WLA-5000AP - Access Point AIRLIVE - Free user manual and instructions

Product Type	Wireless Access Point
Brand	AirLive
Model	WLA-5000AP
Wireless Standards	IEEE 802.11a/b/g
Frequency Bands	2.4 GHz (b/g) and 5 GHz (a)
Operating Modes	AP+WDS, Client, Repeater (via firmware)
Default IP Address (AP+WDS)	192.168.1.1
Default IP Address (Client)	192.168.1.2
Default Subnet Mask	255.255.255.0
Default Password	airlive
Default SSID	airlive
LED Indicators	Power (green solid), LAN (green solid/flashing), Wireless (green solid/flashing)
Ports	1x LAN (RJ45), 1x Power (DC), Reset button
Antenna	External, screw-in (reverse polarity)
Power Supply	DC adapter (included)
Firmware Upgrade	Via web interface; requires reset after upgrade
Security	Default password; WEP/WPA supported (set via web)
Regulatory Compliance	FCC, CE
Country Code Adjustment	Via telnet command
Dimensions	Not specified
Weight	Not specified
Maintenance	Keep clean, avoid moisture

Frequently Asked Questions - WLA-5000AP AIRLIVE

What are the default IP addresses of the WLA-5000AP?

The default IP address for AP+WDS mode is 192.168.1.1, and for Client mode it is 192.168.1.2.

How do I reset the access point to factory defaults?

Press and hold the Reset button on the back panel for at least 10 seconds.

What is the default administrator password?

The default password is airlive.

How can I change the firmware to Client mode?

Log into the web interface, go to System Tools > Firmware Upgrade, select the Client mode firmware from the CD-ROM, and upgrade. After upgrade, reset the device for 10 seconds.

How do I switch between 802.11a and 802.11b/g modes?

Access the web interface, go to Setup Wizard > Wireless Setting, and choose the desired WLAN standard (802.11a or 802.11b/g). Note: Super A/G modes are not supported in WDS or Repeater.

What do the LED indicators mean?

Power: solid green when on. LAN: solid when link is detected, flashing during data transfer. Wireless: solid when wireless connection established, flashing during activity.

Can the access point work in both 2.4GHz and 5GHz simultaneously?

No, it cannot run both 802.11a (5GHz) and 802.11b/g (2.4GHz) at the same time.

How do I change the country code for regulatory compliance?

Use Telnet to connect to the AP, login with password, then issue the command z_debug wlanrd write , then reset system.

What are the supported wireless modes?

The AP supports AP+WDS, Client, and Repeater modes. Client mode requires a separate firmware.

How do I connect to the access point for the first time?

Connect your computer to the LAN port, set your IP to 192.168.1.x (subnet 255.255.255.0), then open a browser to 192.168.1.1. Use the default password airlive.

USER MANUAL WLA-5000AP AIRLIVE

802.11a/b/g Multi-function Wireless Access Point

*◆✿✿✿ *✿▼◆□ ◆✿✿✿

English . . .

1

Slovensky •••

7

Česky

● ● ●

13

Made by OvisLink Corp.

Important Information

☐ The AP+WDS mode's default IP address is 192.168.1.1
The Client mode's default IP is 192.168.1.2
☐ The default Subnet Mask is 255.255.255.0
☐ The default password is airlive
☐ The default SSID is airlive
☐ The default DHCP client is Disabled

☐ The default is set to AP+WDS mode firmware
☐ You need to change the firmware to use the Client Mode. The client mode firmware is in the supplied CD ROM's Firmware directory.
☐ The WDS and Repeater mode does not work in Turbo mode. When using those Mode, please do not select Super A or Super G modes.

LED Indicators

LED		Status
Indicator	Meaning	Solid Flashing
	Power	Turns solid green when power is ON	N/A.
	LAN LAN Connection is detected.		Receiving/ Sending data
	Wireless Connection is made		Receiving/ Sending data

Ports and Connectors

• Reset: Press 10 seconds to restore settings to factory default
• LAN: Connect your PC, Switch, or Router here.
  ● Power: Connect the included Power adapter here.
• Antenna: Install Antenna Here

Installation Steps

1. Please install your network cards first before the AP
2. Screw-in the antenna (clockwise) into the Antenna connector
3. Connect the power and LAN cable to the back
4. Use your wireless card to do a site survey, the default SSID is airlive
5. If you need to change AP's configuration, please follow the procedure below:

■ The AP mode's default IP address is 192.168.1.1. Please make sure your computer IP is in the same subnet as the AP (i.e. 192.168.1.x)
■ Open the web browser and enter 192.168.1.1.
■ Enter the Password airlive.

Changing Firmware

The default firmware is AP+WDS firmware, the AP mode and WDS mode uses the same firmware.

If you need to use the Client mode feature, you have to change the firmware. Please follow the instruction below:

1. Open your web browser, enter your AP's IP address (AP mode default is 192.168.1.1).
2. When you are asked about the password. Please enter airlive in the password field.
3. When the following screen appears. Please click on the System Tools.

1. Please select Firmware Upgrade option from the System Tools menu.
2. Click on the browse button. Please insert the product CD. Choose the CD ROM's Firmware directory. Select the Client mode firmware.
3. Click the upgrade button. Please do not touch the computer or turn off the AP during the upgrade process.
4. After the Upgrade is finished. Please press the Reset button for 10 seconds to restore to factory's default
5. The AP's IP address is now changed to 192.168.1.2.

Select 802.11a, b, or g mode

The AP is default to 802.11g/b mode, running in 2.4Ghz spectrum. If you want to run it in 802.11a mode, you need to change the settings. The AP can not run in both 802.11a and 802.11g mode simultaneously.

1. Open your web browser and enter the AP's IP address.
2. Select Setup Wizard, then Wireless Setting on the left side
3. In the WLAN standard. Please choose the 802.11a. Only choose the Super A mode when you are connecting with another Super A device.
4. Click on Next to finish the setting

Please refer to the complete User's Guide on the CD-ROM for more information.

802.11a Frequency Domain

The legal frequency range for Czech and Slovakia Countries are as followed:

• Indoor: 5.18 to 5.32GHz
  • Outdoor: 5.50 to 5.7GHz

Your AP comes with the above frequency bands open. If you are using 802.11a mode in Czech and Slovakia countries, please do not use "auto" channel selection. Please choose your frequency channel according to the instruction below:

- Indoor: Channel 36, 40, 44, 48, 52, 56, 60, 64

● Outdoor: Channel 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140

Changing Frequency Domain

The AP is default to comply with the frequency domain of your country. Please do not change it unless you are operating the AP in a different domain.

The instruction for changing the domain is as followed:

1. From the DOS Command Windows. Type "Telnet "
2. Enter your password to login.
3. Enter "z_debug wlanrd write " to change country code
4. Enter "reset system" to reboot your device to use the new regulatory domain id.

Current Supported Country Codes:

American Countries:

United States(840)

Asian Countries:

China(156)

Hong

Kong(344)

Japan(392)

Japan3(395)

South

Korea(410)

Thailand(764)

European Countries:

Austria(40)

Belgium(56)

Cyprus(196)

Czech

Republic(203)

Denmark(208)

Estonia(233)

Finland(246)

France(250)

Germany(276)

Hungary(348)

Ireland(372)

Italy(380)

Lithuania(440)

Luxembourg(442)

Netherlands(528)

Poland(616)

Portugal(620)

Slovakia(703)

Slovenia(705)

Spain(724)

Sweden(752)

United

Kingdom(826)

Oceanic Countries:

Australia(36)

MEMO

Dôležité informácie

□ Prednastavená IP adresa pre AP+WDS mód je 192.168.1.1
□ Prednastavená IP adresa pre mód Klient je 192.168.1.2
□ Prednastavená sietová maska je 255.255.255.0
□ Prednastavené heslo je airlive
□ Prednastavené SSID je airlive
□ Prednastavená hodnota pre DHCP klient je Disabled

1. Kliknite na tlačidlo Browse. Do CD mechaniky vložte CD-ROM priložený k produktu, nalistuje adresár Firmware. Zvol'te súbor s firmvérom Client mode.
2. Kliknite na tlačidlo Upgrade. Kým nie je proces zmeny firmvéru ukončený, nezasahujte do počítača ani nevypínajte AP!
3. Po ukončení zmeny firmvéru vykonajte návrat k prednastaveným hodnotám stlačením tlačidla Reset na 10 sekúnd.
4. IP adresa AP sa zmení na 192.168.1.2.

Vol'ba módu 802.11a, b/g

Instalační kroky

OvisLink Corporation declares that this device is in compliance with the essential requirements and other relevant provisions of directive 1999/5/EC

Tested To Comply

With FCC Standards

FOR HOME OR OFFICE USE