Nl-707540 - Router Icidu - Free user manual and instructions

Product Type	Wireless Router
Model	Nl-707540
Brand	Icidu
Wireless Standard	IEEE 802.11b/g/n
Frequency Band	2.4 GHz
Maximum Data Rate	300 Mbps
Number of Antennas	2 external fixed antennas
Antenna Gain	3 dBi each
Ports	4 x 10/100 Mbps LAN, 1 x 10/100 Mbps WAN
Power Supply	DC 12V, 1A
Dimensions (W x D x H)	150 x 100 x 30 mm
Weight	200 g
Security	WEP, WPA/WPA2-PSK, WPA2-Enterprise
LED Indicators	Power, WAN, LAN (1-4), WLAN
Operating Temperature	0°C to 40°C
Storage Temperature	-20°C to 60°C
Humidity	10% to 90% non-condensing
Button Types	Reset, WPS
Mounting	Desktop
Power Consumption	6W (max)
Warranty	1 year

Frequently Asked Questions - Nl-707540 Icidu

How do I reset the Icidu Nl-707540 router to factory defaults?

Press and hold the Reset button on the back panel for about 10 seconds using a paperclip until all LEDs blink simultaneously. The router will reboot with factory settings.

What is the default IP address to access the router's admin panel?

By default, the router's IP address is 192.168.1.1. Enter it in your browser's address bar, then use username admin and password admin (both lowercase).

How can I change the Wi-Fi password?

Log into the router's web interface, go to Wireless Settings > Security, and enter a new pre-shared key. Save the settings and reconnect your devices with the new password.

What should I do if I forgot my router's admin password?

Perform a factory reset (see related question) to restore the default credentials. After reset, you can log in with the default username and password.

Is this router compatible with all internet service providers?

The router supports standard PPPoE, Dynamic IP, Static IP, and PPTP connection types. It should work with most ISPs that use an Ethernet or PPPoE connection.

How do I update the firmware on the Nl-707540?

Download the latest firmware from the Icidu support page. Log into the router, go to System Tools > Firmware Upgrade, select the file, and click Upgrade. Do not power off during the process.

Can I use this router as a range extender?

The Nl-707540 does not have a dedicated repeater mode. However, you can configure it as a WDS bridge if your main router supports WDS. Check the manual for WDS setup instructions.

What is the maximum number of devices that can connect?

The router can support up to 32 devices connected simultaneously, but performance may decrease with many active connections due to the 300 Mbps limit.

Why is my internet connection dropping frequently?

Possible causes: wireless interference, outdated firmware, overheating, or ISP issues. Try changing the Wi-Fi channel, updating firmware, or moving the router to a well-ventilated area.

How do I set up parental controls on this router?

Access the router's web interface, go to Access Control > Parental Control. You can block specific websites by URL or keyword and set time restrictions for connected devices.

USER MANUAL Nl-707540 Icidu

COMMUNICATION SUPPORT

GIGABIT ROUTER

WIRELESS 300N

300 MBPS

HANDLEIDING NI-707540

White network router with two black antennas and indicator lights (no visible text or symbols on the device body)

NEDERLANDS

INHOUD VAN DE VERPAKKING 4
TECHNISCHE SPECIFICATIES 4
TOEPASSINGMOGELIJKHEDEN 4
HARDWARE INSTALLATIE 5
ROUTER CONFIGURATIE 6
WPS 11

CE/FCC 12

GARANTIE 15

GIGABIT ROUTER WIRELESS 300N 300 MBPS

A connection through a cable modem requires minimal configuration. When you set up an account with your Cable provider, the Cable provider and your Wireless Router will automatically establish a connection, so you probably do not need to enter anything more.

○ Fixed-IP xDSL

Some xDSL Internet Service Providers may assign a Fixed IP Address for your Wireless Router. If you have been provided with this information, choose this option and enter the assigned IP Address, Submit Mask, Gateway IP Address and DNS IP Address for your Wireless Router.

○ PPPoE xDSL

If you connect to the internet using an xDSL Modem and your ISP has provided you with a Password and a Service Name, then your ISP uses PPPoE to establish a connection. You must choose this option and enter the required information.

○ PPTP xDSL

If you connect to the Internet using an xDSL Modem and your ISP has provided you with a Password, Local IP Address, Remote IP Address and a Connection ID, then your ISP uses PPTP to establish a connection. You must choose this option and enter the required information

○ L2TP xDSL

Layer Two Tunneling Protocol is a common connection method used in xDSL connections.

Telstra Big Pond

If your Internet service is provided by Teistra Big Pond in Australia, you will need to enter your information below. This information is provided by Teistra Big Pond.

Indien je over Dynamic IP beschikt klik je op “Cable Modem” je kommt dan direct in het scherm “Dynamic IP”.

○ Cable Modem

A connection through a cable modem requires minimal configuration. When you set up an account with your Cable provider, the Cable provider and your Wireless Router will automatically establish a connection, so you probably do not need to enter anything more:

O Fixed-IP xDSL

Some xDSL Internet Service Providers may assign a Fixed IP Address for your Wireless Router. If you have been provided with this information, choose this option and enter the assigned IP Address, Submit Mask, Gateway IP Address and DNS IP Address for your Wireless Router.

- PPPoE xDSL

If you connect to the Internet using an xDSL Modem and your ISP has provided you with a Password and a Service Name, then your ISP uses PPPoE to establish a connection. You must choose this option and enter the required information.

○ PPTP xDSL

If you connect to the Internet using an xDSL Modem and your ISP has provided you with a Password, Local IP Address, Remote IP Address and a Connection ID, then your ISP uses PPTP to establish a connection. You must choose this option and enter the required information.

○ L2TP xDSL

Layer Two Tunneling Protocol is a common connection method used in xDSL connections.

○ Telstra Big Pond

If your Internet service is provided by Talstra Big Pond in Australia, you will need to enter your information below. This information is provided by Talstra BigPond.

3. IP Address Info 1

PPPoE

Enter the User Name and Password required by your ISP in the appropriate fields. If your ISP has provided you with a "Service Name" enter it in the Service Name field, otherwise, leave it blank.

Basic Settings

This page allows you to define CSSD, and Channel for the wireless connection. These parameters are used for the wireless stations to connect to the Access Point.

Save settings successfully!

You may press CONTINUE button to continue configuring other settings or press APPLY button to restart the system to make the changes take effect.

CONTINUE

APPLY

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

NATIONAL RESTRICTIONS

This device is intended for home and offi ce use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:

COUNTRY RESTRICTION REASON/REMARK
Bulgaria None General authorization required for outdoor use and public service
France Outdoor use limited to Military Radiolocation use.10 mW e.i.r.p. within the Refarming of the 2.4 GHz band has band 2454-2483.5 MHz been ongoing in recent years to allow current relaxed regulation.Full implementation planned 2012
Italy None If used outside of own premises, general authorization is required
Luxembourg None	General authorization required for network and service supply (not for spectrum)
Norway Implemented	This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-Ålesund
Russian Federation None	Only for indoor applications

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee interference will not occur in a particular installation. If this equipment cause harmful interference to radio or television reception, which determined by turning the equipment off and on, the user is enough to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

FCC RF RADIATION EXPOSURE

STATEMENT:

This device has been tested for compliance with FCC RF Exposure (SAR) limits in the typical laptop computer configuration and this device can be used in desktop or laptop computers. This device cannot be used with handheld PDAs (personal digital assistants). This device and its antenna must not be co-located or operated in conjunction with any other antenna or transmitter. SAR measurements are based on a 5mm spacing from the body and that compliance is achieved at that distance.

GARANTIE

© Copyright 2011 ICIDU