ND-183-D - Frying Pan Cotech - Free user manual and instructions

Type	Electric fireplace stove fan heater
Model	ND-183-D
Brand	Cotech
Dimensions (H × W × D)	74 × 44 × 32 cm
Weight	Approx. 12.5 kg
Rated Voltage	220–240 V AC, 50 Hz
Power Settings	1000 W (low) and 2000 W (high)
Heat Output (Nominal)	2.0 kW
Heat Output (Minimum)	1.0 kW
Flame Effect	LED-based, can operate without heat
Thermostat	Adjustable, with automatic on/off
Safety Features	Overheating protection, tip-over switch
Recommended Clearances	120 cm front, 50 cm other sides
Mains Lead Length	1.5 m
Light Source	LED (non-replaceable)
Energy Efficiency Class	Seasonal space heating efficiency 36%
Cleaning	Soft cloth, vacuum air vents
Use	Indoor, temporary heating of well-insulated rooms
Country of Origin	Sweden (CLAS OHLSON AB)

Frequently Asked Questions - ND-183-D Cotech

How do I use only the flame effect without heat?

Set the [I/O] switch to I to turn on the flame effect. Do not press any power setting buttons (I or II). To turn off, set switch to 0.

How do I adjust the thermostat?

Turn the thermostat knob clockwise to increase temperature, anticlockwise to decrease. When the room reaches desired temperature, slowly turn knob back until it clicks; the heater will then cycle automatically.

What should I do if the heater stops working?

Check if the power switch is on (I), the mains lead is plugged in, and the wall socket is live. If the heater overheated, the overheating protection may have tripped: set switch to 0, unplug, wait 15 minutes, then plug back in.

Can I use an extension cord?

No. The manual explicitly states: 'Never connect the product to the electricity mains using an extension lead.' Plug directly into an earthed 230 V outlet.

Is the stove safe to use around children?

The product can become very hot. Children under 3 must be kept out of reach. Children aged 3–8 may only switch it on/off with supervision. Never leave children unattended near the stove.

How do I clean the stove?

First, switch off and unplug the stove and let it cool. Wipe the exterior with a soft cloth (damp if needed, no detergents). Regularly vacuum the air inlet and outlet to prevent dust buildup.

What happens if the stove tips over?

The built-in tip-over switch automatically turns off the stove if it tilts or falls. Once returned to an upright position, the switch resets and the stove can be used normally.

Can I replace the LED bulbs?

No. The LEDs are non-replaceable. They are designed to last the lifetime of the product. Do not attempt to open the housing.

What are the dimensions and weight of the stove?

The dimensions are 44 × 32 × 74 cm (width × depth × height) and it weighs approximately 12.5 kg.

Can I use the stove in a bathroom or near water?

No. The manual warns: 'Never use the product in the immediate vicinity of bathtubs, showers or swimming pools.' It is for indoor dry use only.

USER MANUAL ND-183-D Cotech

Important:

Read the entire instruction manual carefully and make sure that you fully understand it before you use the equipment. Keep the manual for future reference.

Viktig information:

Original instructions

Bruksanvisning i original

Originalbruksanvisning

Please read the entire instruction manual before use and then save it for future reference. We reserve the right for any errors in text or images and any necessary changes made to technical data. In the event of technical problems or other queries, please contact our Customer Services (see address details on the back).

Safety

General requirements for household electrical appliances

• The product may be used by children of 8 years and above and by persons with reduced physical, sensory or mental capability or lack of experience and knowledge provided they have been given supervision or instruction concerning use of the product in a safe way and understand the hazards involved.
• Never let children play with the product.
• Cleaning and user maintenance must not be performed by children without adult supervision.

Particular requirements for room heaters

Warning: Never cover the product. If covered, there is a risk of overheating or even fire.

⚠ Warning

• The product can become very hot during use and cause burns. Burn hazard. Special care must be taken if the product is used in the same room as young children, aged or infirm persons.
• The product must never be placed directly beneath a wall socket.
• Never use the product in the immediate vicinity of bathtubs, showers or swimming pools.

• The appliance must be kept out of reach of children under 3 years of age unless they are under constant supervision.

• Children between the ages of 3 and 8 years must only switch the appliance on/off provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

• Children between the ages of 3 and 8 years must not plug in, regulate and clean the appliance or perform user maintenance.

Safety instructions

⚠ Warning: Dangerous voltage

• The product should not be used if it is in any way damaged or malfunctioning. Do not use the product if the mains lead or plug is damaged in any way.
• The mains lead must be changed if damaged. This is to prevent the risk of electric shock or fire and should only be carried out by the manufacturer, qualified service facility or qualified technician.
• The product must not be taken apart or modified. Certain unshielded components inside the housing carry dangerous voltages. Contact with these can lead to fire or electric shock.
• Never lower the product into water or other liquids.
• Never touch the control panel or plug with wet hands.
• Never use the product in the rain or in wet conditions.

Warning

• Never leave the product unattended while in use.
• Do not touch any hot surfaces on the product; doing so could result in burns. Never move the product while it is in use or before it has cooled down.

• Fire hazard. Flammable materials such as furniture, paper, clothing and curtains must be at kept at a distance of at least 120 cm away from the front of the product above and at least 50 cm in all other directions.

• Do not place towels or similar objects on the product.

• Ensure that the product is kept clean. Make sure that no foreign objects can enter the ventilation openings as this can present a risk of electric shock or fire.
• The product must never be used near flammable gases or liquids.
• The product is only intended for normal domestic use and only in the manner described in this instruction manual. Using the product for other than its intended use may lead to fire, electric shock, other types of personal injuries or material damage.
• Children in the area where the product is used must be kept under supervision.
• The product is intended for indoor use only.
• Make sure to route the mains lead behind the product so that it is not heated by the hot air from the product.
• The product must only be plugged into to an earthed 230 V, 50 Hz power outlet. Never connect the product to the electricity mains using an extension lead.

△ Important

• Always unplug the product from the wall socket when it is not in use.
• Disconnect the product from the power supply by unplugging it from the wall socket. Make sure that the wall socket and plug are easily accessible.
• The product must not be connected to the mains during installation or service.
• The product must only be used in the upright position.

Product description

i Information

The product is designed for temporary use in well-insulated rooms.

• Electric fireplace stove fan heater.
- Two heat settings, 1000 and 2000 W.
- Adjustable thermostat.
• Overheating protection.

A. Flame effect
B. Air outlet
C. Control panel
D. Air inlet

Buttons and functions

E. [I/0] Power switch, on/off
F. [I] Power setting I, 1000 W
G. [II] Power setting II, 2000 W
H. Thermostat knob

Instructions for use

Note

Bear in mind that factors such as the size of the room, the outside temperature and how well the building is insulated, all affect the ability of the heater to warm the room up. If the room is too large the ability of the heater to warm it up to the desired temperature may be insufficient.

1. Place the electric stove on a firm, level floor surface.
2. Plug the product into a wall socket.

Flame effect without fan heater function

1. Set the [I/O] switch (E) to I to switch the stove on, the flame effect comes on.
2. Set the [I/0] switch to 0 to switch the stove off, the flame effect will go out.

Flame effect plus fan heater function

1. Set the [I/O] switch to I to switch the stove on, the flame effect comes on.
2. Turn the thermostat knob (H) clockwise to the maximum setting.
3. Press in [I] (F) to select 1000 W or press in both [I] and [II] (G) to select 2000 W.

4. When the desired ambient temperature has been reached, slowly turn the thermostat knob back until it clicks and the fan heater switches off. Leave the thermostat knob in that position.

5. The stove will maintain the set temperature by automatically switching on and off.

6. The temperature can be adjusted by turning the thermostat knob:

7. clockwise to raise the temperature

8. anticlockwise to lower the temperature.

9. Set the [I/O] switch to 0 to switch the stove off, the flame effect will go out.

Overheating protection

The electric stove is fitted with an overheating safety cut-off protection device which switches the appliance off if it overheats. To reset the overheating protection device:

1. Set the [I/O] switch to 0.
2. Unplug the stove from the wall socket and let it cool for at least 15 minutes.
3. Then plug the heater back into a wall socket. The heater should now work normally.

Tip-over switch

The electric stove is fitted with a tip-over switch which switches the stove off if it tilts or falls over. The tip-over switch resets when the stove is returned to the upright position.

Care and maintenance

• Switch the stove off, unplug it from the wall socket and let it cool before cleaning.

• Clean the exterior of the stove using a soft cloth. Dampen the cloth with a little water if required, do not use detergent, solvent or corrosive chemicals.

• Get into the habit of vacuum cleaning the air inlet and outlet regularly.

• Store the stove indoors when it is not in use.
• The lights inside the electric stove are LEDs and cannot be replaced.

Troubleshooting guide

The flame effect doesn’t come on.	Is the power switch set to ON (I)?Is the mains lead intact and properly plugged into the wall socket?Is the wall socket live?
The fan heater does not start.	Is the power switch set to ON (I)?Is the power setting I switch pressed in?Are the power setting switches I and II pressed in?Has the thermostat turned off the fan heater?Turn the thermostat knob clockwise.Is the mains lead intact and properly plugged into the wall socket?Is the wall socket live?The overheating protection has tripped. Reset as instructed in the Overheating protection section.
The fan heater starts but stops after a short time.	The thermostat is set to a lower temperature than the current room temperature. Check the thermostat setting.

Responsible disposal

This symbol indicates that this product should not be disposed of with general household waste. This applies throughout the entire EU. In order to prevent any harm to the environment or health hazards caused by incorrect waste disposal, the product must be handed in for recycling so that the material can be disposed of in a responsible manner. When recycling the product, take it to your local collection facility or contact the place of purchase. They will ensure that the product is disposed of in an environmentally sound manner.

Specifications

Rated voltage 220–240 V AC, 50 Hz

Power 1000 and 2000 W

Bulb LED (non-replaceable)

Mains lead 1.5 m

Size 44 × 32 × 74 cm

Weight Approx. 12.5 kg

Information requirement for the electric local space heaters

Model identifier(s): ND-183-D
Art.no: 36-7800
Item Symbol Value Unit	Item
Heat output Type of heat input, for electric storage				local space heaters only (select one)
Nominal heat output P	nom	2.0 kW		manual heat charge control, with integrated thermostat	N/A
Minimum heat output (indicative)	Pmin	1.0 kW		manual heat charge control with room and/or outdoor temperature feedback	N/A
Maximum continuous heat output	Pmax,c	2.0 kW		electronic heat charge control with room and/or outdoor temperature feedback	N/A
Auxiliary electricity consumption	--- --- --- fan assisted heat output N/A
At nominal heat output	eImax	0.013 kW		Type of heat output/room temperature control (select one)
At minimum heat output	eImin	0.013 kW		single stage heat output and no room temperature control	No
In standby mode eI	SB	0	kW	Two or more manual stages, no room temperature control	No
				with mechanic thermostat room temperature control	Yes
				with electronic room temperature control	No
				electronic room temperature control plus day timer	No
				electronic room temperature control plus week timer	No
				Other control options (multiple selections possible)
				room temperature control, with presence detection	No
				room temperature control, with open window detection	No
				with distance control option No
				with adaptive start control	No
				with working time limitation	No
				with black bulb sensor	No
Contact details	CLAS OHLSON AB, SE-793 85 INSJÖN, SWEDEN

Test Data

Commission Regulation (EC) No 1275/2008 Requirement

Mode Ecodesign	requirements, from 7 January 2013 Result - Remark Verdict
Off mode Power	consumption in ‘off mode’:Power consumption of equipment in any off-mode condition shall not exceed 0.50 W		P
Standby mode P	power consumption in ‘standby mode(s)’:The power consumption of equipment in any condition providing only a reactivation function, or providing only a reactivation function and a mere indication of enabled reactivation function, shall not exceed 0.50 W.		N/A
	The power consumption of equipment in any condition providing only information or status display, or providing only a combination of reactivation function and information or status display shall not exceed 1.00 W.		N/A

Seasonal space heating energy efficiency

Description Value
Seasonal space heating energy efficiency in active mode- ηS,on	40 %
For electric local space heaters- ηth
The electric to primary energy “conversion coefficient”-CC
F(1) is a correction factor accounting for a positive contribution to the seasonal space heating energy efficiency of electric storage local space heaters due to adjusted contributions for options for heat storage and output; and a negative contribution to seasonal space heating efficiency for commercial local space heaters due to adjusted contributions for options for the heat output, expressed in %;	0 %
F(2) is a correction factor accounting for a positive contribution to the seasonal space heating energy efficiency due to adjusted contributions of controls of indoor heating comfort, the values of which are mutually exclusive, cannot be added to each other, expressed in %;	6 %
F(3) is a correction factor accounting for a positive contribution to the seasonal space heating energy efficiency due to adjusted contributions of controls for indoor heating comfort the values of which can be added to each other, expressed in %;	0 %
F(4) is a correction factor accounting for a negative contribution to the seasonal space heating energy efficiency by auxiliary electricity consumption, expressed in %;	0 %
F(5) is a correction factor accounting for a negative contribution to the seasonal space heating energy efficiency by energy consumption of a permanent pilot flame, expressed in %.	0 %
Seasonal space heating energy efficiency- ηS	36 %
Verdict	P

Dekorationskamin

Art.nr 36-7800 Modell ND-183-D

Användning

Obs!

Specifikationer

Nätanslutning 220–240 V AC, 50 Hz

Bruk

Obs!

Spesifikasjoner

Strømtilkobling 220–240 V AC, 50 Hz

Käyttö

△ Huom!

Tekniset tiedot

Bedienung

△ Hinweis

Technische Daten

POSTAL 10 - 13 Market Place

Kingston Upon Thames

Surrey

KT1 1JZ

DEUTSCHLAND

KUNDENSERVICE Hotline: [phone]

E-Mail: [e-mail]

HOMEPAGE

www.clasohlson.de

POSTANSCHRIFT