Q: How to tune the radio to a station?

The MEDION MD 82157 offers three tuning modes: Manual tuning: Use the UP▲▲ and DOWN▼▼ buttons to manually adjust the frequency to the desired station. Automatic scan: Press and hold the UP▲▲ or DOWN▼▼ button for about 3 seconds to start an automatic search. The receiver will stop on the first station with a sufficient signal. Fine tuning: Press the FINE button for micro-step adjustments. This function does not work in LW band. Press again to return to normal mode. Available frequency bands: FM: 87.0 to 109.0 MHz MW: 522 to 1656 kHz (9 kHz for Europe, 10 kHz for the USA) SW: 5.85 to 17.9 MHz LW: 144 to 299 kHz Optimizing reception: Fully extend the telescopic antenna and orient it for the best reception. For MW and LW bands, rotate the device in all directions to find the best position for the internal antenna.

Question 1

How do I reset my MEDION LIFE P13210 television to factory settings?

Accepted Answer

To reset your MEDION LIFE P13210 to factory settings (especially when moving), access the settings menu of your television. According to most MEDION televisions in this range, you need to:

Press the Menu button on the remote control
Navigate to Settings or Configuration
Look for an option Reset, Reset or Restore default settings
Confirm the operation (note: this will delete your personal preferences)

The PDF of this manual does not contain the exact steps for this specific model. If the reset option is not visible in the Settings menu, refer to the printed guide provided with your device or contact MEDION support.

Question 2

How to pair the MEDION LIFE P66896 (MD 43896) via Bluetooth?

Accepted Answer

The MEDION LIFE P66896 (MD 43896) system is equipped with Bluetooth 5.4. Here’s how to pair it with your smartphone, tablet, or any other compatible device.

Activate Bluetooth mode on the MEDION

Press the MODE button several times until "Bluetooth" appears on the screen.

Pair your external device

Enable Bluetooth in the settings of your smartphone or tablet.
Start a search for available Bluetooth devices.
Select "MEDION MD 43896" from the list of found devices.
A beep confirms that the pairing was successful.

Available controls in Bluetooth mode

OK: start or pause playback.
◀ / ▶: skip to the previous or next track.
VOL + / VOL -: adjust the volume.

For optimal volume, set your smartphone's volume to maximum and then adjust using the buttons on the hifi system. Already paired devices reconnect automatically whenever Bluetooth mode is active.

Question 3

How to tune the radio to a station?

Accepted Answer

The MEDION MD 82157 offers three tuning modes:

Manual tuning: Use the UP▲▲ and DOWN▼▼ buttons to manually adjust the frequency to the desired station.
Automatic scan: Press and hold the UP▲▲ or DOWN▼▼ button for about 3 seconds to start an automatic search. The receiver will stop on the first station with a sufficient signal.
Fine tuning: Press the FINE button for micro-step adjustments. This function does not work in LW band. Press again to return to normal mode.

Available frequency bands:

FM: 87.0 to 109.0 MHz
MW: 522 to 1656 kHz (9 kHz for Europe, 10 kHz for the USA)
SW: 5.85 to 17.9 MHz
LW: 144 to 299 kHz

Optimizing reception: Fully extend the telescopic antenna and orient it for the best reception. For MW and LW bands, rotate the device in all directions to find the best position for the internal antenna.

Question 4

Where is the power socket on the MEDION LifeTab P9514 tablet?

Accepted Answer

The power socket of the MEDION LifeTab P9514 tablet is located on the side of the device. More specifically, you will find a micro-USB port that serves both for charging and data transfer.

To locate it:

Look on the side edges of the tablet, usually at the bottom right or left depending on the orientation.
The micro-USB port is smaller than a standard USB port and has a trapezoidal shape.
Insert the supplied power cable into this port to charge the tablet.

Be sure to use only the recommended charger and cable to avoid any damage to the battery or the tablet.

Question 5

How to update the internet data on the MEDION GOPAL 5.0 GPS?

Accepted Answer

To update the internet data or maps on your MEDION GOPAL 5.0 GPS, follow the steps below:

Steps to update internet data on MEDION GOPAL 5.0

Connect your GPS to a computer: Use a USB cable to connect your MEDION GOPAL 5.0 to your computer.
Install the update software: Download and install the official MEDION update software from the MEDION website if you haven't done so already.
Launch the software: Open the update software. It should automatically detect your connected device.
Check for updates: In the software, select the option to check for available updates, including internet data and maps.
Download and install updates: Follow the on-screen instructions to download and install the latest data on your GPS.
Disconnect your device: Once the update is complete, safely eject your GPS and unplug the USB cable.

This procedure ensures that your MEDION GOPAL 5.0 has the most up-to-date information for optimal navigation.

Question 6

How do I program the MEDION ND 4689 universal remote to turn on my Nasco television?

Accepted Answer

Your MEDION ND 4689 universal remote does not have a dedicated code for Nasco televisions in the provided code list. You need to use the automatic code search method described below.

Before you start: Manually turn on your Nasco television using its power button.

Step 1 - Activating the search Press and hold the SET button for about 3 seconds until the LED indicator stays on continuously. Then release the SET button.

Step 2 - Selecting the device type Briefly press the TV button to indicate that you are programming a television. The LED indicator should blink briefly.

Step 3 - Starting the automatic search Point the remote at your Nasco television and briefly press the CHAN+ (next channel) button once. The remote will then automatically send the codes one after the other, about one code per second. You will see the LED indicator light up with each code sent. You can also use the POWER or PLAY button if the CHAN+ button does not work.

Step 4 - Validating the code As soon as your Nasco television responds to the remote (turns on, off, changes channel, etc.), immediately press the OK button to store this code. The code will be saved.

Practical tip: If the search is too fast and you do not have enough time to test each code, you can slow down the process (one code every 3 seconds instead of one second) by pressing twice briefly on the CHAN+ button in step 3. About 350 codes are pre-programmed in this remote, so your Nasco television code should be found automatically even if it is not listed among the brands.

User manual MEDION : user manuals and guides in PDF

Models MEDION most viewed

Browse manuals MEDION by appliance type

Recent questions about devices MEDION