HDM1022 - Drill Ferm - Free user manual and instructions

Brand	Ferm
Model	HDM1022
Product type	Hammer drill with hammer function
Supply voltage	230 V~, 50 Hz
Rated power input	1500 W
No-load speed	350 - 800 rpm
Impact rate	1100 - 2700 impacts/min
Max. drilling diameter (wood)	40 mm
Max. drilling diameter (steel)	13 mm
Max. drilling diameter (concrete)	36 mm
Weight	6 kg
Chuck type	SDS (with locking ring)
Operating modes	Drilling, impact, demolition hammer
Electronic speed control	Yes (knob 1-6)
Auxiliary handle	Yes, adjustable
Depth stop	Yes
Dust collector	Yes (for ceiling drilling)
Sound pressure level	98.5 dB(A) (perforation)
Vibration level (main handle)	19.819 m/s² (perforation)
Double insulation	Yes
Maintenance	Regular lubrication, carbon brush replacement
Warranty	See included terms

Frequently Asked Questions - HDM1022 Ferm

How to change the bit or chisel on the HDM1022 drill?

To attach an accessory, slide the locking ring back, insert the accessory into the SDS chuck, turn it counterclockwise until it clicks, then release the ring. To remove, pull the ring back, remove the accessory, then release.

How to adjust the drilling depth?

Loosen the auxiliary handle, insert the depth stop into the designated hole, adjust it to the desired position, then tighten the handle.

How to use the impact mode?

Turn the drilling selector and the impact selection lever to position 'B' (impact drill). For demolition hammer, use position 'A' with a suitable chisel.

What is the dust collector for?

The dust collector prevents dust from entering the machine when drilling into ceilings. It mounts onto the accessory shaft before insertion into the chuck.

How to lubricate the drill?

Regularly grease the insertion shaft of accessories. Check the internal grease level by removing the cover and cap of the lubrication point (mark 9); add grease if necessary, then close.

When to replace the carbon brushes?

Replace the brushes when they are worn (the machine runs irregularly). Remove the brush holders with a screwdriver, clean or replace both brushes at the same time, then reinstall. After installation, run the machine at no load for 15 minutes.

What are the maximum drilling diameters?

Wood: 40 mm, steel: 13 mm, concrete: 36 mm. Use suitable drills.

How to adjust the rotational speed?

Use the speed presetting knob (1-6). During operation, you can also adjust the speed by turning the knob. Low speed (1-2) is suitable for steel, medium (3-4) for wood, high (5-6) for concrete.

What safety precautions should be taken?

Wear safety glasses and hearing protection. Hold the machine with both hands. Check for electrical wires in walls before drilling. Do not use damaged accessories. Disconnect the plug before any maintenance.

How to recycle the drill at end of life?

Do not dispose of it with household waste. In accordance with the WEEE directive, take it to a collection point for recycling of electrical and electronic equipment.

USER MANUAL HDM1022 Ferm

Fig. D

Fig. E

ROTARY HAMMER

Thank you for buying this Ferm product.

By doing so you now have an excellent product, delivered by one of Europe's leading suppliers. All products delivered to you by Ferm are manufactured according to the highest standards of performance and safety. As part of our philosophy we also provide an excellent customer service, backed by our comprehensive warranty. We hope you will enjoy using this product for many years to come.

Safety warnings

WARNING Read the enclosed safety warnings, the additional safety warnings and the instructions. Failure to follow the safety warnings and the instructions may result in electric shock, fire and/or serious injury. Keep the safety warnings and the instructions for future reference.

The following symbols are used in the user manual or on the product:

Risk of personal injury.

Risk of electric shock.

Immediately remove the mains plug from the mains if the mains cable becomes damaged and during cleaning and maintenance.

Wear safety goggles. Wear hearing protection.

Double insulated.

Additional safety warnings for hammer drills

Do not work materials containing asbestos. Asbestos is considered carcinogenic.

Wear safety goggles, hearing protection and if necessary other protective means, such as safety gloves, safety shoes, etc.

Always hold the machine with two hands.

Make sure that the workpiece is properly • supported or fixed.

Before use, always check walls, floors, or • ceilings for the presence of hidden wiring and pipes.

Only use accessories that are suitable for use • with the machine.

Only use accessories with the correct dimensions.

Inspect the accessories before each use. Do not use accessories which are bent, cracked, or otherwise damaged.

Always use the auxiliary grip to reduce the risk of loss of control. Risk of personal injury.

Hold the machine by the insulated gripping • surfaces where the accessory may contact hidden wiring or the mains cable. If the accessory contacts a ‘live’ wire, the exposed metal parts of the machine can also become ‘live’. Risk of electric shock.

After use, do not touch the tip of the accessory.

Electrical safety

Always check that the voltage of the power supply corresponds to the voltage on the rating plate.

Do not use the machine if the mains cable or the mains plug is damaged.

Only use extension cables that are suitable for the power rating of the machine with a minimum thickness of 1.5 mm^2 . If you use a extension cable reel, always fully unroll the cable.

Mains plug replacement (UK only)

If the moulded 3-pin plug attached to the unit is damaged and needs replacing, it is important that it is correctly destroyed and replaced by an approved BS 1363/13A fused plug and that the following wiring instructions are followed.

The wires in the mains cable are coloured in accordance with the following code:

blue neutral brown live

As the colours of the wires in the mains cable of the unit may not correspond to the coloured markings identifying the terminals in the plug, proceed as follows:

• The wire which is coloured blue must be

connected to the terminal which is marked with the letter N or coloured black.

The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

Technical data

Mains voltage 230V~
Mains frequency 50Hz
Power input 1,500W
No-load speed 350 - 800 /min
Impact rate 1100 - 2700 /min
Max. drilling diameter
Wood 40 mm
Steel 13 mm
Concrete 36 mm
Weight 6 kg
Noise and vibration
Hammer position
Sound pressure (Lpa) 98.5 dB(A)
Acoustic power (Lwa) 109.5 dB(A)
Uncertainty (K) 3 dB(A)
Vibration main handle 19.819 m/s	^2
Uncertainty (K)	1.5 m/s ^2
Hammer/drill position
Sound pressure (Lpa)	96.88 dB(A)
Acoustic power (Lwa)	107.88 dB(A)
Uncertainty (K) 3 dB(A)
Vibration main handle 24.847 m/s	^2
Uncertainty (K)	1.5 m/s ^2

Wear hearing protection.

Vibration level

The vibration emission level stated in this instruction manual has been measured in accordance with a standardised test given in EN 60745; it may be used to compare one tool with another and as a preliminary assessment of exposure to vibration when using the tool for the applications mentioned

• using the tool for different applications, or with different or poorly maintained accessories, may significantly increase the exposure level
• the times when the tool is switched off or when it is running but not actually doing the job, may significantly reduce the exposure level

Protect yourself against the effects of vibration by maintaining the tool and its accessories, keeping your hands warm, and organizing your work patterns

Description

(fig. A)

Your hammer drill has been designed for drilling holes into wood, steel, and masonry. The machine can also be used as a demolition hammer in combination with the SDS chisels.

1. On/off switch
2. Drill selection switch
3. Hammer selection lever
4. Chuck
5. Locking sleeve
6. Main grip
7. Auxiliary grip
8. Depth stop
9. Lubrication point
10. Carbon brush holder
11. Adjusting wheel for electronic speed control

Assembly

Before assembly, always switch off the machine and remove the mains plug from the mains.

Mounting and removing the accessory (fig. B)

Do not use blunt drill bits or chisels. Immediately sharpen or replace blunt drill bits or chisels.

Mounting

• Apply a few drops of oil to the shaft of the accessory.
• Slide the locking sleeve (5) to the rear.
• Insert the accessory into the chuck (4).
• Secure the accessory by turning it counterclockwise until it locks into place.
  • Release the locking sleeve (5).

Removing

• Slide the locking sleeve (5) to the rear.
• Remove the accessory from the chuck (4).
  • Release the locking sleeve (5).

Mounting and removing the auxiliary grip (fig. C)

Mounting

• Loosen the auxiliary grip (7) by turning it counterclockwise.
  • Mount the auxiliary grip (7) by sliding it over

the chuck (4).

Turn the auxiliary grip (7) to the required position.

Tighten the auxiliary grip (7) by turning it • clockwise.

Removing

Loosen the auxiliary grip (7) by turning it • counterclockwise.

Remove the auxiliary grip (7).•

Tighten the auxiliary grip (7) by turning it • clockwise.

Mounting and removing the depth stop (fig. C)

Mounting

Loosen the auxiliary grip (7) by turning it • counterclockwise.

Insert the depth stop (8) through the hole in the auxiliary grip (7).

Set the depth stop (8) to the required position.

Tighten the auxiliary grip (7) by turning it • clockwise.

Removing

Loosen the auxiliary grip (7) by turning it • counterclockwise.

Remove the depth stop (8).

Tighten the auxiliary grip (7) by turning it • clockwise.

Mounting and removing the dust collector (fig. D)

The dust collector prevents dust from entering the machine when drilling into ceilings.

Immediately replace a damaged dust collector.

Mounting

If necessary, remove the accessory from the • chuck (4).

Slide the dust collector (15) over the shaft of the accessory.

Insert the accessory with the dust collector • (15) into the chuck (4).

Removing

Remove the accessory with the dust collector • (15) from the chuck (4).

Remove the dust collector (15) from the accessory.

Use

Switching on and off (fig. A)

• To switch on the machine, press the on/off switch (1).
• To switch off the machine, release the on/off switch (1).

Setting the operating mode (fig. A & E)

The drill selection switch and the hammer selection lever must be set according to the required operating mode. Refer to the table below to set the required operating mode.

Setting (fig. E)	Operating mode
A	Demolition hammer / Chisel
B	Hammer drill
C	Drill

- Turn the drill selection switch (2) and the hammer selection lever (3) to the required position.

Speed Preselection

The required speed can be preselected with the thumbwheel. Also during running the rotational speed can be adjusted.

$$ 1 - 2 = \text { low speed } $$

$$ 3 - 4 = \text { medium speed } $$

$$ 5 - 6 = \text { high speed } $$

$$ \text { Max } = \text { maximum speed } $$

The required speeds depends on the material and can be determined by practical testing.

Hints for optimum use

• Clamp the workpiece. Use a clamping device for small workpieces.
  • Firmly hold the machine by the grip.
• Set the operating mode.
• Switch on the machine.
• Do not apply too much pressure on the machine. Let the machine do the work.
• Switch off the machine and wait for the machine to come to a complete standstill before putting the machine down.

Cleaning and maintenance

Before cleaning and maintenance, always switch off the machine and remove the mains plug from the mains.

Regularly clean the housing with a soft cloth. Keep the ventilation slots free from dust and dirt. If necessary, use a soft, moist cloth to remove dust and dirt from the ventilation slots.

Lubrication

(fig. A)

Regularly grease the shaft in which the • accessories must be inserted.

Regularly check the grease level inside the machine:

Remove the cover from the lubrication • point (9) using a screwdriver.

Remove the cap from the lubrication point • (9).

If necessary, add some grease into the • lubrication point (9).

Mount the cap to the lubrication point (9).•

Mount the cover to the lubrication point (9) • using a screwdriver.

Checking and replacing the carbon • brushes (fig. A)

The carbon brushes must be checked • regularly. If the carbon brushes are worn, the machine will start to run unevenly.

Only use the correct type of carbon brushes.

Remove the carbon brush holders (10) using a • screwdriver.

Clean the carbon brushes.

In case of wear, replace both carbon brushes • at the same time.

- Mount the carbon brush holders (10) using a screwdriver.

• After mounting the new carbon brushes, let the machine run at no load for 15 minutes.

Warranty

Consult the enclosed warranty terms.

Environment

Disposal

The product, the accessories, and the packaging must be sorted for environmentally friendly recycling.

Only for EC countries

Do not dispose of power tools into domestic waste. According to the European Guideline 2002/96/EC for Waste Electrical and Electronic Equipment and its implementation into national right, power tools that are no longer usable must be collected separately and disposed of in an environmentally friendly way.

The product and the user manual are subject to change. Specifications can be changed without further notice.

BOHRHAMMER

1 - 2 = niskie obroty

Spare parts list

HDM1022 - FBH-1500N

Position Description No.

706064 Front selection lever 43 TILL 50
806002 Bearing 52
706065 Big gear 56
800627 Bearing 59
806202 Bearing 65
706066 Rear selection knob 75
806001 Bearing 76
706067 Rotor 77
800608 Bearing 78
706068 Stator 84
706069 Carbon brush holder 89
706070 Carbon brush set 90
706071 Switch 95
706072 Capacitor 100
706073 Speed control 102
706074 Auxiliary handle	104 TILL 109

CE

DECLARATION OF CONFORMITY FBH-1500N, ROTARY HAMMER

(EN) We declare under our sole responsibility that this product is in conformity and accordance with the following standards and regulations:
(DE) Der Hersteller erklärt eigenverantwortlich, dass dieses Produkt den folgenden Standards und Vorschriften entspricht:
(NL) Wij verklaren onder onze volledige verantwoordelijk heid dat dit product voldoet aan, en in overeenstem ming is met, de volgende standaarden en reguleringen:
(FR) Nous déclarons sous notre seule responsabilité que ce produit est conforme aux standards et directives suivants:
(ES) Declaramos bajo nuestra exclusiva responsabilidad que este producto cumple con las siguientes normas y estándares de funcionamiento:
(PT) Declaramos por nossa total responsabilidade de que este produto está em conformidade e cumpre as normas e regulamentações que se seguem:
(IT) Dichiariamo, sotto la nostra responsabilità, che questo prodotto è conforme alle normative e ai regolamenti seguenti:
(SV) Vi garanterar på eget ansvar att denna produkt upp fyller och följer följande standarder och bestämmelser:
(FI) Vakuutamme yksinomaan omalla vastuullamme, että tämä tuote täyttää seuraavat standardit ja säädökset:
(NO) Vi erklærer under vårt eget ansvar at dette produktet er i samsvar med følgende standarder og regler:
(DA) Vi erklærer under eget ansvar, at dette produkt er i overensstemmelse med følgende standarder og bestemmelser:
(HU) Felelősségünk teljes tudatában kijelentjük, hogy ez a termék teljes mértékben megfelel az alábbi szabványoknak és előírásoknak:

(CS) Na naši vlastní zodpovědnost prohlašujeme, že je tento výrobek v souladu s následujícími standardy a normami:
(SK) Vyhlasujeme na našu výhradnú zodpovednosť, že tento výrobok je v zhode a súlade s nasledujúcimi normami a predpismi:
(SL) S polno odgovornostjo izjavljamo, da je ta izdelek v skladu in da odgovarja naslednjim standardom terpredpisom:
(PL) Deklarujemy na własną odpowiedzialność, że ten produkt spełnia wymogi zawarte w następujących normach i przepisach:
(LT) Prisiimdami visą atsakomybę deklaruojame, kad šis gaminys atitinka žemiau paminėtus standartus arba nuostatus:
(LV) Apgalvojam ar visu atbildību, ka šis produkts ir saskaņā un atbilst sekojošiem standartiem un nolikumiem:
(ET) Deklareerime meie ainuvastutusel, et see toode on vastavuses ja kooskõlas järgmiste standardite ja määrustega:
(RO) Declarăm prin aceasta cu răspunderea deplină că produsul acesta este în conformitate cu următoarele standarde sau directive:
(HR) Izjavljujemo pod vlastitom odgovornošu da je strojem ukladan sa slijedešim standardima ili standardiziranim dokumentima i u skladu sa odredbama:
(SR) Pod punom odgovornošću izjavljujemo da je usaglašen sa sledećim standardima ili normama:
(RU) Под свою ответственность заявляем, что данное изделие соответствует следующим стандартам и нормам:
(UK) На свою власну відповідальність заявляємо, що дане обладнання відповідає наступним стандартам і нормативам:
(EL) Δηλώνουμε υπεύθυνα ότι το προϊόν αυτό συμφωνεί και τηρεί τους παρακάτω κανονισμούς και πρότυπα:

EN 55014-1, EN 55014-2, EN 60745-1, EN 60745-2-6, EN 61000-3-2, EN 61000-3-3

2006/42/EC, 2006/95/EC, 2004/108/EC, 2002/96/EC, 2006/95/EC

Zwolle, 01-12-2010

J.A. Bakker-van Ingen CEO Ferm BV

It is our policy to continuously improve our products and we therefore reserve the right to change the product specification without prior notice.

Ferm BV • Lingenstraat 6 • 8028 PM • Zwolle The Netherlands