ESCHI1ACOR - Rollerblades Be Cool - Free user manual and instructions

Type de produit	Electric Scooter (e-Scooter)
Marque	Be Cool
Modèle	ESCHI1ACOR (eSC-Hi1)
Dimensions déplié (L x l x H)	1110 x 530 x 1230 mm
Dimensions plié (L x l x H)	1110 x 530 x 535 mm
Poids net	23 kg
Vitesse maximale	40 km/h
Charge maximale	100 kg
Pente maximale	15°
Autonomie (estimée)	Non spécifiée, batterie 15.6 Ah
Température d'utilisation	-10°C à +40°C
Indice de protection	IP54 (résistant aux éclaboussures)
Type de batterie	Lithium-ion
Capacité de la batterie	15.6 Ah
Tension nominale	36 V
Temps de charge	6 à 9 heures
Type de moteur	Moteur brushless à aimants permanents
Puissance nominale du moteur	500 W
Chargeur	Entrée 100-240V AC, 50-60Hz ; Sortie 42V, 2A
Freins	Frein avant et frein arrière (garde-boue)
Pneumatiques	Pneumatiques, pression recommandée 2.2-2.4 bar
Éclairage	Phare avant, feux arrière, réflecteurs
Indicateurs de direction	Gauche et droite
Affichage	LED : vitesse, niveau de batterie, mode, défauts
Âge minimum recommandé	10 ans (avec permis vélo) ; casque obligatoire jusqu'à 12 ans
Garantie	2 ans pour le scooter, 6 mois pour la batterie (Autriche)

Frequently Asked Questions - ESCHI1ACOR Be Cool

What is the maximum speed of the Be Cool ESCHI1ACOR e-scooter?

The maximum speed is 40 km/h, as specified in the technical data.

How long does it take to fully charge the battery?

Charging time is approximately 6 to 9 hours using the original charger.

What is the maximum weight limit for this e-scooter?

The maximum load capacity is 100 kg (220 lbs). Do not exceed this limit.

Can I ride the e-scooter in the rain?

No, the scooter is NOT waterproof. It is only splash resistant (IP54). Riding in rain or wet conditions can damage the scooter and voids the warranty.

How do I fold the e-scooter for storage?

To fold, lift the folding wrench and open it. Then lower the handlebar stem until it locks. Refer to the folding diagram in the manual.

What type of tires does the scooter have and what pressure is recommended?

The tires are pneumatic (air-filled). Recommended tire pressure is 2.2 to 2.4 bar (220-240 kPa). Check and inflate every 2-3 months.

What are the age requirements for using this e-scooter?

Children under 10 years are not allowed. Ages 10-12 require a bicycle license and adult supervision. Helmets are mandatory for children up to 12 years.

How should I maintain the battery if I don't use the scooter for a long time?

Charge the battery to at least 80% if storing for more than 30 days. Fully charge it every 90 days to prevent deep discharge. Store at 0-40°C.

Is it safe to modify the e-scooter or battery?

No, modifying the scooter or battery is forbidden. It can cause instability, fire, or explosion and voids the warranty.

What is covered under warranty?

The scooter has a 2-year warranty and the battery a 6-month warranty (valid in Austria). The warranty excludes water damage, wear and tear, and improper use.

USER MANUAL ESCHI1ACOR Be Cool

Line drawing of a single electric scooter with wheels and suspension components (no text or symbols)

www.becool.at/downloads

Line drawing of a fully electric scooter with suspension components and wheels (no text or symbols)

3.2 Zubehör

Ladegerät x 1

Inbusschlüssel x 1

Line drawing of a rectangular electronic device with two leads and a terminal outlet (no text or symbols)

Simple line drawing of a bent tool or bracket (no text or symbols)

Line drawing of a scooter with extended boom and wheels, showing a right-hand rule for motion (no text or symbols)

Mechanical assembly diagram showing a clamping mechanism with a downward arrow indicating motion (no text or symbols present)

Mechanical assembly diagram showing a lever mechanism with no visible text or symbols

Line drawing of a fully electric scooter with wheels and side-mounted sensor (no text or symbols)

Diagram of an electric scooter's internal components with an upward arrow indicating motion (no text or symbols)

Pure mechanical assembly diagram showing internal components and directional arrows (no text or symbols)

Line drawing of a scooter with visible wheels and side brackets (no text or symbols)

Diagram of an electric scooter's internal components with a downward arrow indicating motion (no text or symbols)

Cross-sectional diagram of a mechanical assembly with arrows indicating force or movement (no text or symbols)

Technical line drawing of an electric scooter's front suspension system with a curved arrow indicating motion (no text or symbols)

Pure mechanical component diagram without any text, numbers, or symbols

Side-view line drawing of a helmet and arm device (no text or symbols)

Line drawing of a person riding a scooter with a speech bubble containing the power button (no text or symbols on the scooter itself)

Side profile line drawing of a person riding an electric scooter with a helmet and seat (no text or symbols)

Line drawing of a person using a scooter with a hand gesture overlay (no text or symbols)

Hinweis:

Line drawing of a person using a scooter with a hand gesture and magnified inset showing the camera (no text or symbols)

Line drawing of a person riding an electric scooter, viewed from the side (no text or symbols)

Simple geometric diagram showing a circle with intersecting lines and a dashed vertical line, no text or symbols present.

Simple line drawing of a wine bottle and a glass with a diagonal line (no text or symbols)

Line drawing of a person riding a scooter through rain, with no text or symbols present

Simple line drawing of a cloud with raindrops inside, enclosed in a circle and diagonal line (no text or symbols)

Simple line drawing of a human figure inside a circle with a diagonal line crossing through it (no text or symbols)

Line drawing of a person riding a scooter with motion arrows indicating movement (no text or symbols)

Side profile illustration of a person riding a scooter with wind turbine blades (no text or symbols)

Line drawings of two people using a scooter, showing front and side views (no text or symbols)

Illustration of batteries and a battery with a lightning bolt symbol (no text or labels)

Symbolic icon of a hammer crossed with a wrench inside a circle (no text or numbers)

Technical line drawing of a mechanical device with two arms and a central component (no text or symbols)

The exclamation point within the triangle is intended to alert the user to the presence of important instructions or statements regarding the operation and/or maintenance of the appliance. Please read the operating instructions carefully before using the unit.

WARNING:

To reduce the risk of electric shock, do not remove the casing of this unit. There are no parts inside that can be repaired by the user. Therefore, do not attempt to repair or service internal parts yourself.

Leave repairs to qualified service personnel.

KICK-STARTER

Please note that the scooter has a kick-start. This means that you first have to push to get going and only then can you accelerate with the help of the throttle lever.

ATTENTION!

Do not ride in rain or wet conditions - the unit is NOT WATERPROOF!

Do not use e-scooter for jumps or stunts!

Do not use it in slippery conditions!

Do not use under the influence of drugs or alcohol! Avoid paths with obstacles such as branches, rubbish or stones!

Avoid steep inclines!

Do not ride faster than recommended!

Do not load the device more than permitted!

CAUTION!

Persons with visual balance, coordination, reflex, muscle or bone problems MUST NOT use this vehicle!

ATTENTION!

Children under the age of 10 are NOT allowed to us the device. Children from the age of 10 with a bicycle driving licence and children up to the age of 12 accompanied by a supervisor who is at least 16 years old may use the scooter - however, detailed instructions on how to use the scooter in a safe manner must be provided beforehand and the existing dangers must be described. In addition, helmets are compulsory for children up to 12 years of age.

BE COOL

2. GENERAL SAFETY NOTE

- Carefully remove the packaging and make sure that the e-scooter is not damaged.

- Do not use the unit if it has any visible damage.

- We recommend wearing qualified and necessary protective clothing such as helmet, hand and knee protectors, etc. as for comparable sports.

- Before getting on the scooter, make sure that you have positioned the scooter on a level surface and that the scooter is switched on.

- Do not open the scooter, modify the scooter, otherwise the manufacturer's warranty will be void and malfunctions may occur that could result in serious physical injury - even death.

- Only ride the scooter in places where riding the scooter is expressly permitted. Only use the scooter outside public places and in places where you do not pose a danger to yourself others or other people's property.

- Never use the scooter under the influence of alcohol and/or drugs.

- Never use the scooter when you are overtired or unfocused. Always have presence of mind and recognise the dangerous situation at an early stage.

- Avoid sudden changes of direction - especially at high speeds.

• Make sure that the protection of the charging socket is always in place.

- The scooter is subject to protection class IP54 and is therefore only spray water resistant NOT WATERPROOF. Never drive through water or rain as this could damage your scooter. Damage caused by water are excluded from this warranty.

- Do not ride through puddles, mud, sand, stones, gravel, grit or on unsuitable rough terrain. For uneven surfaces, it is recommended to carry the scooter until a suitable road surface is found.

The scooter is not suitable for "OFF-road" use.

- Do not drive in bad weather such as snow, rain, hail, icy roads or extreme heat - DANGER OF FLIPPING!

- Avoid driving near swimming pools or other large accumulations of water.

- Prevent riding over obstacles, bumps higher than 1.5cm - even if you are an experienced scooter rider.

- Do not talk on the phone or text while driving. Drive attentively and be aware and alert of your surroundings: road condition, people, weather, objects, etc.

- Do not drive the scooter in places with many people. Drive the scooter with extrem consideration and pay attention to people and objects in the vicinity.

- Do not ride up and down steep hills ( >12^ ). On gentle hills and terrain with slight bumps, it helps to bend the knees slightly when riding to absorb shocks and vibrations. This helps you keep your balance on slight bumps up to a certain intensity.

- Never attempt to ride with more than one person at a time. The scooter is only suitable for riding with a single person.

- Do not transport any objects while driving.

• People with balance disorders should not ride the scooter.

BE COOL

- Do not ride the scooter during pregnancy.

- Children under the age of 12 and older people may only ride under the supervision of experienced and adult persons and protective clothing.

• Note that the braking distance increases proportionally at higher speeds and bodyweight.

- Never get on or off the scooter with a jump. Do not attempt any stunts or tricks with the scooter.

- Be overcarful while driving in the dark or in poorly lit areas.

- Do not exceed or fall below the stated weight limit of the scooter.

- Avoid driving in dangerous places to avoid fire and explosion accidents caused by e.g.: flammable gases, vapours, liquids, dust, fibres.

- Follow all national and local laws applicable to your region regarding the use of your scooter.

- Drive on sight and always be ready to brake.

• Using a different charger may result in damage to the unit and other potential risks.

- Avoid completely discharging the battery. It is best to charge the battery when there is still some remaining capacity (min. 1 bar on the display). This will prolong the life of the battery.

- Place the battery away from fire or corrosive environment while charging as it is classified as flammable and explosive.

- Do not attempt to open the battery housing. If you notice any damage, contact the Service Centre.

- Do not charge the unit in direct sunlight or in the immediate vicinity of an open fire or flames.

• The scooter must not be used during charging.

Riding the scooter is at your own risk and responsibility.

Not all hazards that could lead to injury or even death can be covered in this manual.

ATTENTION!

Note on deep discharge of the battery

The life and performance of a battery depends on its age, care and how often it has been used.

Compared to other battery models, lithium ion batteries have a very low self-discharge and must be charged periodically.

Even if you do not use your scooter, the battery must be charged for at least 1 hour every 2 months, otherwise it will lose capacity. Regular charging protects the battery from deep discharge.

Please note that a deeply discharged battery is irreparably damaged and must be replaced at the owner's expense. For this reason, the battery should never be completely discharged, even during operation!

BE COOL

RECYCLING

The packaging materials can be recycled. It is therefore recommended to dispose of them in the sorted waste.

DISPOSAL

The symbol "crossed-out garbage can" requires the separate disposal of waste electrical and electronic equipment (WEEE). Electrical and electronic devices can contain dangerous and environmentally hazardous substances. Therefore, do not dispose of it in unsorted residual waste, but at a designated collection point for used electrical and electronic equipment. In this way you contribute to the protection of resources and the environment.

For more information, please contact your dealer or local authorities.

DECLARATION OF CONFIRMITY

We hereby confirm that this article complies with the essential requirements, regulations and guidelines of the EU.

You can view the detailed declaration of conformity at any time under the following link:

www.shx.at/downloads

Subject to errors and technical changes.

www.becool.at

3. PACKAGE CONTENS

3.1 E-Scooter

Technical line drawing of a fully electric scooter with suspension components (no text or symbols)

BE COOL

3.2 Accessories

Charger x

Line drawing of a rectangular device with two leads and a power outlet, connected by coiled cables (no text or symbols)

Hex Wrench x 1

Simple L-shaped metal rod or angle (no text or symbols)

T25

User Manual x 1

If you miss something, please contact the dealer in time!

4. INTRODUCTION OF THE PRODUCT

BE COOL

BE COOL

Control buttons

1. Power button:

Long press the power button to turn the device on and off.

2. Function key:

A: To shift gears: Press the function key once briefly.

Pedestrian mode: The gear indicator "D" is not displayed.

Normal mode: The gear indicator "D" lights up white.

Sport mode: The gear indicator "D" lights up red.

B: Pressing the function key twice briefly: switches the front and rear lights on and off.

When the front lights are on, the rear lights are always on.

3. Throttel button:

Stand on the scooter with one foot and push off with your foot to start moving; press the throttel button to accelerate.

4. Brake:

hold the brake handle to brake. Lightly step on the rear fender to assist braking.

5. Cruise mode:

after turning on the constant speed cruise control function, maintain the current vehicle speed for 6 seconds (vehicle speed ≥ 6km/h). Speed mode is automatically activated and exited by pressing the accelerator control again or holding the brake.

Note: When the brake is active, pressing the throttle to accelerate is not allowed!

5. MONTAGE

5.1 Assemble

Technical line drawing of a mechanical assembly with a curved component and an arrow indicating direction (no text or symbols)

1. Unfold the pole and fasten the folding lock.

Diagram of a mechanical device with hoses and connectors, no visible text or symbols

1. Align the communication line terminals of the instrument and the controller with the notch connection.

Technical line drawing of a mechanical lever assembly with no visible text or symbols

1. Align the T-bar of the scooter then insert it into the pole, use the screw provided with the scooter to install and fix it.

5.2 Disassemble

Technical line drawing of a mechanical assembly with no visible text or symbols

1. Loosen the screws that secure the T-bar of the scooter.

Diagram of a mechanical device with hoses and connectors, showing motion arrows (no text or symbols)

1. Pull out the head of the scooter, unplug the communication.

BE COOL

6. HOW TO FOLD

Line drawing of a scooter with extended boom and wheels, showing a right-hand rule for motion (no text or symbols)

1. Lift the folding wrench.		2. Open the folding wrench.

Mechanical assembly diagram showing a clamping mechanism with a downward arrow indicating motion (no text or symbols present)

Mechanical assembly diagram showing a brake lever and wheel (no text or symbols)

BE COOL

7. BATTERY REMOVAL AND INSTALLATION

Line drawing of a fully electric scooter with visible wheels and side-mounted sensors (no text or symbols)

7.1 Remove the battery

1. Unscrew the pedal cover screw counterclockwise.	2. Lift the pedal cover from the quick release screw on the rear wheel side.

Diagram of an electric scooter with a battery and upward arrow indicating motion (no text or symbols)

Pure mechanical assembly diagram showing a valve or actuator without any text, numbers, or symbols

BE COOL

7.2 Install the battery

Technical line drawing of a scooter's front and rear components (no text or symbols)

Diagram of an electric scooter's internal components with a downward arrow indicating motion (no text or symbols)

1. Put the battery vertically into the scooter.

Pure mechanical assembly diagram showing internal components and directional arrows (no text or symbols)

1. Connect the charging plug and the power plug of the controller to the battery.

Technical line drawing of an electric scooter chassis showing internal components and a curved arrow indicating motion (no text or symbols)

3.Cover the pedal and fasten the silicone edge of the pedal.

Pure diagram of a mechanical component with no text, numbers, or symbols

1. Install the screws and tighten it clockwise.

8. HOW TO RIDE

Side-view line drawing of a helmet and its side view showing head, neck, and jaw components (no text or symbols)

1. Wear helmets and other protective equipment while riding.

BE COOL

Line drawing of a person riding a scooter with a speech bubble containing an 'Power' button (no text or symbols on the scooter itself)

1. Long-Press the power button to turn on scooter, stand on the pedal with one foot, push off with your foot to start moving and press the throttle button to accelerate.

Line drawing of a person riding an electric scooter with a helmet and seat (no text or symbols)

1. When the electric scooter is sliding, put the other foot on the pedal and keep both feet remain stable.

Line drawing of a person using a scooter with a hand gesture overlay (no text or symbols)

1. Continuously press the throttle to speed up. Turn the handle to adjust the direction.

BE COOL

Note:

1. The e-scooter is subject to IP54 protection class - the scooter is spray water resistant, but NOT WATERPROOF. You should not operate the scooter in rain, snow, wet or snowy conditions. Damage caused by water are excluded from this warranty.

If you do ride the scooter: rain or snow will increase braking distance and increase the risk of falling. Be sure to drive slowly.

1. The rear brake can be used for normal driving. The front and rear brakes need to be used together for emergency braking.

Don't use the front brake for emergency braking at high speed. Otherwise, it can cause a rollover.

Line drawing of a person using a scooter with a hand gesture and magnified detail showing the camera (no text or symbols)

1. When the scooter stops or runs at a slow speed, you can get off.

Line drawing of a person riding an electric scooter, no text or symbols present

1. Please don't ride at high speed before you are familiar with the performance of the scooter to avoid accidents.

BE COOL

8.1 Indicator

INDICATOR FUNCTIONS

A – Button for left indicator

Turning on left indicator: push the button once

Turning off left indicator: push the button once more

B – Button for right indicator

Turning on right indicator: push the button once

Turning off right indicator: push the button once more

C - switching sides

Push left indicator-button: left indicator flashes → push right indicator-button: right indicator flashes. Push right indicator-button once more: indicator stops flashing.

9. SAFETY NOTES

Simple geometric diagram showing a circle with intersecting lines and a dashed vertical rectangle inside (no text or symbols)

1. Please abide by traffic laws when using electric scooters. Forbidden to ride it into motor lanes.

BE COOL

1. Don't park e-scooters in the building's lobby, evacuation corridor, or safety exit.

Simple line drawing of a wine bottle and a glass with liquid, no text or symbols present

1. DO NOT ride after drinking or taking medicine.

1. Forbidden to ride with overweight (maximum load: 150kg).

Line drawing of a person riding a scooter through rain, with no text or symbols present

Simple line drawing of a cloud with raindrops inside, enclosed in a circle (no text or symbols)

1. You must not drive during rain. Damage caused by water are excluded from this warranty.

BE COOL

Abstract line drawing of a human figure within a circle, no text or symbols present

1. Pregnant women should not be driving with the e-scooter, due to possible injuries. Children under the age of 10 are NOT allowed to drive with the scooter. Children between the age of 10-12 with a bicycle driving license and supervised by someone who is at least 16 years of age may drive the scooter. In addition, children up to 12 years of age are required to wear a helmet.

Line drawing of a person riding a scooter with motion arrows indicating movement (no text or symbols)

Line drawing of a person riding an electric scooter with a wind turbine blade (no text or symbols)

1. Forbidden to ride electric scooters up and down steps or jumping over obstacles.

1. Forbidden to leave the handlebar with one hand or both hands at the same time while riding.

Line drawing of a person riding a bicycle with no text or symbols

Line drawing of two people riding a scooter, viewed from behind (no text or symbols)

1. Forbidden for multiple people or carrying children to ride an scooter at the same time.

BE COOL

Illustration of batteries and a battery with a lightning bolt symbol (no text or labels)

1. Forbidden to modify the battery of an electric scooter privately. Modification of the battery is dangerous, and improper operation may cause the battery to explode or fire.

Symbol of a hammer and wrench crossed inside a circle, no text or numbers present

1. Forbidden to modify electric scooters privately. Private modification may cause an unstable electronic system and cause danger when riding.

Recommended tire pressure: 2,2 Bar \~ 2,4 Bar

BE COOL

1. Before riding an electric scooter, please carefully check the scooter condition make sure that there are no signs of looseness or damage on any part.

Technical line drawing of a mechanical device with two arms and a central component (no text or symbols)

Power circuit, front and rear brakes

Front light	Rear light	Reflector

10. BATTERY PARAMETERS

Name	Parameter	Name	Parameter	Name	Parameter
Type	Li-ion battery	Battery Capacity	15.6Ah	Rated Voltage	36V
Max Charging Voltage	42V	Max Charging Current	2A	Charging time	6-9h
Store Temperature	0-40°C	Charging Temperature	0-40°C	Store Time (0-40°C)	3 months

10.1 Warns for battery

1. The battery must be charged and used within the temperature range required by the battery specification to make the electric scooter work stably and efficiently.
2. Please make sure you take off the charger when you install the battery to prevent any danger from happening.
3. It is never allowed to dissolve or impale the battery, also make sure NO metal stuff go contact with the battery pin electrode, otherwise it might break the battery.

BE COOL

1. It is forbidden to disassemble or pierce the battery pack casing to avoid short circuit caused by metal objects contacting the battery contacts, otherwise it may cause battery damage or personal injury.

2. It is potentially causing fire or explosion if water entering battery circuit, thus stop using the battery in case this happening and go to the after sale immediately.

3. You are only allowed to charge the battery with the original adaptor packed, otherwise it will be causing any unexpected consequence.

4. If finding the battery broken and smells bad or felt hot, you need to stop using and keep the battery away from other stuffs.

5. It helps prolong the lifespan if storing battery after 100% fully charged

6. It is not allowed to store the battery under 0°C or higher 40°C condition.

7. You have to charge it to at least 80% capacity if battery not used more than 30 days. Better to charge it 100% full every 90 days to protect the battery function.

8. It will help prolong the battery lifespan significantly that you charge well accordingly to the manuals after every driving instead of running it out. At room temperature, the battery can play a higher range and performance. But battery life and performance will degrade if used at temperatures below 0°C. Typically, the range may be half or less than at room temperature at 10°C.

9. Do not charge and park e-scooters in residential buildings. Keep away from combustibles when charging, and the charging time should not be too long.

10. Improper disposal of used batteries may seriously pollute the environment. Please abide by local regulations when disposing of this battery.

11. When the internal temperature of the battery exceeds 50^ C, the battery is in a protected state and cannot be charged.

10.3 Charging steps

BE COOL

Method 1

• Remove the battery (7.1 Remove the battery) to open the silicone charging port, plug the charger DC plug into the battery charging port; plug the power cord into the charger, then connect the other port to the socket (100V-240V; 50/60Hz), and confirm the charger indicator is on normally.
• Only use the original electric scooter charger for charging. Do not use any other models of power chargers to avoid danger caused by voltage mismatch.
  • Install the battery (7.2 Install the battery)

Method 2

• Open the charging port cover, make sure the charging port is clean and dry.
• Connect the charger with the battery and the other end with power(100V-240V;50/60Hz), make sure the charging indicator is on.
• When the indicator light on the charger changes, indicating that the charging process is normal, otherwise check if the line connection is good.
• The indicator turns green when the charger is charging; it indicates that the battery has been fully charged. Please stop charging; long time over charge will affect the battery life.

Tip: When the battery is charged separately, the charging status can be viewed on the charging indicator on the battery. It displays red color when charging and green color after full charging.

11 MAINTENANCE

11.1 Maintenance considerations:

- Make sure the electric scooter charger and charging line are disconnected and ensure that the electric scooter is off.

- Wipe the shell with a soft cloth to clean the electric scooter. Please don't put more lubricating oil on bearing when you do the maintenance for it.

- Please check the brake system and tire are vulnerable parts at least once a month. When the brake performance and tire grip are reduced, please contact the dealer to replace the corresponding parts.

- Please do not replace the accessories which not provided by manufacturer without permission, to avoid the safety hazard caused by the inconsistency for accessories with the scooter.

- It is forbidden to clean electric scooters by using water cannon or soaking in liquid. This will cause permanent damage of the electronic devices in the host.

- In order to protect the user's safety, the user can not take apart the electric scooter, otherwise, the user will give up the maintenance warranty rights of the product automatically.

Tips:

• Please charge your electric scooter before storage, for preventing the battery from discharging too long time. Please ensure charge at least once every three months.
• If the storage environment temperature is lower than 0 °C, please don't charge electric scooter. Please charge the e-scooter in inside environment temperature above \$0@age temperature is -0 °C to 4 °C.
• Please keep the electric scooter in a suitable place indoor, dry and appropriate temperature. You can mask the electric scooter to prevent from the dust.

11.2 Maintenance of tires

The tires of this product are pneumatic. When the tire height sinks 20%-30%, it needs to be inflated. The recommended inflated tire pressure is 220-240 Kpa/2,2-2,4 bar. The tire needs to be inflated at least once in 2-3 months. Regular inspection of the inflation can reduce the puncture situation and extend the life of the tire.

1. TECHNICAL DATA

Product name	eSC-Hi1
Main specification
Unfolding size:	mm*mm*mm	1110*530*1230
Folding size:	mm*mm*mm	1110*530*535
Center distance of front and rear wheels	mm	825
Net Weight	kg	23
Max speed	km/h	40
Max load	kg	100
Max climbing angle	°	15
Operating temperature	°C	-10 - +40
Storage temperature	°C	0 - +40
Waterproof level	/	IPX4
Battery specification
Battery type	/	Li-ion battery
Battery capacity	Ah	15.6
Rated voltage(DC)	V	36
Maximum charging voltage(DC)	V	42
Motor specification
Motor type	/	Permanent magnet brushless
Rated power	W	500
Rated voltage	V	36
Charger specification
Input voltage(AC)	V	100~240(50~60Hz)
Output Power	W	84
Output voltage	V	42
Output current	A	2
Contact addresses for further Information		Schuss Home Electronic GmbHScheringgasse 3A-1140 ViennaTel.: [phone]www.becool.atFB-N0: 236974 t / FB-Court: Wien
Service line		DEC Digital-Electronic-Center Service GmbHKelsenstrasse 2A-1030 ViennaTel.: [phone]E-Mail: [e-mail]

BE COOL

WARRANTY

With this quality product from BE COOL, you have made a decision for innovation, durability and reliability.

For this BE COOL device we grant the following warranty periods:

e-Scooter: 2 years from date of purchase valid in Austria

Battery: 6 months from the date of purchase valid in Austria

If, contrary to expectations, service work on your device is still necessary during this period, we hereby guarantee you a free repair (spare parts and working time) or (at the discretion of the company Schuss Home Electronic GmbH) to replace the product. If neither repair nor exchange are possible for economic reasons, we reserve the right to create a time value credit.

Please contact your specialist dealer or us directly. We would like to point out that repair work that has not been carried out by our authorized workshops in Austria immediately terminates the validity of this warranty.

This warranty does not include:

• Repair or replacement of parts due to usual signs of wear.
• Water damage.
• In the event of improper use, we do not assume any consequential damages.
• Damage due to non-compliance with the operating instructions.
• Devices that are used - even partially – commercially.
• Mechanically damaged devices due to external influence (fall, shock, breakage, improper use etc.) as well as signs of wear and tear of an aesthetic nature.
• Damage due to force majeure, water, lightning or overvoltage.
• Devices for which the type designation and/or serial number on the device has been changed, deleted, made illegible or removed.
• Services outside our authorized workshops, the transport costs to an authorized workshop or to us and back as well as the associated risks.

Compatibility issues with other devices, even if they come from the seller.

We would like to emphasize that within the warranty period in case of operating errors or if no error has been detected, a lump sum of € 40, - (indexed base VPI 2010, June 2015) will be charged.

By providing a warranty (repair or replacement of the device), the absolute warranty period of 2 years from the date of purchase is not extended.

The 2-year warranty is only valid on presentation of the proof of purchase (must contain the name and address of the dealer as well as the complete device name) and the corresponding warranty certificate, on which the device type and the serial number must be noted.

Without presenting the guarantee certificate, only the statutory warranty applies!

We expressly point out that the statutory warranty rights are not affected by this guarantee and continue unabated.

BE COOL

A liability for damages on the part of Schuss Home Electronic GmbH and its vicarious agents exists only in the presence of gross negligence or intent. In any case, liability is excluded for lost profits, expected but not occurred savings, consequential damages and damages from claims of third parties. Damage to or for recorded data is always exempt from the obligation to pay damages.

Congratulations on your election. We wish you a lot of fun with your Be Cool e-scooter!

Address

In the case of warranty, this warranty certificate must be followed together with the device by the dealer from whom you purchased the device!