VCT-400 - AV Extender Smart-AVI - Free user manual and instructions

Product Type	VGA/AV Extender (Transmitter and Receiver)
Brand	Smart-AVI
Model	VCT-400
Video Bandwidth	400 MHz
Supported Resolutions	Up to 1900x1200 (UXGA)
Video Signal Format	VGA, XGA, UXGA, RGBH, RGsB, Sun, MAC, SGI
Analog Signal Level	1 V (peak-to-peak)
Video Impedance	75 Ohms
Sync Type	TTL, horizontal 15-130 KHz, vertical 30-120 Hz
Sync Connector	3.5 mm Jack socket
Transmission Medium	CAT5 UTP (EIA 568A) cable
Maximum Transmission Distance	Up to 1000 ft (305 m)
Number of Outputs	4 (via remote receiver units)
Power Supply	5V DC @500 mA, connector 5x2.1 mm DC Jack
Enclosure	Compact metal case
Protection	Built-in lightning, power surge, and transient protection
Ground Loop Immunity	High
Sync Preservation	Yes (Sync Format and Polarity Preservation)
Signal Adjustment	Trimmer pots for Red, Green, Blue (on receiver)
What's in the Box	Transmitter (VCA-TX400), power adapter (PS-5D1A-US), VGA cable (male to female)

Frequently Asked Questions - VCT-400 Smart-AVI

What is the maximum resolution supported by the VCT-400?

The VCT-400 supports resolutions up to 1900x1200 (UXGA).

How far can I extend the video signal?

You can extend the signal up to 1000 feet (305 meters) using standard CAT5 UTP cable.

What type of cable is required?

The VCT-400 requires CAT5 UTP cable wired per EIA 568A standard. RJ45 connectors are used.

How do I adjust the picture quality?

On the receiver unit, use the trimmer pots labeled Green, Blue, and Red. Adjust one at a time, starting with Green, then Blue, then Red to fine-tune the signal.

Can I connect the VCT-400 to a Mac or SUN workstation?

Yes, the VCT-400 is compatible with VGA, XGA, Sun, MAC, and SGI signals.

What is the bandwidth of the VCT-400?

The video bandwidth is 400 MHz.

How many displays can I connect?

You can connect up to 4 displays using four VCT-100-RX receiver units (sold separately).

Does the VCT-400 require an external power supply?

Yes, both the transmitter and receiver require a 5V DC @500 mA power supply (included with the transmitter).

What is included in the box?

The box includes the VCA-TX400 transmitter, a 5V DC 1A power supply (PS-5D1A-US), and a VGA male-to-female cable.

Can I use RS232 and IR simultaneously with the VCT-400?

No, you cannot use RS232 and IR at the same time, nor can you use audio simultaneously. The unit supports only one of these functions at a time.

USER MANUAL VCT-400 Smart-AVI

Technical Specifications

Transmitter and receiver
Video
Bandwidth 400MHz
Analog signal Level 1 volt
Impedance 75 ohms
Connector High density HD15
Format VGA/5VGA/XGA/UXGA/RGBH/RGsB
Sync	TTL horizontal SyncRange: 15 to 130 KHz Vertical Sync Range 30 to 120 Hz
Signal level OdB
Impedance 10K ohms
Connector 3.5mm Jack socket
System Cable
Type Cat5 UTP EIA 568A
Connector RJ45
Power
Requirements 5V DC @500 mA
Connector 5x2.1 DC Jack

Purple rectangular device with black ports and a small black connector (no visible text or symbols)

Close-up of a purple electronic device rear panel with two connected VGA connectors and a small indicator light (no visible text or symbols)

© Copyright 2010 Smart-AVI, All Rights Reserved

Notice

The information contained in this document is subject to change without notice. Smart-AVI makes no warranty of any kind with regard to this material, including but not limited to, implied warranties of merchantability and fitness for any particular purpose.

Smart-AVI will not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance or use of this material.

No part of this document may be photocopied, reproduced or translated into another language with out prior written consent from Smart-AVI.

For the complete manual, visit www.smartavi.com.

Smart-AM

2840 N. Naomi Ave.,

Burbank, California 91504

Phone: [phone]

Facsimile: [phone]

Smart-AM

Smart Audio Video Integration

User Manual

VCT400

Purple electronic device with ports and connectors, no visible text or symbols

Use a single CAT5 to broadcast high resolution UXGA to 4 locations 1000ft away

www.smartavi.com

Introduction

The VCT400 allows transmission of high definition video signals over a standard CAT-5 UTP cable over distances of up to 1000 ft.

Features

■ Uses easy to install, inexpensive CAT5.
■ Output reaches up to 1,000 feet.
■ Resolutions up to 1900x1200.
■ 300 MHz Bandwidth.
■ Sends high-resolution VGA signals from one source to up to 4 devices.
■ Compatible with VGA, XGA, Sun, MAC and SGI signals.
■ Sync Format / Polarity Preservation.
■ High ground loop immunity.
■ Built-in lightning, power surge and transient protection.
■ Designated trimmer in the remote unit to compensate for cable length.
■ Compact Metal Case Enclosure.
■ Remote Units come with Buffered Outputs.
■ External power supply.

graph TD
    A["Computer"] --> B["VCA-TX400 Transmitter"]
    B --> C["Up to 1,000 ft"]
    C --> D["VCT-100-RX Transmitter's"]
    D --> E["Four cars on monitors"]
    E --> F["Top panel with car image"]
    style A fill:#f9f,stroke:#333
    style B fill:#ccf,stroke:#333
    style C fill:#cfc,stroke:#333
    style D fill:#fcc,stroke:#333
    style E fill:#ffc,stroke:#333
    style F fill:#cff,stroke:#333

VCT Transmitter Installation Diagram
VCT Receiver Installation Diagram

What's in the box?

Description Part Number
4 port VCA UXGA	VCA-TX400
5VDC 1A Power Supply PS-5D1A-US
VGA cable Male to Female CC-VGAMM-06
Optional Equipment
VCAT-100-RX Receiver Unit	VCT-100-RX

Connecting The Transmitter

1. Connect the output of the computer video card to the video input of the transmitter using the included male to male video cable.
2. Connect local monitor to the VGA out of the transmitter.
3. In the back of the unit connect the CAT5 cable that will connect to the receiver unit.
4. Connect the power supply.

*NOTE: You can not use RS232 and IR at the same time or Audio.

Connecting The Receiver

1. Connect CAT5 cable (coming from the transmitter) to the back of the receiver.
2. Connect monitors to the VGA out connectors on the front of the receiver.
3. Connect the power supply.

Adjusting and Fine Tuning the Signal

In order to fine tune the signal, adjust the individual dials one at a time starting with GREEN, then BLUE and lastly RED. As you turn the dials you will notice the colors slightly change as you increase or decrease the strength.

Preparing & Connecting System CAT5 Cable Following is the wiring standard for terminating CAT 5 cable using RJ-45 connector:

Pair 1 Pins 1 & 2 Pair 2 Pins 3 & 6 Pair 3 Pins 4 & 5 Pair 4 Pins 7 & 8

Connectors: RJ-45

Capacitance: 14 pf/ft (46.2 pf/m)

Conductor Gauge: 24 AWG

Impedance: 100 +/- 15 ohms 4 - Pair