SC-504 - CD Player SuperSonic - Free user manual and instructions

Product Type	CD Player with Radio, USB, and Aux-in
Brand	SuperSonic
Model	SC-504
Power Source	AC 110/220V ~ 60/50Hz or DC 9V (6 x D batteries)
Power Consumption	15W
Output Power	1.5W x 2
Frequency Response	100Hz - 16KHz
Optical Pick-up	3 beams laser
Radio Bands	AM (530-1600 KHz) and FM (88-108 MHz)
CD Playback Formats	CD, CD-R, CD-RW, MP3
USB Playback	Yes (via USB port)
Aux Input	3.5mm jack
Bass Boost	X-BASS button (On/Off)
Display	LCD
Speakers	2 built-in
Antenna	FM telescopic antenna
Programmable Tracks	Up to 20 (CD) / 99 (MP3)
Random Play	Yes
Repeat Modes	Single, All, Folder (MP3 only)
Intro Scan	Yes (CD only)
Handle	Yes
Safety	Class 1 Laser Product

Frequently Asked Questions - SC-504 SuperSonic

How do I switch between CD, USB, and Radio modes?

Use the FUNCTION switch to select AUX/USB/CD/MP3 or RADIO. For USB, press and hold the PLAY/PAUSE/USB button while in AUX/USB/CD/MP3 mode.

What batteries does the SC-504 require?

It requires 6 x UM-1/D size batteries (not included). Do not mix battery types.

How do I program tracks on the CD player?

Press PROG./P-MODE in stop mode, select tracks using SKIP buttons, then press PROG./P-MODE to store. Up to 20 tracks for CD, 99 for MP3.

Why does the display show 'N0D'?

This means no disc is detected or the disc is inserted upside down. Ensure a disc is placed label-side up and try again.

How do I connect an external audio source?

Set FUNCTION to AUX/USB/CD/MP3, connect a 3.5mm audio cable from the external device to the AUX-IN jack on the unit. The unit will automatically switch to Aux mode.

Can I play MP3 files from a USB stick?

Yes. Insert the USB stick into the USB port, press and hold PLAY/PAUSE/USB to enter USB mode, then play as with CDs. Do not use extension cables.

How do I repeat a single track or all tracks?

During playback, press PROG./P-MODE repeatedly. A flashing means repeat one, steady ☐ means repeat all. For MP3, steady ⏻FOLDER repeats the current folder.

What is the Intro Scan function?

Press PROG./P-MODE until 'INTRO' appears on the display. It plays the first 10 seconds of each track (CD only).

How do I clean the CD player?

Use a soft, dry cloth to clean the exterior. For the lens, use a CD lens cleaner. Do not use solvents or spray cleaners.

How do I reset the unit if it malfunctions?

Disconnect the power source for a few minutes and reconnect. For electrostatic discharge, simply reconnect the power to resume normal operation.

USER MANUAL SC-504 SuperSonic

Line drawing of a portable electronic device with two large circular speakers and a front-mounted control panel (no text or symbols)

IMPORTANT: Please read before using and retain for future reference. FAVOR DE LEER EL MANUAL COMPLETAMENTE ANTES DE OPERAR ESTE PRODUCTO. CONSERVAR EL MANUAL PARA FUTURAS REFERENCIAS.

ENGLSIH

IMPORTANT NOTES

INTRODUCTION

• Thank you for buying this product.
• Please read through these operating instructions, so you will know how to operate your equipment properly. After you finished reading the instructions manual, put it in a safe place for future reference.

CAUTION

Use of controls or adjustment or performance of procedures other than those specified herein may result in hazardous radiation exposure.

DANGER

CLASS 1 LASER PRODUCT LUOKAN 1 LASERLAITE KLASS 1 LASERAPPARAT

This Compact disc player is classified as a Class 1 LASER PRODUCT.

THE CLASS 1 LASER PRODUCT label is located on the rear exterior.

NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications.

- Avoid installing the unit in locations described below:

1. Places exposed to direct sunlight or close to heat radiating appliances such as electric heaters, or other equipments that radiate too much heat.
2. Places subjected to constant vibration.
3. Unventilated or dusty places.

4. Humid or moist places.

5. Operate buttons and switches as instructed in the manual.

6. Before turning on the power for the first time, make sure that the power cord is properly installed and the voltage switch is correctly set.
7. Store your CD or other devices in a cool area to avoid damage from heat.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). DO NOT OPEN THE UNIT ANY SERVICING PLEASE REFER TO QUALIFIED SERVICE PERSONNEL.

WARNING:

• Remove batteries if exhausted or if they will not be used for a long period.
• The incorrect use of batteries can cause electrolyte leakage and will corrode the compartment or cause the batteries to burst. Therefore:
• Do not mix battery types, e.g. alkaline with zinc carbonate.
• When inserting new batteries, replace all batteries at the same time.

LOCATION OF CONTROLS

NAMES OF CONTROLS

1. HANDLE
2. FUNCTION SWITCH
3. AUX JACK
4. VOLUME KNOB
5. X-BASS BUTTON
6. CD COMPARTMENT
7. BAND SELECTOR
8. DIAL SCALE
9. TUNING KNOB
10. CD DOOR OPEN/CLOSE
11. POWER INDICATOR
12. FM STEREO INDICATOR
13. CD SKIP/SEARCH BACKWARD BUTTON

14. CD STOP BUTTON

15. SPEAKERS

16. LCD DISPLAY
17. CD SKIP/SEARCH FORWARD BUTTON
18. CD PLAY/PAUSE/USB BUTTON
19. FOLD-/-10 BUTTON
20. CD PROG./P-MODE BUTTON
21. FOLD+/+10 BUTTON
22. USB PORT
23. FM TELESCOPIC ANTENNA
24. BATTERY DOOR
25. AC SOCKET
26. AC VOLTAGE SELECTOR (OPTIONAL)

POWER SOURCE

This unit is designed to be operated on AC/DC.

AC OPERATION

Plug the smaller end of AC power cord into AC jack on unit and the other bigger end into AC wall outlet. The batteries will be automatically disconnected. For dual voltage version, make sure that the AC voltage selector (located on the bottom of the unit) is switched to your local voltage.(optional)

DC OPERATION

Open the BATTERY COMPARTMENT DOOR. Install 6 pcs UM-1/D size batteries (not included) into compartment. Please follow correct polarities as indicated.

CAUTION

Remove batteries if they are flat or not being used for a long period of time. Batteries contain chemical substances, so they should be disposed of properly.

BASIC FUNCTION

SWITCHING ON THE UNIT

Set the FUNCTION switch to AUX/USB/CD/MP3 or RADIO.

TO ADJUST VOLUME

Rotate the VOLUME CONTROL back and forth to increase and decrease volume.

BASS BOOST SYSTEM

The BASS BOOST BUTTON controls the bass of the unit. Bass sound is the lower frequency ranges of sound. The knob can be pushed to OFF or ON position, When the BASS BOOST is on, the unit boosts (increases) the sound output of the bass frequencies.

USING THE RADIO

TUNING IN RADIO STATIONS

1. Move the FUNCTION switch to RADIO position, the POWER indicator will illuminate.
2. Slide the BAND switch to select the desired wave band: AM/FM ST.
3. Tune to required station by rotating the TUNING KNOB.
4. Rotate the VOLUME CONTROL to comfortable volume level.
5. Extend the TELESCOPIC ANTENNA to its full length if you are listening to FM broadcasting. Gently rock the unit back and forth to get the best reception when you are listening to AM program, or place the unit in an open place.

Note: The FM STEREO indicator will be on if you are receiving FM stereo program.

1. Turn off the radio by switching the FUNCTION switch to "OFF" position

USING THE CD/MP3

Discs for Playback

This system can playback all digital audio CD, MP3 finalized digital audio CD-Recordable (CD-R) discs, finalized digital audio CD-Rewritable (CD-RW) discs and CD-DA format digital audio CD/CD-R/CD-RW discs.

LOADING A DISC

1. Set the FUNCTION switch to AUX/USB/CD/MP3 position.
2. Open the CD door.
3. Place an audio CD into the tray with the label side facing up.
4. Close the CD door.

The total number of tracks will appear on the display after several seconds.

1. To remove the CD, press to open CD compartment lid, grasp the CD by its edges, and carefully take it out.

Note:

• To ensure good system performance; wait until the disc tray completely reads the disc before proceeding.
• If no disc is loaded into the compartment, or the disc is placed upside down, the display will show N0D.

PLAYING A DISC

1. Press the PLAY/PAUSE/USB button to start playback.

The playback starts from track 1, the “▶” indicator is shown on the display.

To interrupt playback, press the PLAY/PAUSE/USB button. The “▶” indicator will flash on the display. To resume playback, press the PLAY/PAUSE/USB button again.

1. To stop playback, press the STOP button, the total number of tracks appears on the display.

SELECTING A DESIRED TRACK/PASSAGE

To select a desired track

• Press the CD SKIP/SEARCH FORWARD/BACKWARD button repeatedly in stop mode or during play until the desired track appears on the display.
• Press the PLAY/PAUSE/USB button to start play.

To search for a particular passage during playback (track scanning at high speed)

Press and hold the CD SKIP/SEARCH FORWARD/BACKWARD button to scan the current playing track at high speed until desired point passage, and then release the button. Playback will start again from this point.

To select a song which track number exceeds 10 (for MP3 disc only)

To select a song/track which number exceeds 10, Press the FOLD+/+10 button each time to skip forward/backward 10 tracks, then press the CD SKIP FORWARD/BACKWARD button to select desired track. For example: to select the 17^th track, press FOLD+/+10 button, and then the CD SKIP FORWARD button six times immediately.

To Select A Desired Folder (for MP3 disc only)

(if the MP3 disc contains more than one folder)

Press and hold the FOLD+/+10 or FOLD-/-10 button more than 1 second to skip next/previous folder. Until the desired folder number appears on the LCD display, then release the button,

PROGRAM TRACKS

Programming tracks of disc are possible when playback is stopped. Up to CD 20 tracks /MP3 99 tracks can be stored in the memory in any order.

1. In stop mode, press the PROG./P-MODE button, the PROGRAM will flash and the P01 indicator will be on.
2. Press the CD SKIP/SEARCH FORWARD button to select the first desired track to be programmed.
3. Press the PROG./P-MODE button to enter. The display changes to show P02.
4. Repeat steps 2 & 3 to store other desired tracks until all tracks are programmed.
5. Press the PLAY/PAUSE/USB button to start playback from the first programmed track.
6. Press the STOP button to stop program playback.

To Erase the Memory (Program)

To clear the program, you have two options:

1. Press the STOP button when the disc is stopped, or
2. Open the CD compartment lid, program will be erased.

REPEAT

To Repeat a Single Track

1. Press the PROG./P-MODE button once in play mode, " 🔍 " will flash on the display. The current track will be played repeatedly until the STOP button is pressed
2. Press the PROG./P-MODE button until the "☐" disappear.

To repeat all the Tracks

1. Press PROG./P-MODE button in play mode till “☐” shows steady on the display, all tracks on the disc will be played repeatedly until the STOP button is pressed.
2. To cancel repeat play, press the PROG./P-MODE button till the "☐" disappear.

To repeat current Directory (for MP3 only)

1. Press PROG./P-MODE button in play mode till “ ⏻ FOLDER ” shows steady on the display, The current directory will be played repeatedly until the STOP button is pressed.
2. Press the PROG./P-MODE button till the “☐ FOLDER” disappear.

RANDOM PLAY

Press the PROG./P-MODE button in play mode till the "RDM" shows steady on the display, the random play will start from next track automatically(or press CD skip forward button), until all tracks are played over and then stop. Press the PROG./P-MODE button once to cancel.

INTROSCAN PLAY (for CD disc only)

Press the PROG./P-MODE button in play mode till the “INTRO” shows steady on the display, the unit will start to play the first 10 seconds of music of each track, until all tracks are played over and then stop. Press the PROG./P-MODE button once to cancel.

LISTENING TO USB

USB PLAYBACK

1. Press and hold the PLAY/PAUSE/USB button to select USB playing mode while the FUNCTION switch on main unit is set to AUX/USB/CD/MP3 position.
2. Connect the USB to the USB INPUT. The CD will display total number of tracks stored inside the USB.
3. Press the PLAY/PAUSE/USB button to start playing. Press the PLAY/PAUSE/USB button once again to temporarily stop. The track number will flash.
4. Press the STOP button to stop playing. The display will show total number of tracks.
5. Proceed repeat play (repeat 1/repeat all/repeat folder)/program play/random play/skip up and down operation as the same described in above "USING THE CD/MP3".

Note: To exit USB operation, press and hold PLAY/PAUSE/USB button to return the CD mode.

CAUTION:

• Do not use any USB extension cable for connecting the USB stick which may cause harmful interference
• In case of malfunction due to electrostatic discharge, just reset the product (reconnect of power source may be required) to resume normal operation.

AUX-IN OPERATION

This unit has provided special AUX-IN jack, through this jack other audio sources can be connected to this unit and be amplified.

1. Set the FUNCTION switch to AUX/USB/CD/MP3 position.
2. Connect the audio cable into the AUX-IN jack and the other end connect to the AUDIO OUT jack of the external audio source. The unit will change to AUX mode automatically.
3. Adjust the volume of the main unit to your desired level.
4. Press PLAY of the external audio source (eg. MP3 player) to start playback.

SPECIFICATIONS CD SECTION

Channels: 2 channels

Optical pick-up: 3 beams laser

Frequency Response: 100Hz - 16KHz

RADIO SECTION

Receiving Band:		AM/FM		ST.
Tuning Range:		AM:	530	-	1600 KHz
		FM ST.:	88	-	108 MHz

GENERAL

Output Power: 1.5W x 2

Aux jack: 3.5mm

Power Source: AC 110/220V \~ 60/50Hz

DC 9V 6 x 1.5V UM-1 / D size

Power Consumption: 15 W

Note: Specifications are subject to change for continuous improvement without prior notice.

SPANISH

NOTAS IMPORTANTES

INTRODUCCION