Q: How to clean the air vents of the SimpliGlide 330?

The air vents of your SimpliGlide 330 must always be clean to ensure proper cooling of the motor and optimal performance. The best time to clean is right after mowing, when the grass clippings are still fresh. Before any intervention: wait for the blade to come to a complete stop, unplug the mower from the power supply, and put on work gloves for your safety. Cleaning the underside of the mower: Gently tip the mower on its side Remove the accumulated grass clippings using the provided wrench or scraper Clean the blade and the aerator with a soft brush Never use sharp or pointed objects that could damage them Cleaning the top of the mower: Wipe the top with a dry cloth Use a brush to clean the air flow slots and the fan Do not use sharp objects Prohibited products: never use water, water jets (especially high pressure), or chemicals, gasoline, or solvents. These elements can destroy important plastic parts. Regular maintenance of the air vents ensures a longer lifespan and reliable performance of your mower.

Q: How to remove the blade from the FLYMO HT6-70 electric hedge trimmer?

Before you begin: completely unplug the FLYMO HT6-70 hedge trimmer from the electrical outlet and wait a few seconds for the blades to come to a complete stop. Wear thick protective gloves to avoid cuts when handling the sharp blades. Steps to remove the blade: locate the fixing screws that hold the blade in place, usually located on either side of the motor block. Use a suitable Phillips screwdriver to carefully unscrew these fixings. There are usually two to three screws per side. Once the screws are fully removed, hold the blade firmly and gently pull it out by sliding it out of its housing, being careful not to cut yourself on the sharp edges of the blades. Inspection and maintenance: take advantage of the blade removal to carefully inspect the blades and check their wear condition. Clean any grass or sap residues accumulated on the blades using a soft brush or a dry cloth. If the blades are dull, damaged, or show signs of wear, replace them with original parts compatible with the HT6-70 model. Before reassembly: lightly lubricate the blades with a thin layer of machine oil or specialized oil. This maintenance prevents corrosion and maintains cutting efficiency. Ensure that all contact surfaces are clean and free of debris before reassembling the blade. Secure reassembly: reinstall the blade by gently sliding it back into its housing, then screw the fixings back in the reverse order. Tighten the screws firmly but not excessively to avoid damaging the threads. Check that the blade is stable and properly aligned with the motor block before restoring the power supply.

Question 1

How do I adjust the cutting height of the FLYMO Turbo Lite 250 mower?

Accepted Answer

According to the manual for your FLYMO Turbo Lite 250 mower, the cutting height adjustment is done using adjustment washers. Your mower comes with 1 washer already mounted and 2 additional washers as spare parts.

To increase the cutting height, you need to add the additional adjustment washers to the adjustment mechanism. Each washer added progressively increases the cutting height.

Unfortunately, the PDF manual does not provide detailed visual instructions on the exact placement of the washers. For precise instructions:

Refer to the complete PDF manual (80 pages) - the technical diagram pages may illustrate the mechanism
Contact an authorized Husqvarna or FLYMO service center
Check the markings or labels on the chassis of your mower that may indicate height positions

Question 2

Where can I find a replacement handle for the FLYMO HT6-70?

Accepted Answer

Spare Parts Suppliers

The FLYMO HT6-70 electric hedge trimmer uses a standard handle. Here’s where to find it:

Spareka.fr - Specialist in spare parts for garden equipment. Look for compatible references with the HT6-70.
FixPart.fr and EuroSav.eu - General distributors of portable spare parts.
Original Dealer - Contact the store where you purchased your device; they can order original FLYMO parts directly.

Important Advice: Keep your purchase receipt and make sure to note the model reference (HT6-70) before ordering. Original handles ensure better compatibility and durability than generic models.

If you have trouble locating the part, first check the manual provided with your device, which may contain the exact part number compatible with your model.

Question 3

How to clean the air vents of the SimpliGlide 330?

Accepted Answer

The air vents of your SimpliGlide 330 must always be clean to ensure proper cooling of the motor and optimal performance. The best time to clean is right after mowing, when the grass clippings are still fresh.

Before any intervention: wait for the blade to come to a complete stop, unplug the mower from the power supply, and put on work gloves for your safety.

Cleaning the underside of the mower:

Gently tip the mower on its side
Remove the accumulated grass clippings using the provided wrench or scraper
Clean the blade and the aerator with a soft brush
Never use sharp or pointed objects that could damage them

Cleaning the top of the mower:

Wipe the top with a dry cloth
Use a brush to clean the air flow slots and the fan
Do not use sharp objects

Prohibited products: never use water, water jets (especially high pressure), or chemicals, gasoline, or solvents. These elements can destroy important plastic parts. Regular maintenance of the air vents ensures a longer lifespan and reliable performance of your mower.

Question 4

Why won't the engine of the FLYMO Chevron 37VC lawnmower start?

Accepted Answer

If the engine of your FLYMO Chevron 37VC lawnmower won't start, several causes may be behind this problem. Here are the checks and steps to follow to try to resolve this issue:

1. Check the starting procedure

Make sure the lawnmower is plugged into a functioning electrical outlet.
Check that the power cord is in good condition and properly connected.
To start, you must press the safety trigger (often a small safety lever) and the start handle simultaneously (there may be two levers to operate).

2. Check safety and fuses

Ensure that the lawnmower's safety is not activated or blocked.
Check the fuse of the electrical outlet: if it is blown, replace it with a fuse of the same rating.
Make sure the electrical outlet is working by testing it with another device.

3. Other checks

If the lawnmower is equipped with a main switch, ensure it is in the ON position.
Inspect the power cord for any cuts or damage.

4. In case of persistent problems

If despite these checks, the engine still does not start, there may be an internal electrical fault. In this case, it is recommended to unplug the lawnmower and contact a customer service or an authorized repair center for a more thorough inspection.

Question 5

What to do if the FLYMO PAC A SHREDDER garden shredder does not start or does not turn?

Accepted Answer

If your FLYMO PAC A SHREDDER garden shredder does not start or does not turn, several checks are necessary. The most important point is that the locking mechanism (D1) is not firmly in place. Before starting the machine, ensure that the collection box is correctly positioned and that this locking mechanism is securely fastened. The collection box acts as a protection to prevent access to the cutting blades, and the product should never be used without it.

Next, check the power supply: make sure the device is properly plugged into a functional 230 V, 50 Hz outlet, and that the power cord is not damaged. Test the outlet with another device to confirm it is delivering power. Carefully examine the cord for any cuts or damage.

Then proceed to mechanical checks: a jam or an overload of material can block the mechanism. Completely unplug the product from the power outlet, then inspect the inside of the shredder, clean the material entry (G1), and remove any debris or plant material that is stuck. If a branch is blocked, remove it manually. It is normal for the direction of rotation to change automatically in the event of a sudden blockage of the entry.

Once the obstruction is cleared, press the reset button (H1) located on the device. This button resets the overload circuit breaker that has automatically tripped. Wait a few moments before restarting. To start the product, turn the control knob clockwise until the symbol (E1). To stop it, turn counterclockwise until the symbol O (F1).

If after these checks the shredder still does not start or does not function properly, there may be an internal fault: faulty motor, defective electrical wiring, or malfunction of the overload circuit breaker. In this case, contact the authorized after-sales service, especially since your FLYMO PAC A SHREDDER comes with a 2-year warranty covering manufacturing defects.

Question 6

How to remove the blade from the FLYMO HT6-70 electric hedge trimmer?

Accepted Answer

Before you begin: completely unplug the FLYMO HT6-70 hedge trimmer from the electrical outlet and wait a few seconds for the blades to come to a complete stop. Wear thick protective gloves to avoid cuts when handling the sharp blades.

Steps to remove the blade: locate the fixing screws that hold the blade in place, usually located on either side of the motor block. Use a suitable Phillips screwdriver to carefully unscrew these fixings. There are usually two to three screws per side. Once the screws are fully removed, hold the blade firmly and gently pull it out by sliding it out of its housing, being careful not to cut yourself on the sharp edges of the blades.

Inspection and maintenance: take advantage of the blade removal to carefully inspect the blades and check their wear condition. Clean any grass or sap residues accumulated on the blades using a soft brush or a dry cloth. If the blades are dull, damaged, or show signs of wear, replace them with original parts compatible with the HT6-70 model.

Before reassembly: lightly lubricate the blades with a thin layer of machine oil or specialized oil. This maintenance prevents corrosion and maintains cutting efficiency. Ensure that all contact surfaces are clean and free of debris before reassembling the blade.

Secure reassembly: reinstall the blade by gently sliding it back into its housing, then screw the fixings back in the reverse order. Tighten the screws firmly but not excessively to avoid damaging the threads. Check that the blade is stable and properly aligned with the motor block before restoring the power supply.

User manual FLYMO : user manuals and guides in PDF

Models FLYMO most viewed

Browse manuals FLYMO by appliance type

Recent questions about devices FLYMO