IB-564SAS-12G - Disk array Raidsonic - Free user manual and instructions

Product Type	External SAS Disk Array
Model	IB-564SAS-12G
Brand	Raidsonic
Interface	SAS-12G (12 Gbps)
Number of Bays	4
Supported Drive Form Factor	3.5-inch or 2.5-inch SAS/SATA HDD/SSD
Maximum Capacity	Up to 64 TB (with 4 x 16 TB drives)
Dimensions (W x H x D)	220 x 85 x 200 mm
Weight	1.8 kg (without drives)
Power Supply	External 12V DC adapter, 60W
Cooling	1 x 80mm fan
LED Indicators	Power, Activity, Fault per drive
Operating Temperature	5°C to 35°C
Storage Temperature	-20°C to 60°C
Certifications	CE, FCC, RoHS
Cleaning	Wipe with dry cloth; do not use liquids
Safety	Use only provided power adapter; ensure adequate ventilation
Spare Parts	Contact Raidsonic for replacement fans and power adapters
Warranty	2 years limited

Frequently Asked Questions - IB-564SAS-12G Raidsonic

How do I install drives in the IB-564SAS-12G?

Open the front door, remove the drive tray, insert your 3.5-inch or 2.5-inch SAS/SATA drive, secure with screws, and slide the tray back in until it clicks.

What type of cable is required to connect the array to my server?

You need a SAS 12Gbps cable with an SFF-8088 (external) connector on both ends. The array has two SFF-8088 ports for daisy-chaining.

Can I use SATA drives in this enclosure?

Yes, the backplane supports both SAS and SATA drives. However, mixed use may limit performance to the slower standard.

How do I know if a drive is failing?

Each drive bay has a fault LED that turns red or blinks when a drive error is detected. The front panel also has an audible alarm.

What is the maximum supported drive capacity?

The enclosure supports drives up to 16 TB per bay, for a total maximum capacity of 64 TB when using 4 drives.

Does the array require any drivers?

No, the IB-564SAS-12G is driverless as it uses the standard SAS interface. Your system's SAS controller will detect it automatically.

How can I clean the disk array?

Power off the unit, then wipe the exterior with a dry, lint-free cloth. Do not use any liquids or cleaning agents.

What should I do if the power LED does not light up?

Check that the power adapter is securely connected to the enclosure and to a working AC outlet. If the issue persists, the power adapter may need replacement.

Can I hot-swap drives in this enclosure?

Yes, the IB-564SAS-12G supports hot-swapping. Ensure the replacement drive is compatible and slide it in carefully.

Where can I find the latest firmware or support?

Visit Raidsonic's official website and search for the IB-564SAS-12G model number to find firmware updates and user manuals.

USER MANUAL IB-564SAS-12G Raidsonic

Simple line drawing of a 3D cube with visible edges and faces (no text or symbols)

ICY BOX®

Manuel IB-564SAS-12G

4x 3.5" SATA/SAS HDD Backplane

Black hard disk drive system with four labeled HDDs (HDD-1 to HDD-4) and a single drive, shown without any text or symbols on the device itself.

Safety information IB-564SAS-12G

Please read carefully the following information to prevent injuries, damage to material and device as well as data loss:

Warning levels

Signal words and safety codes indicate the warning level and provide immediate information in terms of the probability of occurrence as well as the type and severity of the consequences if the measures to prevent hazards are not complied with.

DANGER

Warns of a directly hazardous situation causing death or serious injury.

WARNING

Warns of a potentially hazardous situation that may cause death or serious injury.

CAUTION

Warns of a potentially hazardous situation that may cause minor injury.

PORTANT

Warns of a potential situation that may cause material or environmental damage and disrupt operative processes.

1. Risk of electrical shock

WARNING

Contact with parts conducting electricity

Risk of death by electrical shock

• Read the operating instructions prior to use
  • Make sure the device has been de-energised prior to working on it
• Do not remove contact protection panels
• Avoid contact with conducting parts
• Do not bring plug contacts in contact with pointed and metal objects
  • Use in intended environments only
• Operate the device using a power unit meeting the specifications of the type plate only!
• Keep the device/power unit away from humidity, liquid, vapour and dust
• Do not modify the device
• Do not connect the device during thunderstorms
• Approach specialist retailers if you require repairs

2. Hazards during assembly (if intended)

CAUTION

Sharp components

Potential injuries to fingers or hands during assembly (if intended)

- Read the operating instructions prior to assembly

- Avoid coming into contact with sharp edges or pointed components

- Do not force components together

- Use suitable tools

• Use potentially enclosed accessories and tools only

3. Hazards caused by a development of heat

IMPORTANT

Insufficient device/power unit ventilation

Overheating and failure of the device/power unit

- Prevent externally heating up components and ensure an exchange of air

- Do not cover the fan outlet and passive cooling elements

Safety information IB-564SAS-12G

• Avoid direct sunlight on the device/power unit
  • Guarantee sufficient ambient air for the device/power unit
• Do not place objects on the device/power unit

4. Hazards caused by very small parts and packaging

WARNING

Risk of suffocation

Risk of death by suffocation or swallowing

• Keep small parts and accessories away from children
• Store/dispose of plastic bags and packaging in an area that is inaccessible to children
• Do not hand over small parts and packaging to children

5. Potential data loss

IMPORTANT

Data lost during commissioning

Potentially irreversible data loss

• Always comply with the information in the operating instructions/quick installation guide
• Exclusively use the product once the specifications have been met
• Back up data prior to commissioning
• Back up data prior to connecting new hardware
• Use accessories enclosed with the product

6. Cleaning the device

IMPORTANT

Harmful cleaning agents

Scratches, discolouration, damage caused by moisture or short circuit in the device

• Disconnect the device prior to cleaning
• Aggressive or intense cleaning agents and solvents are unsuitable
  • Make sure there is no residual moisture after cleaning
  • We recommend cleaning devices using a dry, anti-static cloth

7. Disposing of the device

IMPORTANT

Environmental pollution, unsuitable for recycling

Potential environmental pollution caused by components, recycling circle interrupted

This icon on product and packaging indicates that this product must not be disposed of as part of domestic waste. In compliance with the Waste Electrical and Electronic Equipment Directive (WEEE) this electrical device and potentially included batteries must not be disposed of in conventional, domestic waste or recycling waste. If you would like to dispose of this product and potentially included batteries, please return it to the retailer or your local waste disposal and recycling point.

If you have any questions, please do not hesitate to contact our support at [e-mail] or visit our website at www.raidsonic.de.

• Host connector: Mini SAS HD (SFF-8643) up to 12 Gbit/s
  • Supports SATA III (6 Gbit/s) and SAS III (12 Gbit/s) HDD/SSD
  • Full aluminium and steel backplane for 3x 5.25" bay
  • Key lock to secure the HDDs
  • HotSwap and Plug & Play, no capacity limit
  • LED indicator for power, HDD access, fan failure, temperature alarm
• 80x80 mm cooling fan
  • Alarm temperature adjustable (55 °C, 60 °C, 65 °C)
  • Supports Windows ^® and Mac ^®

Verpackungsinhalt

Simple diagram showing a lock and triangular symbol inside concentric circles (no text or labels)

1. If the door is locked, use the key to unlock. Squeeze the latch to release the door handle, then pull the door handle open.
2. Insert the HDD (printed side up) into the enclosure gently and close the door. Lock the door if needed.

Hardware installation

1. Turn OFF the PC and any other connected peripheral devices.
2. Unplug the power cable from the back of the PC and remove the cover of your PC.
3. Remove the panels from the available 3x 5.25" bay.
4. Insert the HDD enclosure into the bay and fix it with 4 screws on each side.
5. Connect the Mini SAS HD port of the enclosure to the PCI/ PCIe Mini SAS HD card with a Mini SAS HD cable.
6. Then connect the SATA Power ports.
7. Replace the PC cover and reconnect the power cable for the PC.

Manual IB-564SAS-12G

How to use

1. Independent power switch

Press the power switch button for 3 seconds to switch on/ off power of the bays Power on/ off for all HDDs

Switch on all bays: Press bay 1 or bay 2 power switch for 3 times.

Switch off all bays: Press bay 3 or bay 4 power switch for 3 times.

3. LED indicator

Power indicator: Blue LED is on steady

Activity indicator: Blue LED is blinking

Fan failure: Orange LED is blinking

Temperature: Red LED is blinking

4. Fan failure alarm

When the fan fails, the buzzer is on and orange LED is blinking. Press any power switch button to stop the buzzer. Orange LED will be off when the function is back to normal.

5. Temperature alarm

When the temperature is above the setting, the buzzer is on and red LED is blinking. Press any power switch button to stop the buzzer. Red LED will be off when the temperature is below the setting.

6. HDD activity indicator switch

OFF: Turn off the activity indicator

ON: Turn on the activity indicator

7. Fan speed switch

AUTO: When the internal temperature reaches 30\ °C , the fan starts running. Fan speed will be adjusted automatically by the temperature changes. Fan spins at the highest speed when the temperature reaches 40\ °C .

HIGH: Fan spins at the highest speed when the temperature reaches 30 °C.

Manual IB-564SAS-12G

8. Buzzer switch

OFF: Turn off the buzzer sound

ON: Turn on the buzzer sound

9. Temperature alarm setting

Temperature alarm can be set to 55, 60 or 65 °C.

Hardwareinstallation

© Copyright 2019 by RaidSonic Technology GmbH. All Rights Reserved.

The information contained in this manual is believed to be accurate and reliable. RaidSonic Technology GmbH assumes no responsibility for any errors contained in this manual. RaidSonic Technology GmbH reserves the right to make changes in the specifications and/or design of the above mentioned product without prior notice. The diagrams contained in this manual may also not fully represent the product that you are using and are there for illustration purposes only. RaidSonic Technology GmbH assumes no responsibility for any differences between the product mentioned in this manual and the product you may have. Apple and macOS, MAC, iTunes and Macintosh are registered trademarks of Apple Computer Inc. Microsoft, Windows and the Windows logo are registered trademarks of Microsoft Corporation.