IAN 282725 - Accessoires vélo CRIVIT - Free user manual and instructions

Product type	Bicycle helmet
Brand	Crivit
Model	SP-84 (IAN 282725)
Category	Bicycle accessories
Recommended uses	Bicycle, skateboard, roller skates, scooter
Size adjustment system	Continuous adjustment rotary dial (occipital)
Closure	Magnetic lock with mechanical snap
Chin strap	Adjustable with buckle and loop
Chin guard	Removable, velcro strap attachment
Materials	Hard outer shell, inner padding
Approximate weight	250 g
Care	Clean with lukewarm water and mild soap, air dry
Maximum lifespan	5 years after manufacture, or after any severe impact
Storage temperature	Avoid above 60 °C
Safety standards	Compliant with applicable standards
Included accessories	Chin guard
Repairability	Original parts not modifiable; replace if damaged

Frequently Asked Questions - IAN 282725 CRIVIT

How to properly adjust the helmet on my head?

Place the helmet horizontally on your head. The occipital adjustment system is adjusted using the dial: turn right to tighten, left to loosen. Ensure the helmet does not obstruct your view and does not tilt backward.

How to adjust the straps and chin strap?

Open the strap clip, position it under your ear so that the straps are taut but comfortable. Close the clip. For the chin strap, use the buckle's loop: tighten or loosen until you feel a slight pressure when opening your mouth.

How does the magnetic closure work?

The magnetic closure opens by pushing sideways. To close it, bring the two halves together: the magnets attract and a mechanical snap locks them. Keep the helmet away from devices sensitive to magnetic fields.

What is the proper care for the helmet?

Clean the inner padding with lukewarm water and mild soap. Do not use chemicals, paints, or stickers. Allow to air dry after each use.

When should I replace my helmet?

Replace the helmet after any severe impact, blow, or deep scratch, even if no damage is visible. At most 5 years after its manufacture date, as materials may degrade.

Can I use this helmet for motorcycle or climbing?

No, this helmet is designed only for bicycle, skateboard, roller skates, and scooter. It does not protect against strangulation risks or high-speed impacts.

Is the helmet adjustable for different head sizes?

Yes, thanks to the integrated occipital dial, you can adjust the circumference. Try several sizes in store to choose the one that fits best without being too tight.

What if the buckle or chin strap is too long or too short?

Use the loop on the buckle to adjust the chin strap length. Turn to shorten or lengthen until you get a good fit.

How to install the chin guard?

Place the chin guard over the chin strap and attach it with the velcro strap. Ensure it is properly in place before each use.

Can I paint or stick stickers on the helmet?

No, chemicals, paints, and stickers can damage the protective structure of the helmet. Use only water and mild soap for cleaning.

USER MANUAL IAN 282725 CRIVIT

DE AT CH

FAHRRADHELM SP-84

Gebrauchsanleitung

GB IE

BICYCLE HELMET SP-84

owner's manual

FR BE

CASQUE DE VÉLO SP-84

Mode d'emploi

NL BE

FIETSHELM SP-84

Gebruiksaanwijzing

CZ

CYKLISTICKÁ HELMA SP-84

Navod k použiti

Bicycle helmet SP-84 08

Safety information 08

User information 09

1. The correct helmet position 09

2. Adjusting the single-hand twisting fastener 09

3. Adjusting the strap divider 10

4. Adjusting the chin strap 10

5. Opening and closing the magnetic fastener 10

6. Chin pad 10

7. Cleaning and care 10

8. Disposal 10

BICYCLE HELMET SP-84

Dear Customer!

We are pleased that you have decided to purchase one of our high-quality products, which are manufactured and certified in strict adherence to the currently valid safety standards.

Familiarize yourself with this product before first use. Carefully read the operating instructions and the safety information. Use the product only as described and for the indicated purposes. Keep these instructions. If you give the product to a third party, be sure to include all the documents with it.

Safety information

• Warning! This helmet should not be used by children while climbing or doing other activities when there is a risk of strangulation/hanging if the child gets strapped with the helmet.

• Your helmet was specially designed for protection during cycling ⏻, skateboarding ⏻, roller-skating ⏻ and riding a scooter ⏻. It must not be used for other types of sport or for motorcycling ⏻.

• Please note that the helmet can only provide protection if it fits correctly. Pleas ensure you try out a range of different sizes before buying.

• Please be aware that despite correct adjustment your helmet cannot always protect you from all injuries.
• The helmet should be checked for visible deficiencies at regular intervals.
• The helmet must be replaced after every hard knock, impact or deep scratch, because these cause it to lose its protective effect. When the helmet no longer fits properly, it must be replaced.
• The helmet must also be replaced when it no longer fits properly or no later than 5 years after the date of manufacture, even if no damage can be detected.
• Any adjustment to or removal of the original parts of the helmet can extremely impair its protective function. The helmet may not be altered in order to make additions in a way not recommended by the manufacturer.
• Clean the inner padding with lukewarm water and mild soap and then let it air dry.
• High temperatures, from as low as 60°C, can seriously damage the helmet. Uneven helmet surfaces and the formation of small blisters are signs of such damage. Do not store behind panes of glass, e.g. in the car or close to sources of heat or warmth.

User information

1. The correct helmet position

• The helmet must always be levelly horizontal on your head (Fig. A).
• If the helmet is too far forward, it can impair your vision.
• If the helmet is too far back, your forehead is not sufficiently protected (Fig. B).

2. Adjusting the single-hand twisting fastener

The integrated size-adjusting system can be adjusted using a turning knob at the back of one's head (Fig. C):

• smaller = twist clockwise
• bigger = twist anti-clockwise

3. Adjusting the strap divider

• Open the strap divider (Fig. D).
• The strap divider must be positioned in such a way, that the straps are taut but comfortable. The strap divider must be below the ear, and the straps must not cover the ears.
• Close the strap divider (Fig. E).

An open strap divider can lead to slipping of the helmet in the event of an accident and thus to a loss of protection!!!

4. Adjusting the chin strap

• The chin strap (Fig. G.3) has been adjusted correctly if you feel slight pressure when you open your mouth.
• If the chin strap (Fig. G.3) is too loose it must be pulled tight using the winding (Fig. G.2) on the fastener (Fig. G.1).
• If the chin strap (Fig. G.3) is too tight it must be loosened also using the winding (Fig. G.2) on the fastener (Fig. G.1).

Please note that you must always make sure that the fastener is closed before you ride !!! (Fig. F)

Please be aware that the helmet can only protect if it fits properly. Please try out different sizes and choose the one in which the helmet fits comfortably and sits firmly upon your head.

5. Opening and closing the magnetic fastener

- The snap fastener is opened by pushing sideways. To close it, simply fit the two fastener halves into one another. They automatically snap together because of the internal magnets and are held firmly together by a mechanical closure that locks in place (Fig. F).

Attention: Keep magnets away from all devices and objects that can be damaged by magnetic fields.

6. Chin pad

- Place the chin pad on chinstrap and secure it with the hook-and-loop fastener (Fig. H).

7. Cleaning and care

• All chemicals, paints and stickers can seriously impair the protective effect of the helmet.
• Only clean your helmet with lukewarm water, mild soap and a soft cloth.
  • After every use, leave your helmet exposed to the air in order for it to dry.

8. Disposal

Please contact your local waste disposal company for the disposal of the helmet.

notified body no. 0197

PSA 89/686/EWG

DIN EN 1078