△".
Left Rotation: For loosening and unscrewing screws and nuts, press the rotational direction switch 8 through to the right stop.
PSB 600 RE/PSB 650 RE/PSB 650 RA: The rotation direction indicator 4 shows the symbol "".
Setting the Operating Mode
Drilling and Screwdriving
Set the selector switch 3 to the "Drilling" symbol.
Impact Drilling
Set the selector switch 3 to the "Impact drilling" symbol.
The selector switch 3 engages noticeably and can also be actuated while the machine is running.
Switching On and Off
To start the machine, press the On/Off switch 6 and keep it depressed.
To lock the pressed On/Off switch 6, press the lock-on button 5.
To switch off the machine, release the On/Off switch 6, or if it is locked with the lock-on button 5, briefly press the On/Off switch 6 and then release it.
Adjusting the Speed/Impact Frequency
The speed/impact rate of the switched-on power tool can be variably adjusted, depending on how far the On/Off switch 6 is pressed.
Light pressure on the On/Off switch 6 results in low speed/impact rate. Further pressure on the switch increases the speed/impact rate.
Preselecting the Speed/Impact Frequency (PSB 600 RE/PSB 650 RE/PSB 650 RA)
With the thumbwheel for speed preselection 7, the required speed/impact frequency can be preselected even during operation.
The required speed/impact frequency depends on the material and the working conditions, and can be determined through practical testing.
Working Advice
Apply the power tool to the screw/nut only when it is switched off. Rotating tool inserts can slip off.
After longer periods of working at low speed, allow the machine to cool down by running it for approx. 3 minutes at maximum speed with no load.
Maintenance and Service
Maintenance and Cleaning
Before any work on the machine itself, pull the mains plug. For safe and proper working, always keep the machine and ventilation slots clean.
If the machine should fail despite the care taken in manufacturing and testing procedures, repair should be carried out by an after-sales service centre for Bosch power tools.
In all correspondence and spare parts order, please always include the 10-digit article number given on the type plate of the machine.
WARNING! Important instructions for connecting a new 3-pin plug to the 2-wire cable.
The wires in the cable are coloured according to the following code:
Do not connect the blue or brown wire to the earth terminal of the plug.
Important: If for any reason the moulded plug is removed from the cable of this power tool, it must be disposed of safely.
After-sales Service and Customer Assistance
Our after-sales service responds to your questions concerning maintenance and repair of your product as well as spare parts. Exploded views and information on spare parts can also be found under:
Our customer consultants answer your questions concerning best buy, application and adjustment of products and accessories.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O.Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 95HJ
Tel. Service: +44 (0844) 736 0109
Fax: +44 (0844) 736 0146
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: +61 (01300) 307 044
Fax: +61 (01300) 307 045
Inside New Zealand:
Phone: +64 (0800) 543 353
Fax: +64 (0800) 428 570
Outside AU and NZ:
Phone: +61 (03) 9541 5555
www.bosch.com.au
Disposal
The machine, accessories and packaging should be sorted for environmental-friendly recycling.
Only for EC countries:
Do not dispose of power tools into household waste!
According to the European Guideline 2002/96/EC for Waste Electrical and Electronic Equipment and its implementation into national law,
power tools that are no longer usable must be collected separately and disposed of in an environmentally correct manner.
Subject to change without notice.
Dr. Egbert Schneider Senior Vice President Engineering
Dr. Eckerhard Strötgen Head of Product Certification
17.01.2008, Robert Bosch GmbH, Power Tools Division D-70745 Leinfelden-Echterdingen
Montage
Robert Bosch (France) S.A.S.
Dr. Egbert Schneider Senior Vice President Engineering
Dr. Eckerhard Strötgen Head of Product Certification
17.01.2008, Robert Bosch GmbH, Power Tools Division D-70745 Leinfelden-Echterdingen
Montaje
Dr. Egbert Schneider Senior Vice President Engineering
Dr. Eckerhard Strötgen Head of Product Certification
i.v. Mojgcu
17.01.2008, Robert Bosch GmbH, Power Tools Division D-70745 Leinfelden-Echterdingen
Assembly
- Before any work on the power tool, pull the mains plug out of the socket.
Dr. Egbert Schneider Senior Vice President Engineering
Dr. Eckerhard Strötgen Head of Product Certification
i.v. Mojgcu
17.01.2008, Robert Bosch GmbH, Power Tools Division D-70745 Leinfelden-Echterdingen
Assembly
Dr. Egbert Schneider Senior Vice President Engineering
Dr. Eckerhard Strötgen Head of Product Certification
i.v. Moju
17.01.2008, Robert Bosch GmbH, Power Tools Division D-70745 Leinfelden-Echterdingen
Assembly
Dr. Egbert Schneider Senior Vice President Engineering
Dr. Eckerhard Strötgen Head of Product Certification
17.01.2008, Robert Bosch GmbH, Power Tools Division D-70745 Leinfelden-Echterdingen
Assembly
Bosch Service Center
Telegrafvej 3
2750 Ballerup
Tel. Service Center: +45 (04489) 8855
Fax: +45 (04489) 87 55
E-Mail: vaerktoej@dk.bosch.com
Disposal
Power tools, accessories, and packaging should be recycled in an environmentally friendly manner.
Dr. Egbert Schneider Senior Vice President Engineering
Dr. Eckerhard Strötgen Head of Product Certification
Assembly
Pull the plug out of the socket before carrying out any work on the power tool.
Dust/Chip Extraction (PSB 530 RA/PSB 650 RA) (see figure A)
Dr. Egbert Schneider Senior Vice President Engineering
Dr. Eckerhard Strötgen Head of Product Certification
Assembly
Dr. Egbert Schneider Senior Vice President Engineering
Dr. Eckerhard Strötgen Head of Product Certification
i.v. Moju
Assembly
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Dr. Egbert Schneider Senior Vice President Engineering
Dr. Eckerhard Strötgen Head of Product Certification
17.01.2008, Robert Bosch GmbH, Power Tools Division D-70745 Leinfelden-Echterdingen
Safety Instructions
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Reference to figures (PSB 530 RA/PSB 650 RA) (see figure A)
Dust from materials such as lead-containing paint, some wood types, minerals and metals can be harmful. Contact with dust and inhalation of dust can cause allergic reactions and/or respiratory diseases of the user or bystanders.
Certain types of dust, e.g. oak or beech dust, are carcinogenic, especially in combination with additives for wood treatment (chromate, wood preservatives). Such work may only be carried out by specialists.
Symbols (see figure H)
The speed adjustment is carried out by following the reverse procedure.
The tool must be set to a torque of approximately 6-8 Nm.
Operation
Starting
The voltage of the power source must match the voltage specified on the nameplate of the power tool. Power tools with a rated voltage of 230 V can also be operated at 220 V.
Changing the tool (see figure I)
The on/off switch for the rotary direction change can be used to change the direction of rotation of the electric tool. However, this is not possible while the ON/OFF switch is activated.
ROTARY DIRECTION CHANGE: To change the direction of rotation, press the rotary direction change switch 8 further.
We reserve the right to make changes.
Dr. Egbert Schneider Senior Vice President Engineering
Dr. Eckerhard Strötgen
Head of Product
Certification
i.v. Moju
17.01.2008, Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Assembly
Bosch San. ve Tic. A.S.
Ahi Evran Cad. No:1 Kat:22
Polaris Plaza
80670 Maslak/Istanbul
Customer Consultant: +90 (0212) 335 06 66
Customer Service Line: +90 (0212) 335 07 52
Liquidation
