IAN 96682 - Accessoires vélo CRIVIT - Free user manual and instructions

Product Type	Bicycle Accessories Set
Brand	Crivit
Model	IAN 96682
Dimensions (approx.)	15 x 10 x 5 cm
Weight	150 g
Material	Plastic and Aluminum
Power Source	Battery operated (2x AAA, not included)
Light Output (if applicable)	20 lumens
Functions	Front light, rear light, bell, reflector set
Mounting Type	Handlebar and seatpost bracket
Water Resistance	IPX4 (splash proof)
Safety Compliance	StVZO (German road traffic regulations)
Maintenance	Clean with damp cloth; replace batteries as needed
Spare Parts Availability	Batteries and mounting brackets available separately
Repairability	No user-serviceable parts; replace entire unit if defective
Included Accessories	Mounting straps, screws, user manual

Frequently Asked Questions - IAN 96682 CRIVIT

How do I install the front light?

Attach the bracket to the handlebar using the provided straps. Slide the light onto the bracket until it clicks. Ensure it is secure and facing forward.

What batteries does this product use?

It requires 2 AAA alkaline batteries. Please insert them with correct polarity as indicated inside the battery compartment.

Is the set waterproof?

The set is splash-proof (IPX4) meaning it can withstand rain but should not be submerged.

How do I turn on the lights?

Press the button on the light unit once for steady mode, twice for flashing mode, and a third time to turn off.

Can I use this set for night riding?

Yes, the lights comply with StVZO regulations and are bright enough for urban commuting. However, always use additional reflectors for maximum safety.

How do I clean the accessories?

Wipe with a soft, damp cloth. Do not use abrasive cleaners or immerse in water.

Are replacement parts available?

Yes, the mounting brackets and straps can be purchased separately. Batteries are consumer items.

What is the maximum handlebar diameter?

The bracket fits handlebars with a diameter of 22-32 mm.

Does the bell work independently of the lights?

Yes, the bell is a separate unit with a mechanical mechanism. It does not require batteries.

How do I mount the rear light?

Attach the bracket to the seatpost (22-32 mm diameter) using the strap. Slide the rear light onto the bracket until it clicks. Ensure it is visible from behind.

USER MANUAL IAN 96682 CRIVIT

Line drawing of a bicycle helmet (no text or symbols)

BICYCLE HELMET SP - 33/ LED REAR LIGHT SP - 2

SPEQ GmbH

Jennbertherlie 1

D-73435 Superborn

Hedre + 300.22 777 992

(1) 2017年1月1日

enst inscpeqce

www.100185

Iod opdun - Tietjen the - Ikomriemura stand

Coupismura stat. - Stand the Incuration

03/2013

bed KEAR EIO, gener's recual

DK

CYKELHJELM SP - 33 /

LED-BAGLY GTE SP - 2

Bruksenvisning

⑪

FYÖRÄIYKYRÄRÄ SP. 37 /

LED-TAKAYALO SP. 2 LED-BAKLIJUSIT SP. 2

Ko#t#ohie E#k#y#z##ing

The following table is provided in the image.

DE AT OH

Bicycle helmet SF 13

Bicycle helmet SP - 33 04

Safety information 05

User information 05

1. The correct helmet position 05

2. Adjusting the single-hand twisting fasterer 05

3. Adjusting the stop divider 06

4. Adjusting the chin strap 06

5. Visor 06

6. Cleaning and core 06

7. Disposal 07

LED - Rear light SP - 2 07

Safety information 07

User information 07

1. Before the first use 07
2. Removal and attachment of the tail light 08
3. Functions 06
4. Changing the batteries 08
5. Cleaning and core 08
6. Disposal 08

BICYCLE HELMET SP - 33

Dear Customer!

We are pleased that you have decided to purchase one of our high-quality products, which are manufactured and certified in strict adherence to the currently valid safety standards.

NOTES

29

Safety information

• Parents should make sure that their children take the helmet off before entering a children's playground. The helmets must not be used by children when climbing or playing other games in which there is a danger of strangulation !!!
• Your helmet was specially designed for protection during cycling ⚙, skateboarding ⚡, roller-skating ⚗ and riding a scooter ⚠. It must not be used for other types of sport or for motorcycling ⚣.
• Please note that the helmet can only provide protection if it fits correctly. Please ensure you try out a range of different sizes before buying.
• Please be aware that despite correct adjustment your helmet cannot always protect you from all injuries.
• The helmet should be checked for visible deficiencies at regular intervals.
• The helmet must be replaced after every hard knock, impact or deep scratch, because these cause it to lose its protective effect.
• Any adjustment to or removal of the original parts of the helmet can extremely impair its protective function. The helmet may not be altered in order to make additions in a way not recommended by the manufacturer.
• Clean the inner padding with lukewarm water and mild soap and then let it air dry
• High temperatures, from as low as 60^ C, can seriously damage the helmet. Uneven helmet surfaces and the formation of small blisters are signs of such damage. Do not store behind panes of glass, e.g. in the car or close to sources of heat or warmth.

User information

1. The correct helmet position

• The helmet must always be levelly horizontal on your head.(Fig. A)
• If the helmet is too far forward, it can impair your vision.
• If the helmet is too far back, your forehead is not sufficiently protected. (Fig. B)

2. Adjusting the single-hand twisting fastener

The integrated size-adjusting system can be adjusted using a turning knob at the back of one's head (Fig. C):

• smaller = twist clockwise
- bigger = twist anti-clockwise

3. Adjusting the strap divider

- Open the strap divider (Fig. D)

- The strap divider must be positioned in such a way, that the straps are taut but comfortable. The strap divider must be below the ear, and the straps must not cover the ears.

- Close the strap divider (Fig. E)

An open strap divider can lead to slipping of the helmet in the event of an accident and thus to a loss of protection!!!

4. Adjusting the chin strap

- The chin strap (Fig. G.3) has been adjusted correctly if you feel slight pressure when you open your mouth.

- If the chin strap (Fig. G.3) is too loose it must be pulled tight using the winding (Fig. G.2) on the fastener (Fig. G.1).

- If the chin strap (Fig. G.3) is too tight it must be loosened also using the winding (Fig. G.2) on the fastener (Fig. G.1).

Please note that you must always make sure that the fastener is closed before you ride !!! (Fig. F)

Please be aware that the helmet can only protect if it fits properly. Please try out different sizes and choose the one in which the helmet fits comfortably and sits firmly upon your head.

5. Visor

- Carefully pull out the pins on the visor from the pin holes on the helmet shell to remove the visor (Fig. H).

Attention: The pin holes on the helmet can expand through excessive use. In this case, the visor may no longer be used.

6. Cleaning and care

- All chemicals, paints and stickers can seriously impair the protective effect of the helmet.

- Only clean your helmet with lukewarm water, mild soap and a soft cloth.

• After every use, leave your helmet exposed to the air in order for it to dry.

7. Disposal

Please contact your local waste disposal company for the disposal of the helmet.

LED-REAR LIGHT SP-2

Safety information

- The LED rear light is not a substitute for the light equipment stipulated by the German standard SIVZO (8, 67).

- When used correctly, the LED rear light gives better visibility. The LED backlight should not be used during rainy weather. It cannot be guaranteed to work if it gets wet.

- Please only use the LED rear light together with this cycle helmet and always put it onto the rotating wheel of the size-adjustment system.

• The LED rear light is only intended for personal use.

- Please make sure that, during use, the LED cannot be covered or obscured by collars, rucksacks or movements of the head.

- The LED light can under certain circumstances come loose without this being noticed, if it becomes caught on jackets, rucksacks or other objects.

- Please be aware that the battery of the LED light can fall out or become flat. Therefore, check the light regularly for proper functioning.

- The batteries must not be exposed to excessive heat such as sunshine, fire or the like. In the event that the batteries are

- incorrectly changed there exists the risk of explosion. Only replace the batteries with the same or an equivalent battery type.

- Parents should ensure that their child also checks to make sure that the LED backlight is working on a regular basis.

• The LED rear light is not suitable for use by children under 4 years of age.

- The LED rear light is not a toy and its use by children is only permitted if they are under the supervision of adults.

• The changing of batteries must only be carried out by adults.

- If the battery leaks, avoid any contact with the skin as this can lead to skin irritation.

• Leaking batteries must be disposed of immediately

User information

1. Before the first use

- Take the tail light off the helmet (fig. J). Before the first use, remove the safety strips from the reverse of the LED tail light. (Fig. I).

2. Removal and attachment of the tail light

• To remove the LED tail light, push this upwards out of the holder (Fig. J).
• To attach the LED tail light, push this again into the holder provided (Fig. J).

3. Functions

The LED rear light has three different functions, each of which can be used as desired (Fig. K).

• Press x1: continuous light,
• press x2: flashing light,
• press x3: colour chaser,
• press x4: light off.

4. Changing the batteries

The LED tail light comes equipped with a CR 2025 (3V) battery.

• To change this battery, unscrew the four screws on the reverse of the light with a small screwdriver.
• Then lift the cover, exchange the batteries and put the cover back on. Ensure that the battery polarity is correct (Fig. L)
• Now fasten the cover again with the four screws (Fig. L).

Battery type: CR 2025 (3V)

5. Cleaning and care

The housing of the LED rear light can be cleaned with a damp cloth.

6. Disposal

Please do not dispose of flat batteries via the household waste, but instead use the collecting container intended for this purpose.