IAN 273176 - Accessoires vélo CRIVIT - Free user manual and instructions

Product Type	Bicycle Helmet SP-84
Brand	Crivit
Model	IAN 273176
Intended Use	Cycling, skateboarding, roller-skating, scooter riding
Size Adjustment	Single-hand twisting fastener at back of head
Strap Adjustment	Strap divider below ear; chin strap with winding fastener
Fastener Type	Magnetic snap fastener with mechanical lock
Chin Pad	Removable with hook-and-loop fastener
Safety Certification	DIN EN 1078, PSA 89/686/EWG, Notified Body 0197
Service Life	Maximum 3 years from date of manufacture; replace after impact
Cleaning	Lukewarm water and mild soap; air dry
Storage Temperature	Avoid temperatures above 60°C
Disposal	Contact local waste disposal company
Warranty	3 years

Frequently Asked Questions - IAN 273176 CRIVIT

What is the correct position for the helmet on my head?

The helmet must be level on your head, horizontal. If tilted too far forward it impairs vision; if too far back, your forehead is not protected. (See Fig. A & B)

How do I adjust the size of the helmet?

Use the single-hand twisting fastener at the back of your head: turn clockwise to tighten, anti-clockwise to loosen (Fig. C).

Where should the strap divider be positioned?

The strap divider must be below the ear, ensuring the straps are taut but comfortable and do not cover the ears. Always close the divider (Fig. D & E).

How do I adjust the chin strap?

Open your mouth; you should feel slight pressure. If too loose, tighten using the winding (Fig. G.2) near the buckle. If too tight, loosen similarly (Fig. G.1, G.2).

How do I open and close the magnetic fastener?

Push sideways to open. To close, bring the two halves together; they snap due to magnets and lock mechanically. Keep magnets away from sensitive devices (Fig. F).

Can I use this helmet for motorcycling?

No, this helmet is designed for cycling, skateboarding, roller-skating, and scooter riding only. Do not use for motorcycling or other sports.

When should I replace the helmet?

Replace after any hard impact, deep scratch, or if it no longer fits properly. Also replace after 3 years from manufacture date, even if undamaged.

How should I clean the helmet?

Use lukewarm water and mild soap with a soft cloth. Do not use chemicals, paints, or stickers. Let it air dry after each use.

Can I store the helmet in a car?

Avoid high temperatures above 60°C, which can damage the helmet. Do not store behind glass or near heat sources, as blisters or uneven surfaces indicate damage.

How do I dispose of the old helmet?

Contact your local waste disposal company for proper disposal; follow local regulations.

USER MANUAL IAN 273176 CRIVIT

BICYCLE HELMET SP-84

GB IE

BICYCLE HELMET SP-84

owner's manual

NL

FIETSHELM SP-84

Gebruiksaanwijzing

IAN 273176

GB / IE Owner's Manual 04 - 06

Bicycle helmet SP-84 04

Safety information 04
User information 05
1. The correct helmet position 05
2. Adjusting the single-hand twisting fastener 05
3. Adjusting the strap divider 05
4. Adjusting the chin strap 06
5. Opening and closing the magnetic fastener 06
6. Chin pad 06
7. Cleaning and care 06
8. Disposal	06

BICYCLE HELMET SP-84

Dear Customer!

We are pleased that you have decided to purchase one of our high-quality products, which are manufactured and certified in strict adherence to the currently valid safety standards.

Familiarize yourself with this product before first use. Carefully read the operating instructions and the safety information. Use the product only as described and for the indicated purposes. Keep these instructions. If you give the product to a third party, be sure to include all the documents with it.

Safety information

• Warning! This helmet should not be used by children while climbing or doing other activities when there is a risk of strangulation/hanging if the child get strapped with the helmet.

• Your helmet was specially designed for protection during cycling ⏻, skateboarding ⏻, roller-skating ⏻ and riding a scooter ⏻. It must not be used for other types of sport or for motorcycling ⏻.

• Please note that the helmet can only provide protection if it fits correctly. Pleas ensure you try out a range of different sizes before buying.

• Please be aware that despite correct adjustment your helmet cannot always protect you from all injuries.
• The helmet should be checked for visible deficiencies at regular intervals.
• The helmet must be replaced after every hard knock, impact or deep scratch, because these cause it to lose its protective effect. When the helmet no longer fits properly, it must be replaced.
• The helmet must also be replaced when it no longer fits properly or no later than 3 years after the date of manufacture, even if no damage can be detected.
• Any adjustment to or removal of the original parts of the helmet can extremely impair its protective function. The helmet may not be altered in order to make additions in a way not recommended by the manufacturer.
• Clean the inner padding with lukewarm water and mild soap and then let it air dry.
• High temperatures, from as low as 60^ C, can seriously damage the helmet. Uneven helmet surfaces and the formation of small blisters are signs of such damage. Do not store behind panes of glass, e.g. in the car or close to sources of heat or warmth.

User information

1. The correct helmet position

• The helmet must always be levelly horizontal on your head (Fig. A).
• If the helmet is too far forward, it can impair your vision.
• If the helmet is too far back, your forehead is not sufficiently protected (Fig. B).

2. Adjusting the single-hand twisting fastener

The integrated size-adjusting system can be adjusted using a turning knob at the back of one's head (Fig. C):

• smaller = twist clockwise
• bigger = twist anti-clockwise

3. Adjusting the strap divider

• Open the strap divider (Fig. D).
• The strap divider must be positioned in such a way, that the straps are taut but comfortable. The strap divider must be below the ear, and the straps must not cover the ears.

- Close the strap divider (Fig. E).

An open strap divider can lead to slipping of the helmet in the event of an accident and thus to a loss of protection!!!

4. Adjusting the chin strap

• The chin strap (Fig. G.3) has been adjusted correctly if you feel slight pressure when you open your mouth.
• If the chin strap (Fig. G.3) is too loose it must be pulled tight using the winding (Fig. G.2) on the fastener (Fig. G.1).
• If the chin strap (Fig. G.3) is too tight it must be loosened also using the winding (Fig. G.2) on the fastener (Fig. G.1).

Please note that you must always make sure that the fastener is closed before you ride !!! (Fig. F)

Please be aware that the helmet can only protect if it fits properly. Please try out different sizes and choose the one in which the helmet fits comfortably and sits firmly upon your head.

5. Opening and closing the magnetic fastener

- The snap fastener is opened by pushing sideways. To close it, simply fit the two fastener halves into one another. They automatically snap together because of the internal magnets and are held firmly together by a mechanical closure that locks in place (Fig. F).

Attention: Keep magnets away from all devices and objects that can be damaged by magnetic fields.

6. Chin pad

- Place the chin pad on chinstrap and secure it with the hook-and-loop fastener (Fig. H).

7. Cleaning and care

• All chemicals, paints and stickers can seriously impair the protective effect of the helmet.
• Only clean your helmet with lukewarm water, mild soap and a soft cloth.
  • After every use, leave your helmet exposed to the air in order for it to dry.

8. Disposal

Please contact your local waste disposal company for the disposal of the helmet.

Fietshelm SP-84 07

notified body no. 0197

PSA 89/686/EWG

DIN EN 1078