Executive J875 - Wristwatch JAGUAR - Free user manual and instructions

Brand	Jaguar
Model	Executive J875
Product type	Quartz bracelet watch
Origin	Switzerland (Swiss Made)
Case dimensions	Approximately 40 mm diameter
Case thickness	Approximately 10 mm
Weight	Approximately 80 g
Case material	Stainless steel (estimated)
Glass type	Mineral (estimated)
Water resistance	Not specified (splash resistance likely)
Power source	Standard button cell battery (type not specified)
Display	Analog with hands
Main functions	Hours, minutes, seconds, date, chronograph (seconds at center, minutes at 9 o'clock, hours at 6 o'clock)
Chronograph	Start/Stop/Reset, split times, totalizing
Time setting	Crown in position III, seconds stop for precise time setting
Quick date correction	Crown in position II, rotate to desired date
Date/time setting after battery change	6-step procedure (see manual)
Chronograph hand alignment	Zero position adjustable via pushers A and B
Care and cleaning	Avoid water and shocks; clean with a soft, dry cloth
Precautions	Do not operate crown under water; avoid magnetic fields
Spare parts and repairability	Battery replaceable by a watchmaker; original parts available at authorized service center
General information	32-page instruction manual including diagrams and procedures

Frequently Asked Questions - Executive J875 JAGUAR

How to start and stop the chronograph?

Press pusher A to start timing. Press A again to stop. To reset, press pusher B. The chronograph hands (center seconds, minutes, hours) return to zero.

How to measure a split time?

During timing, press pusher B to display the split time. Timing continues in background. Press B again so that the hands catch up to the elapsed time quickly.

How to set the time to the exact second?

Pull the crown to position III when the second hand is at 60. Turn the crown to set the hour and minute hands. Push the crown back to position I exactly at the time signal.

How to quickly correct the date?

Pull the crown to position II (watch continues running). Turn the crown in one direction until the current date appears. Push the crown back to position I. Avoid setting the date between 9 PM and midnight.

What to do if the chronograph hands are not at zero?

Pull the crown to position III. Simultaneously press pushers A and B for 2 seconds to activate correction mode. Use A to adjust the second hand, then press B to move to hour and minute hands. Push crown back to position I to finish.

How to set date and time after a battery change?

Follow procedure: pull crown to position II and set the day before the current date. Then pull to position III, set the correct date, then set the time. Push crown back to position I. Respect the 24-hour cycle.

Is my watch water-resistant?

The manual does not specify water resistance. As a precaution, avoid any contact with water and do not operate crown under water. Consult a watchmaker for a water resistance test.

What type of battery to use and how to replace it?

The watch uses a standard button cell battery (type not specified). Replacement should be done by a professional watchmaker to ensure water resistance and proper functioning.

How to clean my watch?

Use a soft, dry cloth to wipe the case and bracelet. Avoid chemicals and submersion in water. For stubborn dirt, a slightly damp cloth is acceptable, followed by immediate drying.

Where can I find spare parts?

Spare parts (batteries, clasps, crystals) are available from authorized Jaguar watchmakers. Contact customer service to order original parts.

USER MANUAL Executive J875 JAGUAR

Line drawing of a stylized animal head in profile (no text or symbols)

JAGUAR SWISS MADE

USER GUIDE IJM5030D

INDEX

Español > p.01

English > p.13

Français > p.25

Deutsch >p.37

Italiano > p.49

Manual del usuario

• Description of the display and control buttons.... 14
• Chronograph 15
• Setting the time 20
• Setting the date (quick mode) 21
• Setting the date time following a battery change.... 22

By virtue of the regulations pursuant to the handling of waste products deriving from electronic and electrical equipment, end of life cycle watch making products must be selectively collected for processing. You may therefore dispose of your quartz watch making products at any of our retail outlets or any other authorized collection point.

The selective collection, processing, rating and recycling of these products helps contribute to safeguarding the environment and protecting our health.

Description of the display and control buttons

Chronograph: Basic function

START/STOP/RESET

Example:

① Start: Press push-button A.
② Stop: to stop the timing, press push-button A once more and read the three chronograph hand: 1h/20min/10sec
③ Zero positioning:

Press push-button B. (The three chnorograph hands will be reset to their zero positions).

Chronograph: Accumulated timing

Minute counter

Hour counter Hour counter

Example: Example:

① Start: (start timing)
② Stop: (c.g. 15 min 5 sec following ①)
③ Restart: (timing is resumed)
-④ *Stop: (c.g. 13 min 5 sec following ③) = 28 min 10 sec (the accumulated measured time is shown).

⑤ Reset:

The three chronograph hands are returned to their zero positions

Please note:

Following*4, the accumulation of the timing can be continued by pressing push-button A (Restart / Stop, Restart/Stop,...)

Chronograph

Intermediate or interval timing

Minute counter

Push-button A

① Start: (start timing)

Display interval: c.g. 10 minutes, 10 seconds (timing continues in the background).

② Making up the measured time:

(the 3 chronograph hands are quickly advanced to the ongoing measured time).

③ Stop: (Final time is displayed)

④ Reset:

The 3 chronograph hands are returned to their zero position.

Please note:

Following ③, further intervals or intermediates can be displayed by pressing push-button B (display interval/make up measured time,...)

Adjusting the chronograph hands to zero position

Minute counter Center stop-second

Example:

One or several chronograph hand are not in their correct zero positions and have to be adjusted (e.g. following a battery change).

① Pull out the crown to position III (all 3 chronograph hands are in their correct or incorrect zero position).
② Keep push-buttons A and B depressed simultaneously for at least 2 seconds (the centre stop-second rotates by 360^ corrective mode is activated)

Adjusting the centre stop second: Single step √A 1 x short Continuous long
Adjusting the next hand B
Adjusting the hour counter hand (position 6h)
Single step A1 x short Continuous long
Adjusting the next hand B
Adjusting the minute counter hand (position 9h)
Single step 1x short Continuous long
③ Returning the crown to position I Termination of the chronograph hands adjustment (can be carried out at any time)

Setting the time

① Pull out the crown to position III * (the watch stops).
② Turn the crown until you reach the correct time 8:45.
③ Push the crown back into position 1.*

Setting the date (quick mode)

① Pull out the crown to position II (the watch continues to run).
② Turn the crown until the correct date 1 appears.
③ Push the crown back into position 1.

Please note: Please note:

In order to set the time to the exact * second, ① must be pullet out when the second hand is in position "60" (I). Once the hour and minute hands have been set, ③ must be pushed back into position I at the exact second.

During the date changing phase between 9 PM and 12 PM; the date must be set to the date of the following day.

Setting the date/time

Following a battery change

Example:

Date/time on the watch: 17/1:25 AM – Present date/time: 4/8:30 PM –

① Pull out the crown to position II (the watch continues to run).
② Turn the crown until yesterday's date appears 3.

③ Pull out the crown to position * III (the watch stops).
④ Turn the crown until the correct date appears.
⑤* Continue to turn the crown * until the correct time 8:30 PM appears.
⑥ Push the crown back into position 1.

Please note:

To set your watch to the exact * second please refer to the chapter entitled "setting the time".

- Please observe the AM/PM clock * rhythm.

Mode d'emploi

Compteur des heures

Exemple:

Nota: Nota:

Empty white rectangle with black border (no text or symbols)

FESTINA GROUP

Via Layetana, 20

08003 BARCELONA

A COMPANY OF THE FESTINA GROUP