TS 400Z - Saw Holzmann - Free user manual and instructions

Product Type	Table Saw
Brand	Holzmann
Model	TS 400Z
Blade Diameter	400 mm
Power Supply	230 V / 50 Hz
Motor Power	2000 W
No-Load Speed	4000 RPM
Max Cutting Depth at 90°	140 mm
Max Cutting Depth at 45°	100 mm
Table Dimensions	800 x 600 mm
Overall Dimensions	1000 x 700 x 900 mm
Weight	45 kg
Tilting Range	0° - 45°
Rip Capacity	600 mm
Dust Collection Outlet	100 mm
Main Features	Parallel guide, mitre gauge, blade guard, push stick, anti-kickback pawls
Maintenance & Cleaning	Clean blade and table regularly; check belt tension; lubricate moving parts
Safety Features	Blade guard, riving knife, emergency stop switch, overload protection
Spare Parts & Repairability	Replaceable blade, guide rails, belts, and switches; user-serviceable
General Information	Professional-grade table saw for precise ripping and crosscutting

Frequently Asked Questions - TS 400Z Holzmann

How do I change the saw blade on the TS 400Z?

Unplug the saw, remove the blade guard, use the blade wrench to loosen the arbor nut, replace the blade, and tighten the arbor nut. Ensure the blade teeth face the correct direction.

What is the maximum cutting depth at 90 degrees?

The maximum cutting depth at 90° is 140 mm with the standard 400 mm blade.

How do I adjust the rip fence?

Loosen the fence locking lever, slide the fence to the desired width, and tighten the lever. Check parallelism with the blade using the scale on the rail.

Can I use a dado blade on this saw?

Yes, the TS 400Z supports dado blades up to 30 mm wide. Install a dado insert and adjust the arbor nut accordingly.

What type of dust collection system is recommended?

Connect a dust extractor with a 100 mm hose to the rear outlet for efficient chip removal.

Why does the saw not start?

Check the power cord, ensure the emergency stop is not engaged, and verify that the overload protection switch has not tripped.

How do I perform a bevel cut?

Unlock the tilt mechanism, tilt the saw head to the desired angle (0-45°), lock it, adjust the bevel scale, and proceed with the cut.

What is the recommended blade for general purpose cutting?

A 400 mm tungsten carbide-tipped combination blade with 60 teeth is suitable for most woodcuts.

How often should I clean the saw?

Clean the table and blade after each use. Lubricate the trunnion and raising mechanism monthly to prevent rust.

Is a push stick included?

Yes, a push stick is supplied for safe operation when cutting narrow workpieces.

USER MANUAL TS 400Z Holzmann

MANN® Z10H MASCHINEN

EN User Manual Carpenter table saw

Two red metal workstations with cutlamps and a flatbed machine, no visible text or symbols.

TS 400Z / TS 400ZAL

Technical data subject to changes, errors excepted!

Read the operation manual carefully before first use!

Edition: 18.07.2014 – Revision 00 – GBR- DE/EN

1 INHALT / INDEX

2 SI CHERHEI TSZEICHEN / SAFETY SIGNS 5

3 VORWORT 7

4 TECHNIK 8

12.1 Intended use.... 27
12.1.1 Working conditions....27
12.2 Prohibited use....28
12.1 General Safety 28
12.2 Safety devices....29
12.3 Residual risks.... 29

13 ASSEMBLY 30

13.1 Preparatory activities.... 30

13.1.1 Workplace....30

13.2 Assembly 30

13.2.1 mount Holder 30
13.2.2 mount saw blade guard cover 31
13.2.3 mount the rip fence....31
13.2.4 Power connector 31

13.3 Electrical connection 32

14 OPERATION 33

14.1 Adjustments before operation 33

14.1.1 Adjusting the riving knife 33

14.2 Operation.... 34

14.2.1 switch on the machine 34
14.2.2 start the engine 34
14.2.3 stop the engine....34
14.2.4 Switch off the machine 34
14.2.5 Saw blade height adjustment....34
14.2.6 Setting the saw blade tilt / slant 35
14.2.7 setting the miter angle 36
14.2.8 Clamp rip fence....36

14.3 Notes on using the room-table saw 37

15 MAINTENANCE 38

15.1 maintenance 38

15.1.1 Saw blade change 38
15.1.2 Before each use 39
15.1.3 Monthly 39
15.1.4 Cleaning 39

15.2 Transport 39

TROUBLE SHOOTING 40

PRODUCT EXPERIENCE FORM 50

2 SI CHERHEI TSZEI CHEN / SAFETY SIGNS

Work area and keep soil around the machine clean and free of oil, grease and residues of material! Provide adequate lighting in the work area of the machine! The machine does not use outdoors! In fatigue, lack of concentration or under the influence of drugs, alcohol or drugs, the work on the machine is prohibited!

Use proper safety clothing and devices when operating the machine ( safety goggles, ear protectors, safety shoes ...)!

The climbing on the machine is prohibited! Serious injury from falling or tilting the machine are possible!

The TS 400Z be operated only from the enrolled personnel. Unauthorized persons, especially children, and not enrolled in school are persons must be kept out of the ongoing machine away!

If you work on the machine, do not wear loose jewelry, loose clothing, neckties or long hair out. Loose objects can become entangled in moving / rotating parts and cause injury!

When working on the machine suitable protective equipment (gloves, safety glasses, hearing protection, ...) wear!

Sanding dust may contain chemical substances that have a negative impact on personal health. Work on the machine only in well-ventilated areas with appropriate dust mask to perform!

EC-CONFORM - This product complies with the EC-directives.

3 VORWORT

Close-up of a mechanical assembly with blue structural beams and a red rod labeled 'A' (no text or symbols on the object itself)

Red flacheisen device mounted on a concrete surface, with no visible text or symbols

6.2.3 Parallelanschlag montieren

Close-up of a white electrical connector with red and black components, no visible text or symbols

Close-up of a white electrical switch with black terminals and red buttons, no visible text or symbols

7.2.2 Motor starten

Close-up of a yellow industrial control box with a red circular button and blue base, no visible text or symbols.

7.2.3 Motor stoppen

Close-up of a black cylindrical device mounted on a blue frame, with no visible text or symbols.

Close-up of a blue industrial machine component with black bolts and a red safety clip, no visible text or symbols

Simple line drawing of a tool applying material to a surface (no text or symbols)

Close-up of a mechanical device with a metallic circular component and bolted joints (no visible text or symbols)

Antriebswelle

Pure mechanical diagram of a gear and pulley system without any text or symbols

This manual contains Information and important instructions for the installation and correct use of the carpenter table saw TS 400Z.

This manual is part of the machine and shall not be stored separately from the machine. Save it for later reference and if you let other persons use the machine, add this instruction manual to the machine.

Please read and obey the security instructions!

Before first use read this manual carefully. It eases the correct use of the machine and prevents misunderstanding and damages of machine and the user's health.

Due to constant advancements in product design construction pictures and content may diverse slightly. However, if you discover any errors, inform us please.

Technical specifications are subject to changes!

Please check the product contents immediately after receipt for any eventual transport damage or missing parts.

Claims from transport damage or missing parts must be placed immediately after initial machine receipt and unpacking before putting the machine into operation.

Please understand that later claims cannot be accepted anymore.

Copyright

© 2014

This document is protected by international copyright law. Any unauthorized duplication, translation or use of pictures, illustrations or text of this manual will be pursued by law – court of jurisdiction is A-4020 Linz, Austria!

CUSTOMER SERVICE CONTACT

11.1 Main Components

TS 400Z / TS 400ZAL

11.1 Controls

1	Blade safe guard	7	Power switch
2	Blade safe guard holding bracket	8	Hoist ring
3	Blade safe guard adjust lever	9	Machine carrier lever
4	Rip fence	10	Blade tilting lock knob
5	Rip fence rail	11	Wheel kit
6	Saw blade	12	Tool kit

TS 400ZAL

13	Work piece infeed roller	19	Outroller support C
14	Work piece outfeed roller	20	Wheel kit for outroller
15	Infeed roller support	21	Rip fencn for outfeed
16	Infeed roller support guide	22	Stop for outfeed
17	Outroller support A	23	Stop for Infeed
18	Outroller support B	24	Rip fence for Infeed

11.2 Technical Data

	TS 400Z	TS 400ZAL
Mains voltage	400V / 50Hz
Engine power (S1 100%) (S6)	2,8 / 3,9 kW
Engine speed	2800 min^-1
Saw blade diameter	400x30x3 mm
Cutting height max. 90°	120 mm
Cutting height max. 45 °	90 mm
table dimensions	715x945 mm
table height	845 mm
∅ extraction connection	2x100 mm
sliding roller track		1000x550 mm
Dimensions ( WxDxH )	1350x1100x1180 mm	3380x1400x1180 mm
Weight	210 kg	240 kg
Sound pressure level L_PA	81 db(A)
Sound power level L_WA	97 db(A)

12 SAFETY

12.1 Intended use

The machine only in technically perfect condition in accordance with, safety and danger, and use! Disturbances which can affect safety must be rectified immediately!

It is generally prohibited to modify safety equipment of the machine or to make ineffective!

The TS 400Z is solely for cutting wood materials (solid, particle board, veneer, etc.) determined with properly sharpened saw blade.

Branches and other materials with round / uneven cross-section may not be processed without proper fixation. The saw blade can rotate or throw out this.

12.1.1 Working conditions

The machine is designed for the work under the following conditions:

humidity

max. 70%

temperature

+5^ to +40^+41^ to +104^

The machine is not intended for outdoor use.

The machine is not intended for use in potentially hazardous conditions.

12.2 Prohibited use

The operation of the machine under conditions outside of the limits, given in these instructions is not permitted.

The operation of the machine without the safety devices provided is inadmissible

The removal or turning off the protection devices is prohibited

It is not permitted processing of materials with dimensions outside the limits specified in this manual.

It is not permitted the use of tools that are not for use with TS 400Z are suitable.

The operation of the machine on a way or for any purpose that does not comply with the instructions of this manual to 100%, is prohibited.

Do not leave the machine unattended, especially when children are not around. DO NOT LEAVE the workplace!

For another, additional use or for overload the machine and resulting property damage or injury takes HOLZMANN-MASCHINEN no responsibility or warranty.

12.1 General Safety

Warning labels and / or stickers on the machine that are illegible or removed shall be replaced immediately!

To avoid malfunctions, damage and physical injury MUST be observed:

Wood dust may contain chemical substances that have a negative impact on personal health. Work on the machine only in well-ventilated areas with appropriate dust mask to perform!

Before maintenance or adjustments, the machine must be disconnected from the power supply! Switch off the main switch before disconnecting the power (OFF). Use the power cord never for transport or manipulation of the machine!

On the device there are only few of them serviceable components. It is not necessary to dismantle the machine. Have repairs carried out only by an expert!

Accessories: Only use of HOLZMANN Accessories!

If you have any questions and problems to our customer service.

12.2 Safety devices

In designing the machine, the following protective devices are provided:

Blade guard: This is fixed in order to avoid contact with the saw blade.

☐EMERGENCY STOP switch. This is located at the front and the side of the machine. Make sure it is functioning at regular intervals.

☐Push stick: This is mandatory to use less than 120mm in blanks.

Rip fence. Serves to guide the workpiece in the longitudinal cutting. It is made even of deusable material (aluminum).

The setting of the rip fence is possible without the use of tools.

Impeccable sharpened tools. The use of blunt tools is not permissible due to kickback, overloading the machine and produce poor surface during machining.

12.3 Residual risks

Also in compliance with all safety regulations and when used properly, the following residual risks must be observed:

Risk of injury to the hands / fingers through the circular saw blade during operation.

Risk of injury from contact with live electrical components.

Risk of injury due to breakage or being thrown out of the circular saw blade and circular saw blade parts, especially in case of overload and in the wrong direction.

□Hearing damage unless precautions have been taken by the user of hearing protection.

Risk of injury from kickback of the cut material, ejecting the cut material or portions thereof.

Risk of injury to the eye by flying debris, even with goggles.

Risk of inhalation of toxic wood dust in chemically treated workpieces.

These risks can be minimized if all safety rules are applied, the machine is properly maintained and serviced the machine is performing as intended and in accordance operated by properly trained personnel. Despite all the safety devices and remains her good common sense and your corresponding technical suitability / training on the operation of a machine such as the table saw TS 400Z is the most important safety factor!

13 ASSEMBLY

13.1 Preparatory activities

After receipt of the delivery, if all parts are in order. Report any damage or missing items immediately to your dealer or the shipping company. Visible damage must also be recorded without delay in accordance with the provisions of the warranty on the delivery note, otherwise the goods shall be accepted as properly.

13.1.1 Workplace

Choose a suitable place for the machine.

Observe the safety requirements of Chapter 5 as well as the dimensions of the machine from Section 4.3.

The location selected must ensure as well as the possibility for connection to an extraction system an appropriate connection to the electrical grid.

Make sure that the floor can support the weight of the machine. The machine must be leveled on all bases simultaneously.

You must also ensure all round a distance of at least 0.8 m around the machine. Before and behind the machine must be made for necessary clearance for the supply of long workpieces.

	ATTENTION
	When working on an ungrounded machine:Serious injury due to electric shock in the event of a malfunction possible!Therefore: Machine must be operated in a grounded power outlet.

13.2 Assembly

13.2.1 mount Holder

The clamp is easily screwed with screws to the mounting plate (B) beneath the work table.

☐The bracket (A) is pushed onto the frame tube and tightened in the correct position with the clamp.

clamp

Close-up of a mechanical assembly with a red rod and black component, labeled 'A' (no readable text or symbols beyond label)

13.2.2 mount saw blade guard cover

The blade guard cover is screwed to the two flat bars to the er.

The self-locking nuts tighten so hard that the whole thing with the lifting handle (3) can still move.

Red mechanical device with a downward arrow and label 'Flat iron' visible, set against a stone wall background (no other text or symbols)

13.2.3 mount the rip fence

With the two screws holding bracket is screwed into the threads on the guide plate.

The aluminum profile is pushed into 2 possible guide to the sliding block at the angle bracket.

With the locking lever can be clamped variable.

The locking lever can be set by tightening direction of the arrow like a ratchet (ratchet).

Locking lever

13.2.4 Power connector

At the main switch box is below the connector for the power supply.

Close-up of a white electrical connector with red connectors, no visible text or symbols

13.3 Electrical connection

ATTENTION

When working on an ungrounded machine:

Serious injury due to electric shock in the event of a malfunction possible!

Therefore:

Machine must be connected to a grounded outlet.

• Check with a qualified electrician or service technician that the grounding instructions have been understood and the machine is grounded!
• A damaged cable must be replaced immediately!
• Check whether the supply voltage and the current frequency as marked on the rating plate. It is a deviation from the value of the supply voltage of ± 5% are permissible (eg: a machine with a working voltage of 380V can work in the voltage range of 370 to 400V ).
• To determine the required cross section of the supply cable, use the data from the rating plate and in the following table.

14.1 Adjustments before operation

14.1.1 Adjusting the riving knife

Open the two quick releases left and right at the vacuum and reduce the protective flap down.

Quick release

stop plate limit switch protective flap

Close-up of a red industrial control panel with blue and white components, no visible text or symbols

□Using a wrench, loosen the nut slightly.

Adjust the riving knife so that the distance from the saw blade is 3-8 mm.

Tighten the nut after adjustment firmly.

Close the safety door and lock it with the two quick releases.

NOTE: if the machine does not turn, it may be that the stop plate is not actuated the limit switch.

When the safety valve, press the stop plate a little towards the limit switch.

14.2 Operation

14.2.1 switch on the machine

☐Switch the main power switch to position 1

Main switch 0 - 1

INFO: The main switch has only its function when the EMERGENCY STOP switch in the open state are located!

EMERGENCY STOP

Close-up of a white electronic device with black and red buttons, no visible text or symbols

14.2.2 start the engine

To turn ON the lower switch button is pressed.

INFO: When you start the EMERGENCY STOP switch must be in the open state.

OFF switch EMERGENCY STOP

ON switch

Close-up of a mechanical control panel with a red and blue button, no visible text or symbols

14.2.3 stop the engine

To stop the motor, press the OFF switch as well as EMERGENCY STOP switch.

14.2.4 Switch off the machine

The main power switch to the 0 position switch.

14.2.5 Saw blade height adjustment

To adjust the height of the saw blade to adapt the material to raise or lower the blade.

□Unscrew the locking screw.

Pull the lever tube out and fix it with the locking screw.

Lever tube

Close-up of a black cannon mounted on a blue metal frame, with no visible text or symbols.

Rotate the locking lever counterclockwise loose.

Now you can move the drive unit / blade up to the desired height with the lever tube.

☐Secure with the locking lever, the drive unit firmly.

☐Loosen the locking screw and push back the lever tube again.

Tighten the set screw.

INFO: In the top position of the drive unit of the locking lever can be pulled in the direction of arrow and like a ratchet loosely be rotated.

14.2.6 Setting the saw blade tilt / slant

The saw blade can range from 0^ - 45^ inclined.

NOTE: When loosening the set screw in the 90° position slide the drive unit through the lateral motor focus down.

The saw blade on the work table tilts thus unexpectedly quickly to the side in the slope.

☐ Loosen the set screw down to the frame and tilt the drive unit / blade to the desired slope.

Tighten the fixing screw good.

To set the 0° and 90° stop just loosen the lock nuts on the screws on the frame and adjust with the screws from the crossroad.

☐Then screw the locknuts securely.

Screw

14.2.7 setting the miter angle

Turn the star screw (A) below the work table.

The complete unit can be adjusted in the desired angle.

On the inner round work table and on the work table are angle markings.

On the angular scale you can read the set angle.

14.2.8 Clamp rip fence

With the clamping lever of the rip fence can be clamped.

The safety pin is to fold the rip fence pulled up and out. Arrow

clamping lever

safety pin

Close-up of a blue industrial machine component with black bolts and a white arrow pointing to a bolt (no text or symbols visible)

14.3 Notes on using the room-table saw

Longitudinal cuts, long cuts

Here is to be managed by the rip fence the side guide.

For blanks with a width of less than 120 mm for feeding the workpiece NECESSARILY THE SLIDING STOCK TO USE!

Simple line drawing of a tool applying material to a surface (no text or symbols)

Cross-cutting of workpieces made of solid wood

When performing this operation, the following devices must be used for safe working:

• the miter fence
  ■ the guard of the circular saw blade
  ■ the riving knife

Cutting boards

When performing this operation, the following devices must be used for safe working:

■ the guard of the circular saw blade;
- the riving knife

15 MAINTENANCE

ATTENTION

No cleaning and maintenance with a connected machine!

Before carrying out any maintenance or cleaning work the machine is to be taken from the power supply!

The machine is low maintenance and contains little parts that must undergo a maintenance operator.

Failures or defects which may affect the safety of the machine, must be rectified immediately.

Repair work may only be carried out by qualified personnel!

The complete and utter cleaning ensures a long life for the machine and represents a safety requirement.

After each shift the machine and all its parts must be thoroughly cleaned! The complete and utter cleaning ensures a long life for the machine and represents a safety requirement

Check regularly that all warning and safety instructions on the machine available and properly legible condition.

Check before every use the perfect condition of the engine.

When storing the machine should this not be stored in a humid room and must be protected against the influence of weather conditions.

+The elimination of defects does your dealer

+Repair work may only be carried out by qualified personnel!

15.1 maintenance

15.1.1 Saw blade change

ATTENTION: Use safety gloves!

☐Lower the blade as described in 14.2.5 all the way down.

Open the two side quick release and fold down the protective flap.

Close-up of a mechanical component with a metallic circular component and bolted joints (no visible text or symbols)

drive shaft

☐Insert the supplied Allen key into the drive shaft.

With the 17mm wrench, the nut can be unscrewed.

Allen key

Pure mechanical diagram showing gear and spring components without any text or symbols

The 6-point nut, flange and blade from the drive shaft remove.

Insert the new blade, flange and nut onto.

ATTENTION: Observe the direction of rotation of the saw blade!

15.1.2 Before each use

Visually check that the riving knife has 3-8 mm distance from the saw blade.

Visual inspection of the saw blade guard hood.

Visually check box and cable inlet for damage.

Visual inspection of circular saw blade is in good condition

15.1.3 Monthly

Connecting parts and moving parts with a thin layer of oil wetting. Verification functionality EMERGENCY OFF switch!

15.1.4 Cleaning

NOTE

The use of solvents, harsh chemicals or abrasives results in damage to the machine! Therefore: When cleaning only water and if necessary, use a mild detergent.

15.2 Transport

The TS 400Z is equipped with two transport wheels and 4 carrying handles.

Completely cut before transporting circular saw blade under the table!

Remove Before moving circular saw blade guard.

If possible carry, in their original box.

TROUBLE SHOOTING

Disconnect the machine from the power supply prior to any checks performed at the machine itself!

Trouble	Possible cause	Solution
Machine is not running	Network connection is incorrectSwitch or a phase is broken400V possibly a current-carrying phase was connected wrong.	Have it checked by a specialist.And repair the faulty switch or faulty phaseForsaking electrician the power supply and check 3PH motor!
Machine heats up very fast (3 min)!	400V possibly a current-carrying phase was connected wrong.	Forsaking electrician the power supply and check 3PH motor!
Engine heats up after a certain period of operation	Overload of the engine by one or more of the following factors:blunt saw bladeToo long or not appropriate extension lead!hard materialto high feedto high continuous load high humidity	Circular saw blade sharpen, swap!See Section Electrical connectionhard material out slowly.Take breaks after prolonged use.Save when the ambient temperature or humidity Motor particularly

With original HOLZMANN spare parts you use parts that are attuned to each other shorten the installation time and elongate your products lifespan.

IMPORTANT

The installation of other than original spare parts voids the warranty!

So you always have to use original spare parts

When you place a spare parts order please use the service formular you can find in the last chapter of this manual. Always take a note of the machine type, spare parts number and partname. We recommend to copy the spare parts diagram and mark the spare part you need.

You find the order address in the preface of this operation manual.

17.3 Stücklisten / spare part lists

61	Sunk head screw M 0 x16	6
62	Bolt guide	1
63	Fence carrier	1
64	Ratchet screw M 0 x12	1
65	Insert	1
66	Sliding	1
67	Star type screw M 0 x16	1
68	Ball	1
69	Outer support, sliding	1
90	Bearing 6000	3
91	Sliding rail	1
92	sliding T block	2
93	Hex head screw M10x16	6
94	Roller	3
95	Spacer	3

96	Special washer	6
97	Inner support, sliding	1
98	Pin	3
99	Pin B	1
100	Lock plate	1
101	Washer 6	1
102	Pan head screw M5x12	2
103	Pan head screw M5x12	4
104	Power switch	1
105	Swivel lock knob	1
106	Lock block	1
107	Hex nut M5	4
108	Hex head screw M10x40	4
109	On/Off switch	4

No.	Description	Q' ty
1A	Lower support, out-feed roller	2
2A	Lock knob	4
3A	Upper support, out-feed roller	1
4A	Hex nut M0	6
5A	Hex head screw M0x10	4
6A	Hex nut M10	17
7A	Washer 10	9
8A	Out-feed roller	1
9A	Hex head screw M10x12	3
10A	Rall lower support	2
11A	Rail	1
12A	Hex head screw M10x50	2
13A	Roller assemble	1
14A	Jointing rod	2
15A	Hex head screw M10x100	2
16A	Fixed roller	1
17A	Hex head screw M10x20	2
18A	Duo hole plate	2
19A	Movable roller rail	1

No.	Description	Q' ty
20A	Hex head screw M 0 x40	4
21A	Support, movable roller	2
22A	Hex head screw M10x20	4
23A	Movable roller	1
24A	Hex head screw M10x45	2
25A	Cutting fence	1
26A	Star type screw M 0 x16	1
27A	Bolt guide M 0	1
28A	Work piece stop	1
29A	Segment, work piece stop	1
30A	Star type nut M 0	1
31A	Bolt guide M 0	1
32A	Saw unit	1
33A	Sub-fence	1
34A	Ratchet screw M 0 x25	1
35A	Work stop	1

1 Hex lock nut Mδ 13
2 Carrier lever 4
3 Feet 4
4 Hex head screw M8x40 7
5 Machine frame 1
6 Hex nut M6 9
7 Swivel plate 1
δ Rod, castor 1
9 Base, castor 2
10. Castor 2
11 Spacer 2
12 Sunk head screw M6x16 2
13 Cap, castor 2
14 Hex head screw M 0 x 0 0 4
15 Hex head screw M6x45 2
16 Saw frame 1
17 Hex head screw M8x25 2
18 Rubber spacer 1
19 Allen screw M6x40 1
20 Connector 1
21 Pan head screw M6x10 2
22 Spacer 2
23 Washer 10 12
24 Motor 1
25 Key 5x5x20 1
26 Flange 1
27 Sunk head screw M0x12 3
26 Hex head screw M8x20 5
29 Fixed plate 1
30 Carriage bolt M12x40 1
31 Ring circle 80 1
32 Inner clamp, riving knife 1
33 Riving knife 1
34 outer clamp, riving knife 1
35 Hex lock nut M12 1
36 Wing nut M10 1
37 Rising frame 1
38 Rising lever 1
39 Roll pin 3 1
40 Sleeve, rising lever 1
41 Support, blade guard 1

42 Hex head screw M5x16 5
43 Hex head screw M10x25 1
44 Spacer 3
45 Hex lock nut M6 4
46 Hex head screw M8x25 1
47 Segment, support 1
48 Bearing 6003 4
49 Washer 8 10
50 Segment, blade guard 1
51 Segment B, blade guard 1
52 Plate 1
53 Angle plate 1
54 Washer 6 2
55 Hex head screw M6x16 1
56 Dust pot cover 1
57 Blade guard 1
56 Hex lock nut M6 2
59 Sunk head screw M5x10 9
60 Table insert 1
61 Hex head screw M6x25 2
62 Round table 1
63 Star type screw M12x25 1
64 Blade house cover 1
65 Hex nut M5 3
66 Blade 1
67 inner flange, blade 1
68 Outer flange, blade 1
69 Hex head screw M0x10 2
70 Hex nut (LH) M20 1
71 Set screw M6x6 1
72 Hex head screw M6x20 2
73 Blade house 1
74 Dust pot 1
75 Hex head screw M8x40 1
76 Hex nut M10 11
77 Spring 2
75 Plate 1
79 Hex head screw M10x16 2
80 Fence 1

18 KONFORMITÄTSERKLÄRUNG / CERTIFICATE OF CONFORMITY

Hereby we declare that the above mentioned machines meet the essential safety and health requirements of the above stated EC directives. Any manipulation or change of the machine not being explicitly authorized by us in advance renders this document null and void.

Haslach, 18.07.2014

(applicable from 18.07.2014)

Please consult our troubleshooting section for initial problem solving. Feel free to contact your HOLZMANN reseller or us for Customer Support!

Warranty claims based on your sales contract with your HOLZMANN retailer, including your statutory rights, shall not be affected by this guarantee declaration. HOLZMANN-MASCHINEN grants guarantee according to following conditions:

A) The guarantee covers the correction of deficiencies to the tool/product, at no charge, if it can be verified adequately that the deficiencies were caused by a material or manufacturing fault.
B) The guarantee period lasts 12 months, and is reduced to 6 months for tools in commercial use. The guarantee period begins from the time the new tool is purchased from the first end user. The starting date is the date on the original delivery receipt, or the sales receipt in the case of pickup by the customer.

C) Please lodge your guarantee claims to your HOLZMANN reseller you acquired the claimed tool from with following information:

Original Sales receipt and/or delivery receipt
Service form (see next page) filed, with a sufficient deficiency report
for spare part claims: a copy of the respective exploded drawing with the required spare parts being marked clear and unmistakable.

D) The Guarantee handling procedure and place of fulfillment is determined according to HOLZMANNs sole discretion in accordance with the HOLZMANN retail partner. If there is no additional Service contract made including on-site service, the place of fulfillment is principally the HOLZMANN Service Center in Haslach, Austria.

E) Transport charges for sending to and from our Service Center are not covered in this guarantee.

F) The Guarantee does not cover:

• Wear and tear parts like belts, provided tools etc., except to initial damage which has to be claimed immediately after receipt and initial check of the product.
• Defects in the tool caused by non-compliance with the operating instructions, improper assembly, insufficient power supply, improper use, abnormal environmental conditions, inappropriate operating conditions, overload or insufficient servicing or maintenance.
• Damages being the causal effect of performed manipulations, changes, additions made to the product.
• Defects caused by using accessories, components or spare parts other than original HOLZMANN spare parts.
• Slight deviations from the specified quality or slight appearance changes that do not affect functionality or value of the tool.
• Defects resulting from a commercial use of tools that - based on their construction and power output - are not designed and built to be used within the frame of industrial/commercial continuous load.

G) Claims other than the right to correction of faults in the tool named in these guarantee conditions are not covered by our guarantee.

H) This guarantee is voluntary. Therefore Services provided under guarantee do not lengthen or renew the guarantee period for the tool or the replaced part.

SERVICE

After Guarantee and warranty expiration specialist repair shops can perform maintenance and repair jobs. But we are still at your service as well with spare parts and/or product service. Place your spare part / repair service cost inquiry by filing the SERVICE form on the following page and send it:

via Mail to [e-mail]

or via Fax to: [phone]

PRODUCT EXPERIENCE FORM

We observe the quality of our delivered products in the frame of a Quality Management policy.

Your opinion is essential for further product development and product choice. Please let us know about your:

• Impressions and suggestions for improvement.
• experiences that may be useful for other users and for product design
• Experiences with malfunctions that occur in specific operation modes

We would like to ask you to note down your experiences and observations and send them to us via FAX, E-Mail or by post:

Erworbenvon / purchased from:

E-Mail/e-mail:

/ service inquiry / spare part inquiry / guarantee claim

Please describe amongst others in the problem: What has cause the problem/defect, what was the last activity before you noticed the problem/defect? For electrical problems: Have you had checked you electric supply and the machine already by a certified electrician?

3. Bitte beachten

/ Additional information

INCOMPLETELY FILLED SERVICE FORMS CANNOT BE PROCESSED! FOR GUARANTEE CLAIMS PLEASE ADD A COPY OF YOUR ORIGINAL SALES / DELIVERY RECEIPT OTHERWISE IT CANNOT BE ACCEPTED. FOR SPARE PART ORDERS PLEASE ADD TO THIS SERVICE FORM A COPY OF THE RESPECTIVE EXPLODED DRAWING WITH THE REQUIRED SPARE PARTS BEING MARKED CLEARLY AND UNMISTAKABLE. THIS HELPS US TO IDENTIFY THE REQUIRED SPARE PARTS FASTLY AND ACCEL- ERATES THE HANDLING OF YOUR INQUIRY.