Q: How to use the NILOX NXACCARRYCAM action camera?

The NILOX NXACCARRYCAM action camera is a compact HD camera (42 x 19 x 29 mm) designed to capture photos and videos. Here are the steps to use it properly: Before you start Charging: Connect the device via USB-C. The red indicator stays on until the battery is full (200 mAh built-in battery). microSD card: Insert a microSD card (up to 64 GB) to store videos and photos. Turning on and off Press the M button (power button) for 3 seconds to turn the device on or off. Recording videos Press the M button briefly to enter video mode. Press the photo button to start recording. Press again to stop. The video is automatically saved on the SD card in AVI format (720p HD). Taking photos With the microSD card inserted, press the photo button briefly to capture an image. The flash activates automatically and a shutter sound confirms the shot. Additional functions Silent mode: Press the top button briefly to disable sound and flash. Supplementary light: Hold the top button for 3 seconds in video mode to turn the additional light on/off. Filters: Press the bottom button briefly to select different filter effects. Voice recording: Hold the photo button in standby mode to record a voice memo. Important points The device is not waterproof unless a submersion protection is specified. Do not expose it to temperatures above 40 °C. The battery is not removable - only authorized service centers can replace it. You can also use the device in webcam mode: remove the SD card and connect it via USB-C to a computer.

Q: How do I turn on the NILOX Water Board?

To turn on your NILOX Water Board, follow these steps: Place the board in the water Unlock the power button located on the control panel Press the throttle to start the motor Stop: Simply release the throttle to stop. Speed control: Once started, the right throttle increases speed while the left throttle decreases it. Note that the board offers 3 speed levels and always starts in slow mode. Important: Always lock the power button when you are out of the water to prevent accidental activations.

Q: How to start and activate the assistance of the NILOX 30NXEBCLTV1 electric bike?

Initial setup: Make sure the main ON/OFF switch on the battery is in the ON position. Press and hold the LCD screen button for 2.5 seconds to activate it. The screen will display the battery status and available indicators. Activating motor assistance: Assistance is triggered automatically as soon as you start pedaling. The motor requires a full turn of the crankset to engage. The maximum speed with assistance is 25 km/h. Beyond that, the motor stops automatically to comply with regulations. Adjusting the assistance level: Three levels are available: 1 (lowest), 2 (medium), and 3 (maximum). Use the dedicated button on the screen to switch from one level to another. Without a selected level, there is no assistance. Tip: Turn off the main battery switch when you are no longer using the bike to save charge.

Q: What is the battery voltage of the DOC EBIKE X2?

The battery voltage of the DOC EBIKE X2 is 36V . It is a removable lithium-ion battery with a capacity of 10 Ah, providing a range of up to 70 km in eco mode. The battery can be charged directly on the bike or removed for separate charging, with a charging time of 4-6 hours.

Q: Where can I obtain the remote control for the NILOX Foolish Special?

The remote control is included in the box of the NILOX Foolish Special. It is the wireless model (reference A03) that allows you to remotely control video recording, take photos, pause, and activate the laser. It works with a range of up to 5 meters without obstacles . The remote control requires prior synchronization with the camera before first use. Press the buttons on both the camera and the remote control simultaneously for about 3 seconds until you hear a double beep confirming the pairing. This synchronization uses a unique code that prevents interference with other remote controls. If your original remote control is lost or damaged, you can contact Nilox customer service directly, specifying the model NILOX Foolish Special to obtain a compatible replacement remote control (model A03). They will provide the official spare part suitable for your camera. You can also check with specialized retailers of sports camera accessories and video equipment, who sometimes offer compatible Nilox remote controls as replacement spare parts.

Question 1

How do I charge the NILOX NXSWONAIR smartwatch? I have the cable but not the connector.

Accepted Answer

The NILOX NXSWONAIR smartwatch charges via a 5V/1A cable. If you have the cable but lack the connector (magnetic connector), it is usually provided with the watch or available from NILOX support.

To charge correctly:

Connect the 5V/1A cable to the charging port via the magnetic connector
Plug into a suitable power source
Observe the red light flashing during charging
Charging is complete when the light turns green

The device offers a battery life of 25 days under normal use. It is recommended to fully charge the battery (Li-Ion 3.7V 180 mAh) before each use and to avoid leaving the watch plugged in unnecessarily once charged.

Question 2

How to use the NILOX NXACCARRYCAM action camera?

Accepted Answer

The NILOX NXACCARRYCAM action camera is a compact HD camera (42 x 19 x 29 mm) designed to capture photos and videos. Here are the steps to use it properly:

Before you start

Charging: Connect the device via USB-C. The red indicator stays on until the battery is full (200 mAh built-in battery).
microSD card: Insert a microSD card (up to 64 GB) to store videos and photos.

Turning on and off

Press the M button (power button) for 3 seconds to turn the device on or off.

Recording videos

Press the M button briefly to enter video mode.
Press the photo button to start recording.
Press again to stop. The video is automatically saved on the SD card in AVI format (720p HD).

Taking photos

With the microSD card inserted, press the photo button briefly to capture an image.
The flash activates automatically and a shutter sound confirms the shot.

Additional functions

Silent mode: Press the top button briefly to disable sound and flash.
Supplementary light: Hold the top button for 3 seconds in video mode to turn the additional light on/off.
Filters: Press the bottom button briefly to select different filter effects.
Voice recording: Hold the photo button in standby mode to record a voice memo.

Important points

The device is not waterproof unless a submersion protection is specified.
Do not expose it to temperatures above 40 °C.
The battery is not removable - only authorized service centers can replace it.
You can also use the device in webcam mode: remove the SD card and connect it via USB-C to a computer.

Question 3

How do I turn on the NILOX Water Board?

Accepted Answer

To turn on your NILOX Water Board, follow these steps:

Place the board in the water
Unlock the power button located on the control panel
Press the throttle to start the motor

Stop: Simply release the throttle to stop.

Speed control: Once started, the right throttle increases speed while the left throttle decreases it. Note that the board offers 3 speed levels and always starts in slow mode.

Important: Always lock the power button when you are out of the water to prevent accidental activations.

Question 4

How to activate WiFi on the NILOX EVO 360 camera?

Accepted Answer

To activate WiFi on your NILOX EVO 360 camera, follow these steps:

Press the WiFi button located on the top of the camera (WiFi symbol)
A message "Wi-Fi ON" will appear on the screen with the network name and password
WiFi connection details:
- Network name (SSID): EVO 360
- Password: Nilox1234
On your smartphone, go to WiFi settings, search for the network EVO 360, and connect using the provided password
Open the NILOX 360 App to control the camera remotely and view recordings

Once connected, you can control your camera and access videos through the mobile app.

Question 5

How to start and activate the assistance of the NILOX 30NXEBCLTV1 electric bike?

Accepted Answer

Initial setup:

Make sure the main ON/OFF switch on the battery is in the ON position.
Press and hold the LCD screen button for 2.5 seconds to activate it. The screen will display the battery status and available indicators.

Activating motor assistance:

Assistance is triggered automatically as soon as you start pedaling. The motor requires a full turn of the crankset to engage.
The maximum speed with assistance is 25 km/h. Beyond that, the motor stops automatically to comply with regulations.

Adjusting the assistance level:

Three levels are available: 1 (lowest), 2 (medium), and 3 (maximum).
Use the dedicated button on the screen to switch from one level to another. Without a selected level, there is no assistance.

Tip: Turn off the main battery switch when you are no longer using the bike to save charge.

Question 6

What is the battery voltage of the DOC EBIKE X2?

Accepted Answer

The battery voltage of the DOC EBIKE X2 is 36V.

It is a removable lithium-ion battery with a capacity of 10 Ah, providing a range of up to 70 km in eco mode. The battery can be charged directly on the bike or removed for separate charging, with a charging time of 4-6 hours.

Question 7

Where can I obtain the remote control for the NILOX Foolish Special?

Accepted Answer

The remote control is included in the box of the NILOX Foolish Special. It is the wireless model (reference A03) that allows you to remotely control video recording, take photos, pause, and activate the laser. It works with a range of up to 5 meters without obstacles.

The remote control requires prior synchronization with the camera before first use. Press the buttons on both the camera and the remote control simultaneously for about 3 seconds until you hear a double beep confirming the pairing. This synchronization uses a unique code that prevents interference with other remote controls.

If your original remote control is lost or damaged, you can contact Nilox customer service directly, specifying the model NILOX Foolish Special to obtain a compatible replacement remote control (model A03). They will provide the official spare part suitable for your camera.

You can also check with specialized retailers of sports camera accessories and video equipment, who sometimes offer compatible Nilox remote controls as replacement spare parts.

Question 8

How do I turn on my Nilox Mini HD Action Cam if it doesn't turn on?

Accepted Answer

If your Nilox Mini HD Action Cam does not turn on, here are the steps to follow to resolve this issue:

First, check the battery. Make sure the rechargeable battery is properly inserted into the designated compartment. Connect the camera to a computer using the provided USB cable and check the LED indicator: it should light up red while charging. Allow it to charge for at least 2 hours until the indicator turns off, which indicates a full charge. A completely discharged battery may prevent the device from turning on completely.

Properly press the power button. Locate the On/Off button on the side of the camera (button 7 in the diagram). Press and hold this button for exactly 2 seconds until you see the LED indicator light up. A simple quick press will not be sufficient; you really need to hold the pressure for the full 2 seconds.

Ensure the battery and memory card are in place. Before trying to turn on the camera, open the battery cover (item 12 in the diagram) and check that the lithium-polymer battery is properly seated. Also, insert a microSD memory card (compatible up to 32 GB) into the designated slot. The camera may refuse to start if the battery is not detected or if the memory card is not properly positioned.

Test with another compatible battery. If after a full charge and following the power-on procedure the camera still does not turn on, the battery may be defective. If you have access to another compatible battery for this model, try using it to confirm. Note: always follow safety instructions and avoid tampering with the battery to prevent fire hazards.

If after following all these tips your Nilox Mini HD Action Cam still does not turn on, the problem may be a hardware defect or an electronic malfunction. In this case, contact Nilox customer service or the retailer where you purchased the camera for specialized technical assistance or repair.

Question 9

What should I do if my NILOX NXACBIKECAM camcorder turns on but does not display an image and does not allow me to view videos?

Accepted Answer

If your NILOX NXACBIKECAM camcorder turns on but does not display any image and does not allow you to view videos, the problem usually comes from the microSD card or a temporary software malfunction. Here are the solutions to apply in order:

Check the indicator lights. After turning on, carefully observe the indicators. If the switch light and the video/photo light are blinking simultaneously, this indicates a specific problem with the microSD card: it is missing, defective, or its storage space is full (the maximum accepted capacity is 32 GB). In this case, proceed to the next step as a priority.

Check and format the microSD card. Remove the microSD card from the device and firmly reinsert it into its slot. If the problem persists, try with another compatible microSD card. Before any reuse or purchase of a new card, it is essential to format it on your computer to make it compatible with the camcorder. It is recommended to choose a high-speed microSD card to record quality video files (resolution 1920x1080 30fps). Also, check that the card is not full and delete old files if necessary.

Completely restart the device. Press the power button for about 3 seconds to turn off the camcorder. Wait at least 30 seconds (or longer), then turn the device back on by pressing the same button again for 3 seconds. This operation eliminates temporary malfunctions of the internal software.

Check the battery. Ensure that the built-in battery (2500mAh) has sufficient charge. Connect the camcorder to the supplied power adapter to fully charge the device (charging time: 3 hours). During charging, the power indicator blinks; it stays on when the battery is fully charged. You can record videos while charging if necessary.

Access files via USB. Connect the camcorder to your computer with a Type-C USB cable. The device automatically switches to USB disk mode, allowing you to check if video files are present on the microSD card and copy them to your computer for playback. This step helps to identify whether the problem comes from the camera's display screen or the memory card itself.

Update the firmware. If none of the previous solutions worked, check the official Nilox website (www.nilox.com) to see if there is a firmware update available for your model. An update may fix display or playback bugs. Download and install the update by following the manufacturer's instructions.

Contact technical support. If the camcorder turns on but remains without an image after all these steps, it may be a hardware defect. Contact Esprinet customer service (garanzia@esprinet.com or warranty@esprinet.com) providing your proof of purchase or invoice. The problem may be covered by the conventional warranty provided with the device.

User manual NILOX : user manuals and guides in PDF

Models NILOX most viewed

Browse manuals NILOX by appliance type

Recent questions about devices NILOX