BHB6901X - Range hood BRANDT - Free user manual and instructions

Product Type	Range Hood
Brand	Brandt
Model	BHB6901X
Speeds	3 speeds (low, medium, high) + stop
Lighting	LED, 1 W, average illuminance 48 lux/W
Installation Type	Wall-mounted, external exhaust or recirculation
Maximum Airflow	641.8 m³/h
Minimum Speed Airflow	448.8 m³/h
Maximum Pressure	291 Pa
Annual Energy Consumption (AEC)	88.2 kWh/year
Energy Efficiency Index (EEI)	78.3
Fluid Dynamic Efficiency Index (FDE)	17.7
Lighting Efficiency Index (LE)	48.1
Grease Filtration Efficiency Index (GFE)	84.9
Noise at Maximum Speed	70 dB(LWA)
Noise at Minimum Speed	64 dB(LWA)
Filters	Metal grease filters (cassettes) dishwasher-safe; activated charcoal filter (optional) for recirculation
Grease Filter Maintenance	Clean every 30 hours or at least once a month
Charcoal Filter Replacement	Approximately every year (depending on use)
Power Supply	220-240 V single-phase, 50 Hz, 10 or 16 A
Power Cable	H05 VVF 3G0.75 mm²
Minimum Distance to Cooking Surface	70 cm
After-Sales Service	Customer Service: 09 69 39 25 25 (non-premium rate)

Frequently Asked Questions - BHB6901X BRANDT

How to install the Brandt BHB6901X range hood?

Installation must be carried out by a qualified professional. Attach the wall bracket, connect the exhaust duct (minimum Ø125 mm) and plug it in. Respect a minimum distance of 70 cm above the cooktop.

How to use the hood controls?

Press the buttons: Stop to stop, Low, Medium, High for speeds. The light turns on/off with the dedicated button. An audible signal confirms each press.

When and how to clean the grease filters?

Clean the cassette filters every 30 hours of use or at least once a month. They can be washed in the dishwasher in a vertical position. Use a soft brush and detergent, then dry them before reinstalling.

How to replace the charcoal filter?

For recirculation mode, replace the activated charcoal filter every year. Remove the grease filters, turn the charcoal filter to remove it, then install a new one by reversing the operation.

How to replace the LED lighting?

Before any intervention, cut off the power. Remove the lens, change the LED lamp and replace the lens. Use a lamp of the same type.

What to do if the hood does not work?

First check that there is no power outage and that a speed is selected. If the problem persists, contact after-sales service.

Why is my hood not performing efficiently?

Ensure that the selected speed is suitable for cooking, that the kitchen is well ventilated, and that the charcoal filter is not saturated (in recirculation mode).

What is the safety distance between the hood and the cooktop?

The minimum distance is 70 cm for electric, gas or mixed cookers. Always respect this distance to avoid fire hazard.

Can the hood be used in recirculation mode without a charcoal filter?

No, the activated charcoal filter is essential in recirculation mode to absorb odors. Without it, odors will not be filtered.

Where to find spare parts and after-sales service?

Contact Brandt consumer service at 09 69 39 25 25 (Monday to Saturday) or via www.brandt.com. Use only certified original parts.

USER MANUAL BHB6901X BRANDT

Consejo

4 / MANTENIMIENTO Y LIMPIEZA DEL APARATO

ES

Atención

ES 4 / MANTENIMIENTO Y LIMPIEZA DEL APARATO

• LIMPIEZA DE LA SUPERFICIE EXTERIOR

Atención

You have just acquired a BRANDT hood and we would like to thank you.

We have invested all our dedication and know-how in this appliance so that it would best meet your needs. With innovation and performance, we designed it to be always easy to use.

In the BRANDT product range, you will also find a wide choice of ovens, microwaves, cooking hobs, cookers, dishwashers, washing machines, driers, fridges and freezers, that you can coordinate with your new BRANDT hood.

Visit our website www.brandt.com where you will find all of our products, as well as useful and complementary information.

BRANDT

www.brandt.com

As part of our commitment to constantly improving our products, we reserve the right to make changes to them based on technical advances to their technical and functional features and appearance.

Warning:

Before installing and using your appliance, please carefully read this Guide to Installation and Use, which will allow you to quickly familiarise yourself with its operation.

TABLE OF CONTENTS

EN

1 / NOTICES TO THE USER

• Safety recommendations ____ 27
  • Environmental protection ____ 32
  • Description of your appliance ____ 33

2 / INSTALLING YOUR APPLIANCE

• Using the evacuation mode ____ 34
  • Using the recycling mode ____ 34
  • Electrical connections ____ 35
• Assembling the hood ____ 36
• Assembling the ventilation shaft
  • Outdoor evacuation ____ 37
  • Recycling ____ 38

3 / USING YOUR APPLIANCE

• Description of control panel ____ 39

4 / CARING FOR AND CLEANING YOUR APPLIANCE

• Cleaning the filter cartridges ____ 40
• Changing the carbon filter ____ 40
• Cleaning the outer surfaces 41
• Changing the light bulb ____ 41
• Maintaining your appliance ____ 42

5 / TROUBLESHOOTING ____ 43

6 / AFTER-SALES SERVICE 44

As part of our commitment to constantly improving our products, we reserve the right to make changes to them based on technical advances to their technical and functional features and appearance.

Warning:

Before installing and using your appliance, please carefully read this Guide to Installation and Use, which will allow you to quickly familiarise yourself with its operation.

EN 1 / NOTICES TO THE USER

Attention

Keep this user guide with your appliance. If the appliance is ever sold or transferred to another person, ensure that the new owner receives the user guide. Please become familiar with these recommendations before installing and using your oven. They were written for your safety and the safety of others.

Safety and important precautions

These instructions are also available on the Brandt web site.

Please take heed of this advice when installing and using your appliance. These instructions are intended to protect your safety and the safety of others. Keep this manual with your appliance. If you sell or give the appliance to anyone else, make sure that you also give them this manual.

- In order to constantly improve our products, we reserve the right to to make changes to their technical, functional or aesthetic characteristics in line with technological progress.

- Make a note of the references of your appliance on the "Consumer Service" page so that you can readily find them in future.

Important precautions

- This appliance is designed for use by consumers in the home. Do not use it for commercial or industrial purposes or for any other purpose for which it is not intended.

- Unpack the appliance as soon as you receive it. Check its general appearance. Make a note of any reservations on the delivery slip and keep a copy.

- This appliance can be used by children aged under 8 and by persons with diminished physical, sensory or mental capacities, or persons without any experience or knowledge, provided that they are properly attended to or are given the instructions on how to use the appliance in complete safety and that any potential risks are anticipated. Children must not play with this appliance. The appliance must not be cleaned and maintained by unattended children.

- Caution: The accessible parts of this appliance may become hot when used with cooking equipment.

EN 1 / NOTICES TO THE USER

Electrical risks

- All the power supply circuits must be disconnected before touching the connection terminals. If the power cord is damaged, it must be replaced by the manufacturer, its after-sales service or a similarly qualified person in order to avoid any danger.

- The appliance can be disconnected by using an accessible power outlet or by incorporating a switch in the fixed lines, in accordance with the installation rules.

- Do not change or attempt to change the characteristics of this appliance. Doing so can be dangerous.

- The appliance must only be repaired by an approved specialist.

- Always disconnect the hood before cleaning or maintaining it.

- Never use steam or high-pressure tools to clean your appliance (for the purposes of electrical safety).

- The appliance can be disconnected by using an accessible power outlet or by incorporating a switch in the fixed lines, in accordance with the installation rules.

1 /NOTICES TO THE USER

EN

• Do not change or attempt to change the characteristics of this appliance. Doing so can be dangerous.
• The appliance must only be repaired by an approved specialist.
• Always disconnect the the hood before cleaning or maintaining it.
• Never use steam or high-pressure tools to clean your appliance (for the purposes of electrical safety).

Risk of asphyxiation

- The regulations applying to the evacuation of air must be obeyed. The air must not be sent into a duct used to evacuate fumes from appliances that use gas or other fuels (this does not apply to appliances that only emit air into the room).

- The room must be suitably ventilated when the range hood is used at the same time as appliances that use gas or other fuels (this does not apply to appliances that only emit air into the room).

EN 1 / NOTICES TO THE USER

Risk of fire

- It is forbidden to flambé food or to turn on gas rings that are not covered by a cooking recipient beneath the hood, as the flames may sucked in and damage the appliance.

- Keep a constant eye on fryers used beneath the hood. When heated to very high temperatures, oil and fat can catch fire.

- Clean the appliance and replace the filters at the recommended frequency. Accumulated deposits of grease can cause a fire.

- It is forbidden to use the hood above a fuel fire (wood, coal, etc.).

- If the hood is installed above a gas-fired appliance, leave at least 70 cm between the top of the range and the underside of the hood. If the instructions of the range installed under the hood specify a distance greater than 70 cm, then this distance must be respected.

Warning In the case

In the case of a kitchen heated by a device connected to a chimney (a stove, for example) the "recycling" version of the hood should be installed. Do not use the hood without metal filters.

Suitable ventilation should be provided in the room when the hood is used at the same time as appliances operated by gas or another combustible fuel.

1 / NOTICES TO THE USER

EN

• ENVIRONMENTAL PROTECTION

• This appliance's packaging material is recyclable. Help recycle it and protect the environment by dropping it off in the municipal receptacles provided for this purpose.
• Your appliance also contains a great amount of recyclable material. It is marked with this label to indicate the used appliances that should not be mixed with other waste. This way, the appli

ance recycling organised by your manufacturer will be done under the best possible conditions, in compliance with European Directive 2002/96/EC on Waste Electrical and Electronic Equipment. Contact your town hall or your retailer for the used appliance collection points closest to your home.

- We thank you doing your part to protect the environment.

Warning

Installation should only be performed by installers and qualified technicians.

Warning

Remove the protective film from the cartridge filter before use.

EN 1 / NOTICES TO THE USER

• DESCRIPTION OF YOUR APPLIANCE

2 / INSTALLING YOUR APPLIANCE

EN

• The appliance must be unplugged during installation or when any repairs or maintenance work is being performed.
• Ensure that the network voltage corresponds to the voltage noted on the identification plate located inside the hood.
• If the electrical installation at your residence requires any changes in order to hook up your Appliance, call upon a professional electrician.
• If the hood is being used in evacuation mode, do not connect the appliance to a combustion gas exhaust duct (boiler, chimney, etc.) or to a CMV (controlled mechanical ventilation) system.
• Under no circumstances should the exhaust duct empty into the attic.
• Install the hood at a safe distance of at least 70 cm from an electric, gas or combined cooking hob.

• USING THE EVACUATION MODE

If you possess an outlet to the exterior

(pic. 1)

Your hood can be connected to this outlet using a flue (minimum diameter ∅ mm that is enamelled, in aluminium, flexible or made of inflammable material). If your flue is less than 125 mm in diameter, you must use the recycling mode.

• USING THE RECYCLING MODE

If you do not possess an outlet to the exterior

(pic. 2)

All of our appliances can be used in recycling mode.

In this case, you should add an active carbon filter which will keep in odours.

(See Chapter 4: Changing the carbon filter.)

Advice on how to save energy

To make optimal use of your appliance, keep the length of the duct and the number of bends in the duct to a strict minimum.

EN 2 / INSTALLING YOUR APPLIANCE

• ELECTRICAL CONNECTIONS

During installation and maintenance operations, the appliance must be unplugged from the electrical grid; fuses must be cut off or removed.

The electrical connections are made before the appliance is installed in its housing.

Ensure that:

• the electrical installation has sufficient voltage,
• the electrical wires are in good condition,
• the diameter of the wires complies with the installation requirements.

Warning This app

This appliance is delivered with a H 05 VVF power cord that has three-0.75 mm ² conductors (neutral, phase and ground). It must be connected to the main power supply (which should be a 220-240 V single phase current) via a CEI 60083 standardised socket that should remain accessible after installation, in keeping with installation guidelines.

We cannot be held responsible for any accident resulting from an inexistent, defective or incorrect ground lead. The fuse for your installation must be 10 or 16A. If the power cable is damaged, call the after-sales service department in order to avoid danger.

Warning If the elec

If the electrical installation at your residence requires any changes in order to hook up your appliance, call upon a professional electrician.

Warning If the boo

If the hood displays any malfunctions, unplug the appliance or remove the fuse corresponding to the electrical socket where your appliance is plugged in.

• ASSEMBLING THE HOOD

Warning The hood

The hood must be installed in compliance with all applicable regulations concerning the ventilation of premises. In France these regulations are described in DTU 61.1 from the CSTB. In particular, the evacuated air should never be conveyed to a duct used to evacuate smoke from appliances that use gas or other combustible fuels. Unused ducts may only be used after approval from a competent specialist.

The minimum distance between the cooking surface and the lowest part of the hood must be 70 cm at least. If the instructions for the hob installed under the hood specify a distance of more than 70 cm, this requirement must be respected.

Fixing to the wall :

-Mark a vertical line on the wall centred on the cooktop.

-Mark on the wall the three holes that have to be drilled, using the supplied hood suspension hook and observing the recommended distance (part A Pic 1).

-Drill the three 8 mm diameter holes in a suitable position and insert the plugs.

-Secure the hood's fixing support, ensuring that it is perfectly level (part A Pic. 1).

- Before fixing the hood, mount the non-return valve on the motor outlet

-Fix the extendable evacuation sleeve (not included) to the motor outlet without impeding the movement of the non-return valve (Pic. 3).

-Fit and secure the body of the hood on this support with the screws provided for this purpose (part C Pic. 2).

EN 2 / INSTALLING YOUR APPLIANCE

• ASSEMBLING THE VENTILATION SHAFT

• Outdoor evacuation

- Calculate the final height for fixing the duct support U-bracket (part B Pic 1)

- Mark the two holes accordingly

- Drill 8 mm diameter holes and secure the duct support bracket, ensuring that it is fixed on the same axis as the hood (part B Pic. 1)

- Fix the flat bracket behind the lower duct (part C Pic. 4).

-Fix the two ducts to the hood (Pic. 5)

- Connect the sleeve to the air outlet to the outside.

- Make the electrical connection to the hood using the mains supply cable.

- Lift the upper duct up to the ceiling and fix it to the bracket using the screws.

2 / INSTALLING YOUR APPLIANCE

EN

- Recycling

-Calculate the final height for fixing the duct support U-bracket (part B Pic 1)

-Mark the two holes.

-Drill 8 mm diameter holes and secure the duct support bracket, ensuring that it is fixed in the same axis as the hood (part B Pic 1)

-Fix the flat bracket behind the lower duct (part C Pic. 4).

-Fit the sleeve adapter on the deflector (Pic. 8).

-Connect the extendable sleeve to the deflector.

-Fit the two parts of the duct on to the hood (Pic. 5).

-Fit the deflector (Pic. 8) into the upper duct by the ventilation inlets (Pic. 6).

-Make the electrical connection to the hood using the mains supply cable.

-Lift the upper duct up to the ceiling and fix it to the bracket using the two screws.

Tip

For optimal use of your appliance, we recommend that you connect the hood to a 150 mm-diameter flue (not delivered with the appliance). Minimise the number of angles and bends and the lengths of the flue. In the event that the hood will be operated using outdoor evacuation, you should ensure a sufficient inflow of fresh air to avoid a pressure deficiency in the room.

Warning

Do not use tools to remove the safety film of hood

EN 3 / USING YOUR APPLIANCE

• DESCRIPTION OF CONTROL PANEL

Push button

1. Push stop button, and the motor will stop
2. Push the Low button, the buzzer will buzz once, and the motor runs at low speed
3. Push the Mid button, the buzzer will buzz once, and the motor runs at mid speed
4. Push the High button, the buzzer will buzz once, and the motor runs at high speed.
   5.Push the light button and the two lights will come on. Push it again and the light will turn off.

Stop

Low

Mid

High

Light

Advice on how to save energy

Adjust the speed to the cooking method and the number of pans in use. It is preferable to use the rings at the back of the range.

4 / CARING FOR AND CLEANING YOUR APPLIANCE

EN

Warning

Always unplug the hood before cleaning it or performing other maintenance acts. Regular maintenance of your appliance is a guarantee of proper functioning, good performance and durability.

Warning

Failure to respect the guidelines for cleaning the appliance and filters may cause fires. Please carefully adhere to the maintenance recommendations.

• CLEANING THE FILTER CAR-TRIDGES

They must be cleaned after approximately 30 hours of use or at least once a month. These filters can be cleaned in a vertical position in your dishwasher.

Use a brush, hot water and mild detergent. Rinse and dry them thoroughly before returning them to the hood.

• Dismantling the filter cartridge

– Turn the built-in filter cartridge handle.

- Tilt the filter cartridge downward.

- CHANGING THE CARBON FILTER (optional)

Replace it after approximately 120 hours of use.

- Remove the filter cartridges

- Turn the carbon filter to remove it

- Do the operation in the reverse order to put a new filter back

- Put the filter cartridges back.

EN 4 / CARING FOR AND CLEANING YOUR APPLIANCE

• CLEANING THE OUTER SURFACES

To clean the outside of your hood, use soapy water, but never use abrasive creams, corrosive detergents, scrubbing sponges or brushes. Wipe down with a soft, damp cloth.

• CHANGING THE LIGHT BULB

Warning Before ca

Before carrying out any work, the power supply to the hood must be turned off, either by unplugging it or by using the circuit breaker switch.

Model with LED

- Remove the lighting port

—Change the LED

—Replace the bulb by repeating these steps in reverse order.

Warning

Before carrying out any work, the power supply to the hood must be turned off, either by unplugging it or by using the circuit breaker switch.

• MAINTAINING YOUR APPLIANCE

MAINTENANCE	WHAT TO DO	PRODUCTS/ACCESSORIES TO USE
Top surface and accessories	Never use metal scouring pads, abrasive products or excessively stiff brushes.	To clean the body and the lighting port, you should use only commercial household cleaning products diluted in water and then rinse using clean water, drying with a soft cloth.
Filter cartridge	This filter traps fatty vapours and dust. This component plays an important role in ensuring the effectiveness of your hood. In the event of tough stains, use a non-abrasive cream, then rinse with clean water.	Use a commercial household cleaning product then rinse abundantly and dry. These filters can be cleaned in a vertical position in your dishwasher. (Do not allow them to touch dirty dishes or silverware.)
Activated carbon filter	This filter traps odours and must be changed at least once a year depending on your level of use. You should order these filters from your dealer (quoting the reference shown on the identification plate located inside the hood) and note the date the filter was changed.

To preserve your appliance, we recommend that you use Clearit cleaning products.

Professional expertise

serving individuals

Clearit offers you professional products and solutions designed for the daily care of your household appliances and kitchens.

They are on sale at your regular retailer, along with a complete line of accessories and consumable products.

EN 5 / TROUBLESHOOTING

SYMPTOMS	SOLUTIONS
The hood is not working...	Ensure that:• The power is not cut off.• A speed has been selected.
The hood is not operating effectively...	Ensure that:• The selected motor speed is sufficient for the quantity of smoke and vapours to be cleared.• The kitchen is sufficiently ventilated to allow for fresh air intake.• The carbon filter is not worn (hood operating in recycling mode).
The hood stopped working	Ensure that:• The power is not cut off.• The single-pole cut-off device was not activated.

6 / AFTER-SALES SERVICE EN

Any maintenance on your equipment should be undertaken by :

- either your dealer,

- or another qualified mechanic who is an authorized agent for the brand appliances.

When making an appointment, state the full reference of your equipment (model, type and serial number). This information appears on the manufacturer's nameplate attached to your equipment.

EN 7 / Ecodesign information / Technical product fiche

This device complies with the delegated regulations (EU) 65/2014 and 66/2014 of the European Commission on the eco design requirements and energy labeling of household hoods.

symbol Value Unit

Brand	Brandt
Model number	AD1516X
Annual energy consumption	AEC	88.2	kWh/annum
Energy efficiency index	EEi	78.3	-
Fluid dynamic efficiency index	FDE	17.7	-
Lighting efficiency index	LE	48.1	-
Grease filtering efficiency	GFE	84.9	-
Time increase factor	f	1.4	-
Maximum volumetric airflow of the cooker hood	Qmax	641.8	m3/h
Volumetric airflow at best efficiency point	QBEP	385.8	m3/h
Static pressure at the best efficiency point	PBEP	291	P
Power consumption at the best efficiency point	WBEP	176.0	W
Nominal power consumption of lighting system	WL	1.0	W
Average illumination of the lighting system	Emiddle	48	Lux/W
Power consumption in off mode	Po	0.00	W
Power consumption in standby mode	Ps	--	W
Volumetric airflow at the highest speed setting in normal use	-	621.6	m3/h
Volumetric airflow at the lowest speed setting in normal use	-	448.8	m3/h
Volumetric airflow in intensive or boost mode	-	--	m3/h
Sound power emissions at the highest speed setting in normal use	-	70	dB(LwA)
Sound power emissions at the lowest speed setting in normal use	-	64	dB(LwA)
Sound power emissions in intensive / boost mode	-	--	dB(LwA)

7 / Ecodesign information / Technical product fiche

EN

symbol Value Unit

Brand	Brandt
Model number	AD1519X
Annual energy consumption	AEC	91.1	kWh/annum
Energy efficiency index	EEi	80.5	-
Fluid dynamic efficiency index	FDE	17.5	-
Lighting efficiency index	LE	52.0	-
Grease filtering efficiency	GFE	83.3	-
Time increase factor	f	1.4	-
Maximum volumetric airflow of the cooker hood	Q	647.7	m3/h
Volumetric airflow at best efficiency point	QBEP	384.0	m3/h
Static pressure at the best efficiency point	PBEP	290	P
Power consumption at the best efficiency point	WBEP	176.8	W
Nominal power consumption of lighting system	WL	1.0	W
Average illumination of the lighting system	Emiddle	52	Lux/W
Power consumption in off mode	Po	0.00	W
Power consumption in standby mode	Ps	--	W
Volumetric airflow at the highest speed setting in normal use	-	612.2	m3/h
Volumetric airflow at the lowest speed setting in normal use	-	452.4	m3/h
Volumetric airflow in intensive or boost mode	-	--	m3/h
Sound power emissions at the highest speed setting in normal use	-	71	dB(LwA)
Sound power emissions at the lowest speed setting in normal use	-	66	dB(LwA)
Sound power emissions in intensive / boost mode	-	--	dB(LwA)

Brandt

FR 47

Chère Cliente, Cher Client,

Attention Cet appare

FR 2 / INSTALLATION DE VOTRE APPAREIL

• MONTAGE DE LA CHEMINEE

2 / INSTALLATION DE VOTRE APPAREIL

FR

- Recyclage

fig.13

Conseil

• CHANGEMENT DU FILTRE CHARBON

FR 4 / ENTRETIEN ET NETTOYAGE DE VOTRE APPAREIL

• NETTOYAGE DE LA SURFACE EXTERIEURE

Attention

RELATIONS CONSOMMATEURS

2 / INSTALACE PŘÍSTROJE

2 / INSTALACE PŘÍSTROJE

CZ

CZ 2 / INSTALACE PŘÍSTROJE

• ELEKTRICKÉ ZAPOJENÍ

2 / INSTALACE PŘÍSTROJE

CZ

• MONTÁŽ EXTRAKČNÍHO ZVONU

Pozor

Obr. 1

Obr. 2

Obr. 3

CZ 2 / INSTALACE PŘÍSTROJE

• MONTÁŽ KOMÍNA

• Vypouštění ven

Obr. 3

Obr. 6

Obr. 5

Obr. 4

2 / INSTALACE PŘÍSTROJE

CZ

- Recyklování

Obr. 8

Obr. 4

Obr. 6

Obr. 5

Rada

CZ 4 / ÚDRŽBA A ČIŠTĚNÍ PŘÍSTROJE

• ČIŠTĚNÍ VNĚJŠÍHO POVRCHU

4 / ÚDRŽBA A ČIŠTĚNÍ PŘÍSTROJE

CZ

Pozor

2 / INSTALLATION AF APPARATET

• BRUG MED RECIRKULERINGSVERSIONEN

installationskravene.

Advarsel

Illu. 2

Illu. 3

2 / INSTALLATION AF APPARATET DK

• SAMLING AF VENTILATIONSSKAKTEN

Illu. 3

Illu. 6

Illu. 5

Illu. 4

2 / INSTALLATION AF APPARATET DK

- Recirkulering

Illu. 4

Illu. 8

Illu. 6

Illu. 5

Råd

Gode råd om energibesparelse

4 / PLEJE OG RENG∅RING AF APPARATET DK

Advarsel

4 / PLEJE OG RENG∅RING AF APPARATETDK

- RENG∅RING AF DE YDRE OVERFLADER

4 / PLEJE OG RENG∅RING AF APPARATET DK

Advarsel

الرسم البياني 1

• تركيب الشفاط

خذیر

الرسم البياني 2

• تركيب المدخلة

». التهوية الخارجية

الرسم البياني 4

الرسم البياني 8

الرسم البياني 6

الرسم Bayesian 7

C

الرسم البياني 4

إعادة التدوير