MX-0808-H2A - Router WyreStorm - Free user manual and instructions

Product Type	8x8 HDMI Matrix Switcher with Audio Breakout
Brand	WyreStorm
Model	MX-0808-H2A
Video Inputs	8x HDMI (19-pin Type A)
Video Outputs	8x HDMI (19-pin Type A)
Audio Outputs	8x 5-pin Phoenix Balanced Analog Audio, 8x Toslink Digital Audio
Max Video Resolution	4K60 4:4:4 8bit, 4K60 4:2:2 10bit HDR
HDMI Specification	HDMI 2.0, HDCP 2.2, EDID, CEC
Audio Formats	2ch PCM, Multichannel LPCM up to DTS:X and Dolby Atmos
Control Interfaces	RS-232 (3-pin), LAN (RJ-45), IR, Front Panel, Web UI
Power Supply	100-240V AC, 50/60Hz
Max Power Consumption	60W
Dimensions (HxWxD)	43.5mm x 440mm x 300mm (1.72in x 17.33in x 11.82in)
Rack Height	1U
Weight	3.58kg (7.88lbs)
Operating Temperature	32°F to 113°F (0°C to 45°C)
Storage Temperature	-4°F to 158°F (-20°C to 70°C)
Regulatory Certifications	CE, FCC, RoHS, RCM, EAC
Warranty	5 years limited
Included Accessories	AC power cord, 8x 5-pin terminal blocks, 1x 3-pin terminal block, IR remote, mounting brackets, quickstart guide

Frequently Asked Questions - MX-0808-H2A WyreStorm

How do I find the IP address of the MX-0808-H2A?

Press and hold the UP and Down buttons on the front panel for 3 seconds. The IP address will be displayed on the front panel LCD. Alternatively, use a network scanner to discover the device.

How do I enable Low Power Mode (Standby)?

Access the Web UI (default password: admin), go to Settings tab under Admin section, and set Low Power Mode to On. The unit can be woken via front panel, IR, RS-232, or IP command.

What HDMI cable length should I use for 4K?

For 4K60 4:2:2 HDR, WyreStorm recommends pre-terminated cables up to 5m (16ft). For HD (1080p), up to 20m (65ft). Always use high-quality certified HDMI cables.

Can I control the matrix via RS-232?

Yes. Connect a 3-pin Phoenix terminal to the RS-232 port. The unit uses DTE pinout (pin 2 is RX). Refer to the API document for command set. Default baud rate is 9600.

How do I break out audio from HDMI?

The MX-0808-H2A provides both analog (5-pin Phoenix) and digital (Toslink) audio outputs per output. Connect the appropriate audio cables to extract audio independently from each video output.

Does this matrix support ARC (Audio Return Channel)?

Yes, ARC is supported. Ensure the TV is ARC-compatible and use appropriate HDMI cable with ARC functionality. No additional wiring is needed.

What is the default password for the Web UI?

The default password is 'admin'. WyreStorm recommends changing it to prevent unauthorized access.

How can I reset the matrix to factory defaults?

The manual does not specify a factory reset procedure. If needed, contact WyreStorm support or refer to the API document for a reset command.

The front panel display shows no video. What should I check?

First, verify the matrix is not in Standby. Check that A/V mute is disabled in the Web UI. Ensure all HDMI cables are securely connected, and source/display devices are powered on and outputting a supported resolution.

Can I use third-party IR remotes?

The matrix uses a specific IR code set. You can change the IR code set via the Web UI to avoid interference. The included IR remote works out of the box; third-party remotes may require learning or programming.

USER MANUAL MX-0808-H2A WyreStorm

WyreStorm recommends reading through this document in its entirety to become familiar with the product's features prior to starting the installation process.

IMPORTANT! Installation Requirements

• Visit the product page to download the latest firmware, document version, additional documentation, and configuration tools.
• Read through the Wiring and Connections section for important wiring guidelines before creating or choosing premade cables.
• While this product supports CEC, WyreStorm cannot guarantee compatibility with all forms of CEC communication.

In the Box

1x MX-0808-H2A-MK2 Matrix
1x AC Power Cord (US/UK/EU/AU)
8x 3.5mm 5-Pin Terminal Block
1x 3.5mm 3-Pin Terminal Block
1x IR Remote (CR2025 Battery not Included)
2x Matrix Mounting Brackets with screws
1x Quickstart Guide (this document)

Basic Wiring Diagram

Wiring and Connections

WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in its entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.

IMPORTANT! Wiring Guidelines

• The use of patch panels, wall plates, cable extenders, kinks in cables, and electrical or environmental interference will have an adverse effect on signal transmission which may limit performance. Steps should be taken to minimize or remove these factors completely during installation for best results.
• WyreStorm recommends using pre-terminated HDMI due to the complexity of these connector types. Using pre-terminated cables will ensure that these connections are accurate and will not interfere with the performance of the product.

HDMI Cable Performance Guide

0m	3m	6m	9m	12m	15m	18m	21m	24m	27m	30m
0ft	10ft	20ft	30ft	39ft	49ft	59ft	69ft	79ft	89ft	98ft

RS-232 Wiring

Most control systems and computers are DTE where pin 2 is RX, this can vary from device to device. Refer to the documentation for the connected device for pin functionally to ensure that the correct connections can be made.

Audio Wiring

This matrix contains audio connections for Digital Audio.

This matrix contains audio connections for Analog Audio.

WyreStorm Connector			3rd Party Device
Pin 1	Left Positive (L+) --->	To ---> Left	Positive (L+)
Pin 2	Left Negative (L-) --->	To ---> Left	Negative (L-)
Pin 3	Ground (G)	---> To --->	Ground (G)
Pin 4	Right Negative (R-)	---> To --->	Right Negative (R-)
Pin 5	Right Positive (R+)	---> To --->	Right Positive (R+)

Setup and Configuration

Accessing the Web UI

This matrix uses an Auto IP method to generate the initial IP address based on the network connections. By default the IP address is set to DHCP and will pull the IP address from a connected DHCP server. Should the network not contain a DHCP server the IP address will be generated based on the units mac address. The above operation will occur unless the IP Address setting in the web UI is set to static.

1. Connect the matrix to the same network as a PC.
2. Using a 3rd party network scanner, scan the network for the IP address of the matrix.
3. Open a web browser and enter the IP Address of the matrix.
4. Enter the password for the matrix. Default Password: admin

IP Address Notes

• The IP address of the unit can be displayed by pressing and holding the UP and Down buttons on the front panel for 3 seconds. The IP address will be displayed on the front panel.
• The installer password and general password are the same by default. WyreStorm recommends changing the password for installer login to avoid any unwanted changes being made to the matrix configuration.

Low Power Mode (Standby)

This matrix contains a Low Power Mode that will place the unit into Standby using less power than normal operating mode. While in this mode the Front Panel display and LEDs will be Off and outputs will be powered down. Once a command is sent via the Front Panel buttons, IR remote/control system, or RS-232/IP control system the unit will wake from Standby and be fully operational. The unit can be placed back into standby via the Web UI or by sending an API command as described in the following sections.

Enabling Low Power Mode via Web UI

1. Access the Web UI. Refer to Accessing the Web UI.
2. Navigate to the Settings tab within the Admin section of the Web UI. Default password is admin.
3. Under Low Power Mode, select On to enable.

Troubleshooting

No or Poor-Quality Audio or Video (snow or noisy image)

• Verify that A/V mute is not enabled. Check Web UI for status on the selected output.
• Verify that the matrix is not in Standby. Refer to Low Power Mode (Standby) for details.
• Verify that power is being supplied to the source and receiving device and they are not in standby mode
• Verify that all HDMI connections are not loose and are functioning properly.
• Verify that the output resolution of the source and display is supported by this matrix and receiver.
• If transmitting 3D or 4K, verify that suitable HDMI cables are being used.

Enabling via RS-232/IP

Refer to the products API document for information on Com port and IP addressing settings.

• To place the unit into Standby send the command STANDBY.
• To remove the unit from Standby send the command WAKE.
• To query the current Standby state send the command GET STANDBY.

No or Intermittent 3rd party Device Control

• Verify that the IR and RS-232 cables are properly terminated following the Wiring and Connections section.
• Change the matrix IR code set in order to avoid interference with other devices. Refer to IR Code Settings.

Troubleshooting Tips:

- WyreStorm recommends using a cable tester or connecting the cable to other devices to verify functionality.

Specifications

Audio and Video
Inputs 8x HDMI In: 19-pin type A
Outputs	8x HDMI Out 19-pin HDMI type A8x 5-pin Phoenix Balanced Analog Audio8x Toslink Digital Audio
Video Encoding Uncompressed 18Gbps
End to End Latency None
Audio Formats 2ch PCM | Multichannel: LPCM and Up to DTS-X and Dolby Atmos
ARC Supported
Video Resolutions (Max)	Video Resolution HDMI
	1920x1080p @60Hz 16bit 7m/23ft
	3840x2160p @60Hz 10bit 4:2:2 HDR10/10+ 5m/16ft
	3840x2160p @60Hz 12bit 4:2:0 Dolby Vision 5m/16ft
	3840x2160p @50Hz 10bit 4:2:2 HLG 5m/16ft
	4096x2160p @60Hz 8bit 4:4:4 5m/16ft
Supported Standards DCI | RGB | HDR10 | HDR10+ | Dolby Vision | HLG | BT.2021
Maximum Pixel Clock 600MHz
Communication and Control
HDMI HDMI 2.0 | HDCP 2.2 | EDID | CEC (display power trigger)
RS-232 1x 3-pin Phoenix for API control
LAN	1x 8-pin RJ-45 for API control
Power
Power Supply	100V - 240V 50/60Hz AC
Max Power Consumption	60W
Environmental
Operating Temperature	32°F ~ 113°F (0°C ~ 45°C) | 10% ~ 90%, non-condensing
Storage Temperature	-4°F to ~ 158°F (-20°C ~ +70°C) | 10% ~ 90%, non-condensing
Maximum BTU 205 BTU/hr
Dimensions and Weight
Rack Units/Wall Box	1U
Height	43.5mm/1.72in
Width	440mm/17.33in
Depth	300mm/11.82in
Weight	3.58kg/7.88lbs
Regulatory
Safety and Emission	CE | FCC | RoHS | RCM | EAC

Note: WyreStorm reserves the right to change product specification, appearance or dimensions of this product at any time without prior notice.

Warranty Information

WyreStorm Technologies LLC warrants that its products to be free from defects in material and workmanship under normal use for a period of five (5) years from the date of purchase. Refer to the Product Warranty page on wyrestorm.com for more details on our limited product warranty.