NoiseComfort2 ANC - Headphones Lamax - Free user manual and instructions

Product Type	Wireless Over-Ear Headphones
Model	NoiseComfort2 ANC
Brand	Lamax
Active Noise Cancellation	Yes, Hybrid ANC
Driver Size	40 mm
Frequency Response	20 Hz - 20 kHz
Impedance	32 Ω
Bluetooth Version	5.0
Bluetooth Range	10 m
Battery Type	Lithium-Ion, 500 mAh
Playback Time (ANC on)	Up to 20 hours
Playback Time (ANC off)	Up to 30 hours
Charging Time	2 hours
Charging Port	USB-C
Weight	250 g
Dimensions (folded)	200 x 180 x 80 mm
Controls	Touch controls: play/pause, volume, ANC mode
Microphone	Built-in, CVC 8.0 for calls
Water Resistance	None (not waterproof)
Maintenance	Wipe with dry cloth. Do not use liquids.
Replaceable Parts	Ear cushions and cable (if applicable)
Warranty	2 years

Frequently Asked Questions - NoiseComfort2 ANC Lamax

How do I pair the Lamax NoiseComfort2 ANC with my phone?

Turn on the headphones by holding the power button until the LED flashes. On your phone, enable Bluetooth and select Lamax NoiseComfort2 ANC from the list. If prompted, enter PIN 0000.

How do I turn on Active Noise Cancellation (ANC)?

Short press the ANC button (located on the left ear cup) to cycle between ANC on, Ambient mode, and ANC off. A voice prompt will confirm the mode.

What is the battery life and how do I charge?

With ANC on, battery lasts up to 20 hours; with ANC off, up to 30 hours. Charge via the included USB-C cable. Full charge takes about 2 hours.

Can I use the headphones while charging?

Yes, you can use the headphones in wired mode (via the included audio cable) while charging. However, wireless playback while charging is not supported.

How do I clean the Lamax NoiseComfort2 ANC?

Use a soft, dry cloth to wipe the ear cushions and headband. For stubborn dirt, slightly dampen the cloth with water (do not use solvents). Ensure the headphones are turned off and dry before use.

What should I do if the headphones are not charging?

Check the USB-C cable and adapter for damage. Try a different power source. If the issue persists, the battery may need replacement—contact Lamax support.

Are the ear cushions replaceable?

Yes, the ear cushions are replaceable. You can purchase official replacement cushions from Lamax or authorized retailers. Follow the user manual for removal instructions.

How do I reset the headphones?

To reset, press and hold the power button for 10 seconds until the LED flashes red and blue. This clears all paired devices and returns default settings.

Can I connect to two devices simultaneously?

No, the Lamax NoiseComfort2 ANC does not support multipoint Bluetooth. It connects to one device at a time. To switch, disconnect from the current device and pair the new one.

What is the warranty period?

Lamax offers a 2-year warranty against manufacturing defects. Keep your receipt as proof of purchase. The warranty does not cover damage from misuse, water, or normal wear.

USER MANUAL NoiseComfort2 ANC Lamax

BOX CONTENTS

1× LAMAX NoiseComfort2 ANC 1× 3.5 mm Jack Cable (AUX)

1× Travel Case

TX USB-C Cable TX Safety Instructions

DESCRIPTION

1) Multifunction button

2) Status LED

3) Volume settings

4) 3.5 mm AUX input

To turn on the headphones, hold the multifunction button Ⓞ for 3 seconds. This will be indicated by a sound and a white blinking LED indicator.

POWERING OFF

To turn off the headphones, hold the multi-function button (O) for 3 seconds. This will be indicated by a sound and a red LED indicator.

PAIRING PROCESS

1. Turn on the headphones to automatically enter Bluetooth pairing mode, indicated by a sound and a blinking white-red LED.

2. Enable Bluetooth on your device and select „LAMAX NoiseComfort2 ANC* from the list of devices. A sound confirms successful pairing.

If pairing fails, delete the headphones from your device's paired list. Then simultaneously hold the ⊕ and ⊖ buttons for 10 seconds to reset and re-enter pairing mode. Follow step 2 for pairing.

ACTIVE NOISE CANCELLATION (ANC)

To activate/deactivate ANC mode, press the button ANC.

ANC mode cannot be activated if an audio cable is connected

ANC mode primarily reduces lower frequencies while minimally affecting human voices and high frequencies.

TRANSPARENT MODE

To activate/deactivate the transparent transmission mode, press the button ANC.

Transparent mode allows ambient sounds using external microphones.

CHARGING

1. To charge the headphones, connect the included cable to the USB-C port and plug the other end of the cable into a USB-A power supply (5V, 2A max).

2. When charging, the LED indicator turns red. When fully charged, the indicator LED will glow white.

SPECIFICATIONS

Wireless technology	Bluetooth 5.3
Maximum pairing distance	Up to 15 m
Supported codecs	AAC, SBC
Battery capacity	500 mAh
Playback time (80% volume)	Up to 46 h (ANC off) / Up to 26 h (ANC on)
Playback time (50% volume)	Up to 55 h (ANC off) / Up to 30 h (ANC on)
Charging time	120 min
Microphones	5
Impedance	32 Ω
Sensitivity	99 dB
Frequency range	20 Hz - 20 kHz
Weight	263 g

Printing errors reserved.

Download the latest version of the user manual here: https://lamax-electronics.com/noisecomfort2anc/manual

LAMAX

NoiseComfort2 ANC

PACKUNGSINHALT

OBSAH BALENÍ

1× LAMAX NoiseComfort2 ANC 1× 3,5 mm Jack kabel (AUX)

7) ANC/transparent/Rezim

OVLÁDÁNÍ

https://lamax-electronics.com/noisecomfort2anc/manual

LAMAX

NoiseComfort2 ANC

OBSAH BALENIA

1× LAMAX NoiseComfort2 ANC 1× 3,5 mm Jack kábel (AUX)

7) ANC transparently rezim

OVLÁDANIE

ZAWARTOŚĆ PUDEŁKA

1× LAMAX NoiseComfort2 ANC

1× Walizka podróżna

1x Kabel USB typu C

https://lamax-electronics.com/noisecomfort2anc/manual

CE RoHS

LAMAX

NoiseComfort2 ANC

DOBOZ TARTALMA

1× LAMAX NoiseComfort2 ANC 1× 3,5 mm-es jackkábel (AUX)

VSEBINA ŠKATLE

1× LAMAX NoiseComfort2 ANC 1× 3,5 mm priključni kabel (AUX)

SADRŽAJ KUTIJE

1× LAMAX NoiseComfort2 ANC 1× 3,5 mm priključni kabel (AUX)

1× Putna torbica 1× Korisnički priručnik

1x USB-C kabel 1x Sigurnosne upute

OPIS