Question 1

Why can't I sign my documents with the WACOM Signature Set STU430 tablet after connecting it?

Accepted Answer

If your WACOM Signature Set STU430 tablet does not allow you to sign your documents after connection, it is usually due to incomplete installation. Here are the steps to check:

1. Check the physical connection

Make sure the mini-USB connector is properly plugged into the back port of the tablet
Check that the USB cable is connected to an active port on your computer
The stylus holder must be secured to hold the cable in place

Important note: The tablet functions as a standard HID device without a driver, but to use all features (including pressure and customization), you need to install the Wacom drivers.

2. Install the Wacom drivers

This is the most common cause of being unable to sign. Download and install the drivers from www.wacom.com by selecting the STU430 model. Restart your computer after installation.

3. Test the signature

Open a compatible electronic signature software (DocuSign, Adobe Sign, etc.)
Use the provided stylus on the 4.5-inch LCD screen of the tablet
The screen will display your signature in real-time - no battery is needed for the stylus, it is powered by the tablet's electromagnetic field

If the problem persists after these steps, check that your signature software supports the STU430 tablet, or contact Wacom support.

Question 2

How to connect the WACOM DTZ-1200W graphics tablet to a computer?

Accepted Answer

To connect your WACOM DTZ-1200W graphics tablet to a computer, follow these simple steps:

1. Check the supplied hardware

Make sure you have the USB cable provided with your tablet, which is used for the connection between the tablet and the computer.

2. Connect the tablet to the computer

Connect one end of the USB cable to the tablet.
Plug the other end into an available USB port on your computer.

3. Turn on the tablet

If your model has a power button, make sure the tablet is turned on.

4. Install the necessary drivers

For the tablet to function properly, download and install the drivers suitable for your model from the official WACOM website. This ensures recognition and compatibility with your operating system.

5. Check the connection

Open a drawing or graphic software to test if the tablet is recognized and functioning correctly.

By following these steps, your WACOM DTZ-1200W graphics tablet should be properly connected and operational with your computer.

Question 3

How to change or configure the screen on the WACOM Signature Set STU430 graphic tablet?

Accepted Answer

The WACOM Signature Set STU430 graphic tablet features a built-in 4.5-inch LCD screen that displays your signatures while you write. This is not a computer screen to be set up as a primary display, but an input device for digital signatures. Here’s how to optimize its use.

Initial setup and connection
Connect the STU430 tablet to your computer using the provided USB cable. Install the WACOM drivers from www.wacom.com so that the product is properly recognized and works with your electronic signature software. After installation, the LCD screen should automatically turn on when the tablet is plugged in.

Preventing ghost images
When the LCD screen operates continuously for a long time, an electric charge remains in the panel and creates ghost images of previous signatures. To avoid this phenomenon, WACOM recommends using an animated screensaver when the tablet is on but not in use. This keeps the screen active without allowing the image to burn in.

Screen maintenance
To keep your screen in good condition, regularly clean the LCD screen and the stylus to remove dust and dirt that can wear the surface. Use an anti-static or slightly damp cloth to clean the screen. Only apply light pressure and do not wet the surface. Never use detergent, solvent, or alcohol, as they can damage the protective coating of the screen. If temporary stains appear on the screen, leave the display on; the stains should disappear within a few hours.

Actions to avoid
Do not scratch the screen and never place sharp objects on the surface. Avoid dropping the tablet or subjecting it to significant shocks, as this could damage the LCD screen or other components. Do not place heavy objects on the tablet and do not subject the screen to strong pressures. Keep the product in a clean, dry environment at room temperature, away from direct moisture.

Software configuration
The STU430 works with Windows, Mac, and Linux operating systems. The operating system's screen settings do not configure the tablet's display (it is not an external screen). Instead, configure the tablet's integration into the signature software you are using (DocuSign, Adobe Sign, etc.) according to their specific instructions. For driver updates or technical issues, visit www.wacom.com/support.

User manual WACOM Graphic tablet : user manuals and guides in PDF

Models WACOM Graphic tablet most viewed

Other categories WACOM

Recent questions about Graphic tablet WACOM