R7060 - Programator irigare WOOX - Manual de utilizare gratuit

Tip produs	Programator de udare
Marcă	WOOX
Model	R7060
Alimentare	2 baterii AA (nu sunt incluse)
Racord intrare	Femelă 3/4" cu inel O
Racord ieșire	Mascul 3/4" și Quick-Click mascul
Presiune maximă apă	6 bari
Debit maxim	25 L/min
Programare	Până la 4 udări pe zi, 7 zile
Durată udare	1 minut până la 3 ore
Număr zone	1 zonă
Protecție împotriva intemperiilor	IP54
Material carcasă	ABS rezistent la UV
Dimensiuni	12 x 7 x 7 cm
Greutate	250 g (fără baterii)
Întreținere	Curățați filtrul regulat; nu utilizați solvenți
Siguranță	Funcție oprire manuală; antigel automat
Garanție	2 ani

Întrebări frecvente - R7060 WOOX

Cum se instalează programatorul R7060 ?

Fixați programatorul pe un robinet exterior folosind racordul femelă 3/4" cu inel O. Asigurați-vă că inelul este bine așezat pentru a evita scurgerile. Înșurubați apoi furtunul de udare pe ieșirea mascul sau Quick-Click.

Ce tip de baterii se folosesc ?

Folosiți două baterii alcaline AA 1,5V. Nu amestecați baterii noi cu cele uzate. Înlocuiți-le în fiecare sezon sau în caz de afișaj slab.

Cum se programează orele de udare ?

Apăsați butonul PROGRAM pentru a accesa setările. Utilizați săgețile pentru a seta ora de începere, durata (1 minut până la 3 ore) și zilele săptămânii. Confirmați cu OK.

Ce fac dacă programatorul nu se aprinde ?

Verificați dacă bateriile sunt introduse corect (respectați polaritatea). Dacă ecranul rămâne gol, înlocuiți bateriile. Dacă problema persistă, contactați serviciul clienți.

Cum se curăță filtrul ?

Deșurubați capacul filtrului situat la intrarea apei. Scoateți filtrul și clătiți-l cu apă curată. Puneți-l la loc și înșurubați ferm. Efectuați această operațiune cel puțin o dată pe lună.

Pot folosi R7060 cu un colector de apă de ploaie ?

Da, cu condiția ca presiunea apei să fie suficientă (minimum 0,5 bari). Dacă presiunea este prea mică, programatorul riscă să nu se deschidă corect.

Ce fac în caz de scurgere la nivelul racordurilor ?

Verificați dacă inelele O sunt în stare bună și bine poziționate. Strângeți racordurile manual fără a forța. Dacă scurgerea persistă, înlocuiți inelele.

Programatorul este rezistent la îngheț ?

Da, dispune de o funcție antigel care închide automat vana în caz de temperatură apropiată de 0°C. Cu toate acestea, este recomandat să îl aduceți înăuntru iarna.

Câte zone poate gestiona ?

Acest model este proiectat pentru o singură zonă de grădină. Pentru mai multe zone, veți avea nevoie de un programator multizonă sau de un dispozitiv suplimentar.

Cum se resetează setările din fabrică ?

Apăsați simultan butoanele PROGRAM și OK timp de 5 secunde. Ecranul va afișa CLR, apoi setările implicite vor fi restaurate. Bateriile trebuie să fie în poziție.

MANUAL DE UTILIZARE R7060 WOOX

W00X

Green industrial water pump device with black fittings and a small pipe fitting (no visible text or symbols)

If necessary, you can change Male Quick-Click connector to 3/4" Male connector

English

English

English

STEP2.

Illustration of hands assembling or adjusting a mechanical component (no text or symbols visible)

STEP3.

Technical line drawing of a mechanical device with internal components, enclosed in a circular frame (no text or symbols)

English

STEP4.

Illustration of hands assembling or adjusting a mechanical component, no text or symbols present

English

STEP1.

Illustration of a hand holding a mechanical component with an arrow indicating direction (no text or symbols present)

STEP2.

Illustration of hands assembling or adjusting a mechanical component, enclosed in a circular frame (no text or symbols)

STEP3.

Technical line drawing of a mechanical device with internal components, enclosed in a circular frame (no text or symbols)

STEP4.

Illustration of hands assembling a cylindrical object with a cap, enclosed in a circular frame (no text or symbols)

STEP1.

Illustration of a hand holding a mechanical component with an arrow indicating direction (no text or symbols present)

STEP2.

Illustration of hands assembling or adjusting a mechanical component, enclosed in a circular frame (no text or symbols)

STEP3.

Technical line drawing of a mechanical device with internal components, enclosed in a circular frame (no text or symbols)

STEP4.

Illustration of hands assembling a cylindrical object with a cap, enclosed in a circular frame (no text or symbols)

STEP1.

Illustration of a hand holding a mechanical component with an arrow indicating direction (no text or symbols present)

STEP2.

Illustration of hands assembling or adjusting a mechanical component (no text or symbols visible)

STEP3.

Technical line drawing of a mechanical device with internal components, enclosed in a circular frame (no text or symbols)

STEP4.

Illustration of hands assembling a cylindrical object with a cap, enclosed in a circular frame (no text or symbols)

STEP1.

Illustration of a hand holding a mechanical component with an arrow indicating direction (no text or symbols present)

STEP2.

Illustration of hands assembling or adjusting a mechanical component, enclosed in a circular frame (no text or symbols)

STEP3.

Technical line drawing of a mechanical device with internal components, enclosed in a circular frame (no text or symbols)

STEP4.

Illustration of hands assembling a cylindrical object with a cap, enclosed in a circular frame (no text or symbols)

STEP1.

Illustration of a hand holding a mechanical component with an arrow indicating direction (no text or symbols present)

STEP2.

Illustration of hands assembling or adjusting a mechanical component, enclosed in a circular frame (no text or symbols)

STEP3.

Technical line drawing of a mechanical device with internal components, enclosed in a circular frame (no text or symbols)

STEP4.

Illustration of hands assembling a cylindrical object with a cap, enclosed in a circular frame (no text or symbols)

STEP1.

Illustration of a hand holding a mechanical component with an arrow indicating direction (no text or symbols present)

STEP2.

Illustration of hands assembling or adjusting a mechanical component, enclosed in a circular frame (no text or symbols)

STEP3.

Technical line drawing of a mechanical device with internal components, enclosed in a circular frame (no text or symbols)

STEP4.

Illustration of hands assembling or adjusting a mechanical component, no text or symbols present

STEP1.

Illustration of a hand holding a mechanical component with an arrow indicating direction (no text or symbols present)

STEP2.

Illustration of hands assembling or adjusting a mechanical component, enclosed in a circular frame (no text or symbols)

STEP3.

Technical line drawing of a mechanical device with internal components, enclosed in a circular frame (no text or symbols)

STEP4.

Illustration of hands assembling or adjusting a mechanical component, no text or symbols present

STEP1.

Illustration of a hand holding a mechanical component with an arrow indicating direction (no text or symbols present)

STEP2.

Illustration of hands assembling or adjusting a mechanical component, enclosed in a circular frame (no text or symbols)

STEP3.

Technical line drawing of a mechanical device with internal components, enclosed in a circular frame (no text or symbols)

STEP4.

Illustration of hands assembling a cylindrical object with a cap, enclosed in a circular frame (no text or symbols)

STEP1.

Illustration of a hand holding a mechanical component with an arrow indicating direction (no text or symbols present)

STEP2.

Illustration of hands assembling or adjusting a mechanical component, enclosed in a circular frame (no text or symbols)

STEP3.

Technical line drawing of a mechanical device with internal components, enclosed in a circular frame (no text or symbols)

STEP4.

Illustration of hands assembling a cylindrical object with a cap, enclosed in a circular frame (no text or symbols)

STEP1.

Illustration of a hand holding a mechanical component with an arrow indicating direction (no text or symbols present)

STEP2.

Illustration of hands assembling or adjusting a mechanical component, enclosed in a circular frame (no text or symbols)

STEP3.

Technical line drawing of a mechanical device with internal components, enclosed in a circular frame (no text or symbols)

STEP4.

Illustration of hands assembling a cylindrical object with a cap, enclosed in a circular frame (no text or symbols)

STEP1.

Illustration of a hand holding a mechanical component with an arrow indicating direction (no text or symbols present)

STEP2.

Illustration of hands assembling or adjusting a mechanical component, enclosed in a circular frame (no text or symbols)

STEP3.

Technical line drawing of a mechanical device with internal components, enclosed in a circular frame (no text or symbols)

STEP4.

Illustration of hands assembling a cylindrical object with a cap, enclosed in a circular frame (no text or symbols)

STEP1.

Illustration of a hand holding a mechanical component with an arrow indicating direction (no text or symbols present)

STEP2.

Illustration of hands assembling or adjusting a mechanical component, no text or symbols present

STEP3.

Technical line drawing of a mechanical device with internal components, enclosed in a circular frame (no text or symbols)

STEP4.

Illustration of hands assembling a cylindrical object with a cap, enclosed in a circular frame (no text or symbols)

STEP1.

Illustration of a hand holding a mechanical component with an arrow indicating direction (no text or symbols present)

STEP2.

Illustration of hands assembling or adjusting a mechanical component, enclosed in a circular frame (no text or symbols)

STEP3.

Technical line drawing of a mechanical device with internal components, enclosed in a circular frame (no text or symbols)

STEP4.

Illustration of hands assembling a cylindrical object with a cap, enclosed in a circular frame (no text or symbols)

STEP1.

Illustration of a hand holding a mechanical component with an arrow indicating direction (no text or symbols present)

STEP2.

Illustration of hands assembling or adjusting a mechanical component, enclosed in a circular frame (no text or symbols)

STEP3.

Technical line drawing of a mechanical device with internal components, enclosed in a circular frame (no text or symbols)

STEP4.

Illustration of hands assembling a cylindrical object with a cap, enclosed in a circular frame (no text or symbols)