KW-AVX710 - Car stereo JVC - Free user manual and instructions

USER MANUAL KW-AVX710 JVC

07.12.7 2:33:37 PM ENGLISH Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit.

IMPORTANT FOR LASER PRODUCTS 1. 2. 3. 4.

CLASS 1 LASER PRODUCT CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.

WARNINGS: To prevent accidents and damage

This symbol is only valid in the European Union.

• DO NOT install any unit or wire any cable in a location where; – it may obstruct the steering wheel and gearshift lever operations. – it may obstruct the operation of safety devices such as air bags. – it may obstruct visibility. • DO NOT operate the unit while driving. If you need to operate the unit while driving, be sure to look around carefully. • The driver must not watch the monitor while driving.

Information for Users on Disposal of Old Equipment This symbol indicates that the product with this symbol should not be disposed as general household waste at its end-of-life. If you wish to dispose of this product, please do so in accordance with applicable national legislation or other rules in your country and municipality. By disposing of this product correctly, you will help to conserve natural resources and will help prevent potential negative effects on the environment and human health.

Cautions on the monitor: • The monitor built in this unit has been produced with high precision, but it may have some ineffective dots. This is inevitable and is not malfunction. • Do not expose the monitor to direct sunlight. • Do not operate the touch panel using a ball-point pen or similar tool with the sharp tip. Touch the buttons on the touch panel with your finger directly (if you are wearing a glove, take it off).

• When the temperature is very cold or very hot... – Chemical changes occur inside, causing malfunction. – Pictures may not appear clearly or may move slowly. Pictures may not be synchronized with the sound or picture quality may decline in such environments.

EN_KW-AVX710[E]4.indb 2

07.12.7 10:44:01 AM How to reset your unit

INTRODUCTION Playable disc types 4 Basic operations— Monitor panel/touch panel 5 Basic operations— Remote controller (RM-RK252) 6

• Your preset adjustments will also be erased.

How to forcibly eject a disc

ENTER NO EJECT? EMERGENCY EJECT?

OPERATIONS Before operating the unit 8 Common operations 9 Listening to the radio 10 Disc operations 16

EXTERNAL DEVICES Bluetooth® operations— Cellular phone/audio player 30 Listening to the CD changer 37 Listening to the DAB tuner 39 Listening to the iPod 43 Using other external components 45

• If this does not work, reset the unit. For safety... • Do not raise the volume level too much, as this will block outside sounds, making driving dangerous. • Stop the car before performing any complicated operations. Temperature inside the car... If you have parked the car for a long time in hot or cold weather, wait until the temperature in the car becomes normal before operating the unit.

SETTINGS Sound equalization 48 Assigning titles to the sources 49 Menu operations 50

For security reasons, a numbered ID card is provided with this unit, and the same ID number is imprinted on the unit’s chassis. Keep the card in a safe place, as it will help the authorities to identify your unit if stolen.

REFERENCES Maintenance 60 More about this unit 61 Troubleshooting 68 Specifications 72

07.12.7 10:44:05 AM ENGLISH Playable disc types Disc type

Recording format, file type, etc.

DVD DVD Video (Region Code: 2)*1

ENGLISH Basic operations — Monitor panel/touch panel

• Display <Open/Tilt> menu. • Eject the disc and display <Open/Tilt> menu. [Hold] • Close the monitor panel when <Open/Tilt> menu is displayed.

• Turn on the power. • Turn off the power. [Hold] • Attenuate the sound (if the power is on).

Reset the unit. • Use only when the internal system malfunctions. • • • • • •

• In the explanation, buttons on the touch panel are indicated inside [ ]. • For details on the touch panel operations, see each source operation section. 5

EN_KW-AVX710[E]4.indb 5

[OPEN]: Open the monitor panel. [EJECT]: Eject the disc. [CLOSE]: Close the monitor panel. [TILT +/–]: Tilt the monitor panel. [Exit]: Erase this screen. Shaded icons cannot be used.

07.12.7 10:44:07 AM ENGLISH Basic operations — Remote controller (RM-RK252) Installing the battery

Main elements and features

R03/LR03/AAA Insert the batteries into the remote controller by matching the polarity (+ and –) correctly.

Caution: Battery shall not be exposed to excessive heat such as sunshine, fire or the like. • If the range or effectiveness of the remote controller decreases, replace both batteries. Before using the remote controller: • Aim the remote controller directly at the remote sensor on the unit. • DO NOT expose the remote sensor to bright light (direct sunlight or artificial lighting). The unit is equipped with the steering wheel remote control function. • See the Installation/Connection Manual (separate volume) for connection.

• Turns on the power. • Attenuates the sound if the power is on. • Turns off the power if pressed and held (while the power is on).

• Reverse search • Reverse slow motion (during pause)

Adjusts the volume level. • Does not function as “2nd VOL.”

Shows the on-screen bar. • Does not function as “ .“

EN_KW-AVX710[E]4.indb 6

07.12.7 10:44:07 AM Functions with other buttons (see i and o).

Changes the display information.

For disc operations: • 5 / ∞: DVD: Selects the title. DVD-VR: Selects the program/Playlist. Other discs (except VCD/CD): Selects the folders. • 4 / ¢: – Press briefly: reverse skip/forward skip – Press and hold: reverse search/forward search For FM/AM operations: • 5 / ∞: Selects the preset stations. • 4 / ¢: Functions to search for stations. – Press briefly: Auto Search – Press and hold: Manual Search For DAB tuner operations: • 5 / ∞: Select the services. • 4 / ¢: Functions to search for ensembles. – Press briefly: Auto Search – Press and hold: Manual Search For Apple iPod operations: • ∞: Starts playback/pauses • 5: Enters the main menu (then 5 / ∞ / 4 / ¢ work as menu selecting buttons). In the main menu: • 5: Returns to the previous menu. • ∞: Confirms the selection. • 4/¢ – Press briefly: Selects an item. – Press and hold: Skips ten items at a time. For Bluetooth operations: • 4 / ¢: reverse skip/forward skip (for audio player operation)

For disc operations: Starts playback/pauses. For Bluetooth operations: • Answers incoming calls. • Starts playback/pauses. (for audio player operation).

Changes the aspect ratio of the playback pictures.

“TUNER”/”DAB”: Selects the bands. “DISC”: Stops playback. “Bluetooth PHONE”: Ends the call. “Bluetooth AUDIO”: Starts playback/pauses.

• Makes selection/settings. • @ / #: Skips back or forward by five minutes for DivX/MPEG1/MPEG2. • % / fi: Changes discs for “CD-CH.”

i*3 • Switches number entry mode for “DISC.” • Erases the misentry after entering a wrong number. • Does not function as “SURROUND.” o*3 Number buttons • Enters numbers. • “TUNER”/”DAB”: Selects the preset station/ service directly. *1 Functions as a number button only (see o ). *2 Not used for this unit. *3 Functions when pressed with SHIFT.

07.12.7 10:44:08 AM ENGLISH Before operating the unit @

You can cancel the demonstration on the screen and set the clock. • Non-available items will be shaded on the AV Menu screens.

Set the clock settings. Moves to the preceding menu page

Indication language: In this manual, English indications are used for purpose of explanation. You can select the indication language. (☞ page 52) Moves to the succeeding menu page

Finish the procedure.

Cancel the demonstration. Select <Off>.

Return to the previous screen.

EN_KW-AVX710[E]4.indb 8

07.12.7 10:44:09 AM Selecting the playback source

ENGLISH Common operations Changing the display information

• Available sources depend on the external components you have connected, media you have attached, and the <Input> settings you have made (☞ page 55).

• Available display information varies among the playback sources.

On the monitor panel only:

• Each time you press DISP, the display changes to show the various information. Ex. When the playback source is a DivX disc. Playback picture screen (only for video sources)

Source information screen Exit

On the monitor panel: Track list

Clock time in large numbers

TUNER = DAB = DISC (DVD/VCD/CD) =CD-CH, iPod, or EXT-IN = Bluetooth PHONE = Bluetooth AUDIO = AV-IN = (back to the beginning)

Navigation screen (When <Navigation> is selected for <AV Input>) (☞ page 55)

• You cannot select these sources if they are not ready. Back to the beginning

PS (station name) for FM RDS. If no PS signal is coming in, the tuned frequency appears.

• You can also use SOURCE on the monitor panel. Press it repeatedly.

: Buttons on the touch panel. In the explanation, they are indicated inside [ ].

Press [4] or [¢] to search for a station—Auto Search. • Manual Search: Hold either [4]or [¢] until “Manual Search” appears on the screen, then press it repeatedly. • The ST indicator lights up when receiving an FM stereo broadcast with sufficient signal strength.

When an FM stereo broadcast is hard to receive 1

Reception improves, but stereo effect will be lost. • The MONO indicator lights up. To restore stereo effect, select <Off>.

EN_KW-AVX710[E]4.indb 10

07.12.7 10:44:10 AM Manual presetting Ex.: Storing FM station of 92.5 MHz into preset number 4 of the FM1 band.

This function works only for FM bands. Once you have activated this function (selected <Local>), it always works when searching for FM stations.

Tune in to a station you want to preset.

Select a preset number.

ENGLISH Tuning in to stations with sufficient signal strength

Press [AV MENU]. Press [Mode].

Only stations with sufficient signal strength will be detected. • The DX indicator goes off, then the LO indicator lights up.

FM station automatic presetting —SSM (Strong-station Sequential Memory) This function works only for FM bands. You can preset six stations for each band.

Press [AV MENU]. Press [Mode].

The station selected in step 2 is now stored in preset number 4. Local FM stations with the strongest signals are searched and stored automatically in the FM band.

EN_KW-AVX710[E]4.indb 11

07.12.7 10:44:10 AM ENGLISH Selecting a preset station

The following features are available only for FM RDS stations.

Searching for FM RDS programme—PTY Search

You can search for your favorite programmes being broadcast by selecting the PTY code for your favorite programmes.

• To select from the Preset List You can also easily access <PTy Search> menu by pressing [SHORT CUT] on the touch panel, then...

EN_KW-AVX710[E]4.indb 12

07.12.7 10:44:11 AM Storing your favorite programme types

Select a PTY code. • In the example below, a PTY code is selected from the Preset List. If you enter <PTy Code> menu below, you can select one from 29 PTY codes.

You can store your favorite PTY codes into the PTY Preset List. Ex.: Storing <Drama> into <Preset 1>

PTY Search starts. If there is a station broadcasting a programme of the same PTY code as you have selected, that station is tuned in.

Available PTY codes: News, Current Affairs, Information, Sport, Education, Drama, Cultures, Science, Varied Speech, Pop Music, Rock Music, Easy Listening, Light Classics M, Serious Classics, Other Music, Weather & Metr, Finance, Children’s Progs, Social Affairs, Religion, Phone In, Travel & Touring, Leisure & Hobby, Jazz Music, Country Music, National Music, Oldies Music, Folk Music, Documentary

on the monitor panel to

The unit will temporarily switch to Lights up Traffic Announcement (TA) if available, from any source other than AM. • The volume changes to the preset TA volume level if the current level is lower than the preset level (☞ page 54). Not yet activated. Tune in to another station providing the RDS signals.

Press [AV MENU]. Press [Mode].

PTY Standby Reception is now activated for PTY code <News>: the initial setting.

You can easily activate or deactivate the PTY Standby Reception by pressing [SHORT CUT] on the touch panel, then...

PTY The unit will temporarily switch to Lights up your favorite PTY programme from any source other than AM. Not yet activated. Tune in to another station providing the RDS signals.

To deactivate, press [Off] for <PTy Standby> in step 3 on the next column.

• When a DAB tuner is connected, TA Standby/PTY Standby Reception also works for the DAB tuner and searches for the services.

When driving in an area where FM reception is not sufficient enough, this unit automatically tunes in to another FM RDS station of the same network, possibly broadcasting the same programme with stronger signals.

Press [AV MENU]. Press [Mode].

ENGLISH To change the PTY code for PTY Standby Reception

Programme A broadcasting on different frequency areas (01 – 05) A

Select your favorite PTY code. Ex.: Selecting <Easy Listening>

When shipped from the factory, Network-Tracking Reception is activated. To change the Network-Tracking Reception setting, see <AF Regional>. (☞ page 54) • When the DAB tuner is connected, refer also to “Tracing the same programme—Alternative Frequency Reception (DAB AF).” (☞ page 42)

Automatic station selection— Programme Search Usually when you select preset stations, the preset station is tuned in. If the signals from the FM RDS preset station are not sufficient for good reception, this unit, using the AF data, tunes in to another station broadcasting the same programme as the original preset station is broadcasting. To activate this function, select <On> for <Program Search>.(☞ page 54) • The unit takes some time to tune in to another station using programme search.

EN_KW-AVX710[E]4.indb 15

07.12.7 10:44:13 AM ENGLISH Disc operations The disc type is automatically detected, and playback starts automatically (for some discs: automatic start depends on its internal program). If a disc does not have any disc menu, all tracks on it will be played repeatedly until you change the source or eject the disc. If “ ” appears on the screen, the unit cannot accept the operation you have tried to do. • In some cases, without showing “ ,” operations will not be accepted.

Open the monitor panel.

<Open/Tilt> menu is displayed. • By pressing and holding the button, you can open the monitor panel and eject the disc.

Monitor panel closes automatically. If not, press [CLOSE].

Caution: Do not place your finger behind the monitor panel.

When playing back a multi-channel encoded disc, the multi-channel signals are downmixed. • You can fully enjoy multi-channel sound by connecting an amplifier or a decoder compatible with these multi-channel sources. (☞ also page 65)

Caution on volume setting: Discs produce very little noise compared with other sources. Lower the volume before playing a disc to avoid damaging the speakers by the sudden increase of the output level. 16

EN_KW-AVX710[E]4.indb 16

07.12.7 10:44:13 AM ENGLISH While playing the following discs, press . • Each time you press the button, the display changes to show the different information. (☞ page 9)

DVD Video: Title no./Chapter no./Playing time DVD-VR: Program no. (or Playlist no.)/Chapter no./Playing time

Sampling frequency/Bit rate/Recorded signal channel no.

Disc type *1 Audio format Sound mode (☞ page 48) Playback mode

☞ page 22 [3 / 8] Start and pause playback [7] Stop playback [4 ¢] Press: Select chapter Hold: Reverse/forward search*2 [5 ∞] Select title/program/playlist

*1 DVD-VR also indicates either PRG (program) or PLAY (playlist) playback. *2 Search speed: x2 ] x10

: Buttons on the touch panel. In the explanation, they are indicated inside [ ]. These buttons also work when they are not shown on the touch panel (while watching the playback pictures on the screen).

EN_KW-AVX710[E]4.indb 17

07.12.7 10:44:14 AM ENGLISH While playing the following discs, press . • Each time you press the button, the display changes to show the different information (☞ page 9).

For DivX/MPEG1/MPEG2: Folder no./Track no./Playing time For JPEG: Folder no./File no.

Disc type Sound mode (☞ page 48)

Total track no. included on the disc

☞ page 22 [3 / 8] Start and pause playback [ 7] Stop playback [4 ¢] Press: Select track Hold: Reverse/forward search for DivX/MPEG1/MPEG2 *1 [5 ∞] Press: Select folder Hold: Display Folder list

Track no./Playing time

The PBC indicator lights up when PBC is in use.

Total track no. included on the disc

Sound mode (☞ page 48)

☞ page 22 [3 / 8] Start and pause playback [ 7] Stop playback [4 ¢] Press: Select track Hold: Reverse/forward search*2

*1 Search speed: ¡1 ] ¡2 *2 Search speed: x2 ] x10 18

EN_KW-AVX710[E]4.indb 18

07.12.7 10:44:14 AM ENGLISH Track no./Playing time

Only for CD Text *3 Total track no. included on the disc

Sound mode (☞ page 48)

Total playing time ☞ page 22 [3 / 8] Start and pause playback [7] Stop playback [4 ¢] Press: Select track Hold: Reverse/forward search*4

Folder no./Track no./Playing time

Audio format (MP3/WMA/WAV) Tag data appears only when it is recorded.

Sound mode (☞ page 48) Total track no. included on the disc

[3 / 8] Start and pause playback [ 7] Stop playback [4 ¢] Press: Select track Hold: Reverse/forward search*4 [5 ∞] Press: Select folder Hold: Display Folder list

*3 “No Name” appears for conventional CDs. *4 Search speed: x2 ] x10 19

EN_KW-AVX710[E]4.indb 19

07.12.7 10:44:15 AM ENGLISH Operation buttons on the screen You can display the following operation buttons while watching the playback pictures on the screen. • While the operation buttons are displayed, aspect ratio is fixed to <Full>. (☞ page 52) • If no operation is done for about five seconds, the operation buttons disappear (except when a disc menu is displayed).

☞ pages 23 to 27 on how the operation buttons particularly work for a variety of the discs

A [SOURCE] [AV MENU] [SHORT CUT] [3 / 8] [7] [4 ¢]

Display <Source Menu> screen Display <AV Menu> screen Display the Short Cut buttons Start and pause playback Stop playback Press: Select track Hold: Reverse/forward search [5 ∞] Select folders • The above buttons also work when they are not shown on the screen (while watching the playback picture). * While a disc menu is played back for DVD, [KEY] is automatically displayed. On the disc menu, you can select a menu item directly by touching it on the screen.

Touch the screen (center portion).

B For DVD/VCD/DivX menu operation playback [2 3 5 ∞] Select the menu items [ENT] Confirm the selection [TOP MENU] Display the disc menu [MENU] Display the disc menu [RETURN] Return to the previous menu or display the menu (only for VCD with PBC)

C For entering the numbers [DIRECT CLR] • Switch between chapter/track entry and title/group/folder entry • Erase the last entry when you enter a wrong number [0]–[9]=[ENT] Enter numbers Ex.: To enter “105,” press [1], [0], [5], then [ENT]

To erase the operations, touch the screen again. 20

EN_KW-AVX710[E]4.indb 20

07.12.7 10:44:15 AM Selecting playback modes 1

ENGLISH You can use the following playback modes—Repeat or Random. Ex.: To select Track Repeat

2 When one of the playback modes is selected, the corresponding indicator lights up on the source information screen. To cancel, select <Off>. Disc type

Chapter: Repeats current chapter Title: Repeats current title Chapter: Repeats current chapter Program: Repeats current program (not available for Playlist playback) Track: Repeats current track Folder: Repeats current folder

Folder: Repeats current folder

— — Folder: Randomly plays all tracks of current folder, then tracks of next folders Disc (All): Randomly plays all tracks —

Repeats current track (PBC not in use)

Disc (All): Randomly plays all tracks (PBC not in use)

Repeats current track*1

Disc (All): Randomly plays all tracks

Track: Repeats current track*1 Folder: Repeats all tracks of the current folder

Folder: Randomly plays all tracks of current folder, then tracks of next folders Disc (All): Randomly plays all tracks

*1 You can also use [SHORT CUT] to turn on and off Track Repeat.

EN_KW-AVX710[E]4.indb 21

07.12.7 10:44:16 AM ENGLISH Selecting tracks on the list

Prohibiting disc ejection

If a disc includes folders, you can display the Folder/ Track (File) Lists, then start playback.

You can lock a disc in the loading slot.

To cancel the prohibition, repeat the same procedure to select <EJECT OK?>.

Select a folder (1), then a track (2).

Using Short Cut Icons You can easily access the some frequently used functions by using [SHORT CUT] on the touch panel.

1 Selected track starts playing. (* Press to move to the previous/next pages of the list) 1 Current folder list number/total folder list number 2 Current track list number/total track list number of the current folder

2 • For video software: Aspect ratio (☞ page 52)

You can easily access the Track List by pressing DISP on the monitor panel.

Sound mode (☞ page 48)

• For audio software:

Turn on or off Track Repeat (Repeat play: ☞ page 21)

Selected track starts playing. 22

EN_KW-AVX710[E]4.indb 22

07.12.7 10:44:17 AM Stop playback. Start playback/pause (if pressed during playback). Reverse/forward search*1 (No sound can be heard.) Slow motion during pause*2 (No sound can be heard.) Press: Select chapter (during playback or pause). Hold: Reverse/forward search*3 (No sound can be heard.)

ENGLISH Operations using the remote controller—RM-RK252

Select title (during playback or pause). Select aspect ratio.

Select chapter. Select title (when not playing).

Select title (during playback or pause). Also functions as CLR (clear): Erases a misentry if pressed while holding SHIFT.

Using menu driven features 1 2 Select an item you want to start playback. 3 *1 Search speed: x2 ] x5 ] x10 ] x20 ] x60 *2 Slow motion speed: 1/32 ] 1/16 ] 1/8 ] 1/4 ] 1/2 *3 Search speed: x2 ] x10

You can change the following items using the on-screen bar—audio language, audio stream, audio channel, subtitle language, view angle, etc. (☞ pages 28 and 29)

EN_KW-AVX710[E]4.indb 23

07.12.7 10:44:17 AM ENGLISH Stop playback. Start playback/pause (if pressed during playback). Reverse/forward search*1 (No sound can be heard.) Forward slow motion during pause*2 (No sound can be heard.) • Reverse slow motion does not work. Press: Select chapter (during playback or pause). Hold: Reverse/forward search*3 Select program. Select playlist (during playback or pause). Select aspect ratio.

Select chapter. Select program (when not playing).

twice Also functions as CLR (clear): Erases a misentry if pressed while holding SHIFT.

Select program/playlist (during playback or pause). Using Original Program/Playlist screens ( ☞ page 28) 1

For Original Program For Playlist

2 Select an item you want to start playback. 3

To erase the screen.

EN_KW-AVX710[E]4.indb 24

07.12.7 10:44:18 AM ENGLISH Stop playback. Start playback/pause (if pressed during playback). Reverse/forward search*4 (No sound can be heard.) Press: Select track Hold: Reverse/forward search*5 (No sound can be heard.) Select folder. Select aspect ratio. Select track (within the same folder). Select folder. twice

While playing... Reverse/advance the scenes by five minutes. Current playback position

07.12.7 10:44:19 AM ENGLISH Stop playback. Start playback/pause. (Slide show: each file is shown for a few seconds.) Shows the current file until you change it if pressed during Slide show. Select file. Select folder. Select aspect ratio.

Select file (within the same folder).

Also functions as CLR (clear): Erases a misentry if pressed while holding SHIFT.

Stop playback. Start playback/pause (if pressed during playback). Reverse/forward search*1 Forward slow motion during pause*2 (No sound can be heard.) • Reverse slow motion does not work. Press: Select track. Hold: Reverse/forward search*3 (No sound can be heard.)

During PBC playback...

Select aspect ratio.

2 Select the desired track.

• To resume PBC, press Select track. *1 Search speed: x2 ] x5 ] x10 ] x20 ] x60 *2 Slow motion speed: 1/32 ] 1/16 ] 1/8 ] 1/4 ] 1/2 *3 Search speed: x2 ] x10 26

EN_KW-AVX710[E]4.indb 26

07.12.7 10:44:19 AM ENGLISH Stop playback. Start playback/pause (if pressed during playback). Reverse/forward search*4 Press: Select track. Hold: Reverse/forward search*5 Select track.

Stop playback. Start playback/pause (if pressed during playback). Reverse/forward search*4 Press: Select track. Hold: Reverse/forward search*5 Select folder. Select track (within the same folder). Select folder. twice

*4 Search speed: x2 ] x5 ] x10 ] x20 ] x60 *5 Search speed: x2 ] x10

07.12.7 10:44:20 AM ENGLISH Using the list screens

Operations using the on-screen bar

You can use Original Program or Playlist screen anytime while playing DVD-VR with its data recorded.

These operations are possible on the screen using the remote controller, while playing the following discs—DVD/VCD/DivX/MPEG1/MPEG2/JPEG.

Display the Original Program/Playlist screen.

Make a selection. If a pop-up menu appears...

Select an item you want.

1 Original Program/Playlist number 2 Recording date 3 Recording source (TV station, the input terminal of the recording equipment, etc.) 4 Start time of recording 5 Title of the program/playlist* 6 Highlight bar (current selection) 7 Creating date of playlist 8 Total number of chapters included in the playlist 9 Playback time

• For entering time/numbers... : Move the entry position

* The title of the original program or playlist may not be displayed depending on the recording equipment.

07.12.7 10:44:21 AM ENGLISH On-screen bar Information Operation

Above example is of DVD Video. Items shown on the bar vary due to the disc type. 1 Disc type 2 • DVD: Audio signal format • VCD: PBC 3 Playback mode *1 DVD Video: C. RPT: Chapter repeat T. RPT: Title repeat DVD-VR: C. RPT: Chapter repeat PG. RPT: Program repeat DivX/MPEG1/MPEG2: T. RPT: Track repeat F. RPT: Folder repeat F. RND: Folder random A. RND: All (Disc) random JPEG: F. RPT: Folder repeat VCD: T. RPT: Track repeat A. RND: All (Disc) random 4 Playback information Current title/chapter

5 Time indication Elapsed playing time of the disc Remaining title time (for DVD) Remaining disc time (for others) Elapsed playing time of the current chapter/track *2 Remaining time of the current chapter/track *2 6 Playback status Play Reverse/forward search Reverse/forward slow-motion Pause Stop 7 Operation icons Change time indication (see 5) Time Search (Specify a certain scene by entering time.) Title Search (by its number) Chapter Search (by its number) Track Search (by its number) Repeat play *1 Random play *1 Change the audio language, audio stream, or audio channel Change or erase the subtitle language Change the view angle

Current program/chapter Current Playlist/chapter Current track Current folder/track Current folder/file

*1 ☞ page 21 *2 Not applicable for DVD-VR

07.12.7 10:44:22 AM ENGLISH Bluetooth® operations — Cellular phone/audio player For Bluetooth operations, it is required to connect the Bluetooth Adapter (KS-BTA200) to the CD changer jack on the rear. • Refer also to the instructions supplied with the Bluetooth Adapter and the Bluetooth device. • Refer to the list (included in the box) to see the countries where you may use the Bluetooth® function.

To register using <Open> Preparation: Operate the Bluetooth device to turn on its Bluetooth function.

To use a Bluetooth device through the unit (“Bluetooth PHONE” and “Bluetooth AUDIO”) for the first time, you need to establish Bluetooth wireless connection between the unit and the device. • Once the connection is established, it is registered in the unit even if you reset your unit. Up to five devices can be registered in total. • Only one device can be connected at a time for each source (“Bluetooth PHONE” and “Bluetooth AUDIO”).

• Make sure “New Device” is selected. If not, press [5] or [∞] to select it.

Connecting a new Bluetooth device Registration (Pairing) methods Use either of the following items in <Bluetooth> menu to register and establish the connection with a device. • Select “Bluetooth PHONE” or “Bluetooth AUDIO” as the source to operate <Bluetooth> menu. Open

Make the unit ready to establish a new Bluetooth connection. The connection is established by operating the Bluetooth device.

Make the unit ready to establish a new Bluetooth connection. The connection is established by operating this unit.

Go to other menu items

Enter a PIN (Personal Identification Number)* code to the unit. • You can enter any number you like (1-digit to 16-digit number). * Some devices have their own PIN code. Enter the specified PIN code to the unit.

EN_KW-AVX710[E]4.indb 30

07.12.7 10:44:23 AM You can enter [0] – [9] only. • [BS]: Erases the character before the cursor. • [Del]: Erases the character on the cursor. • [Enter]: Confirms the entry. Operate the Bluetooth device to connect while “Open...” is displayed on the screen. Enter the same PIN code (as entered in the above step) on the device to be connected.

Now connection is established and you can use the device through the unit.

To register using <Search> • Make sure “New Device” is selected. If not, press [5] or [∞] to select it.

Select a device you want to connect.

Press [Bluetooth]. Press [Special Device]. The unit displays the list of the preset devices. Use <Open> (or <Search>) to connect.

To connect/disconnect a registered device

The device remains registered even after you disconnect the device. Use <Connect> (or activate <Auto Connect>) to connect the same device from next time (☞ the following, and pages 58 and 59).

To connect a special device <Special Device>

Select “Bluetooth PHONE” or “Bluetooth AUDIO,” then select a registered device you want to connect/disconnect.

Press [AV MENU]. Press [Bluetooth]. Press [Search]. The unit searches for available devices and displays the list of them. (If no available device is detected, “Device Unfound” appears.)

Press [Bluetooth]. Press [Connect] or [Disconnect]. • Select <Connect> to connect the selected device. • Select <Disconnect> to disconnect the selected device.

To delete a registered device

Select a device you want to connect. Enter the specific PIN code of the device to the unit. • Refer to the instructions supplied with the device to check the PIN code. Operate the Bluetooth device to connect while “Connecting...” is displayed on the screen.

Select “Bluetooth PHONE” or “Bluetooth AUDIO,” then select a registered device you want to delete.

Press [AV MENU]. Press [Bluetooth]. Press [Delete Pairing]. Confirmation screen appears. Press [Yes].

Now connection is established and you can use the device through the unit.

Status of the device Signal strength/Battery remainder (only when the information comes from the device)

The Bluetooth icon lights up when the adapter is connected. ☞ page 34

Adjust the volume of the incoming calls.*2

: Buttons on the touch panel. In the explanation, they are indicated inside [ ].

[AV MENU] Hold: Activates <Voice Dialing> function [5 ∞] Select the registered device (“New Device” appears when a new device can be registered.)

*1 When a cellular phone with audio function is connected, appears. *2 This adjustment does not affect the volume level of the other sources.

Press [SOURCE], then press [Bluetooth PHONE]. (☞ page 9) • You can also use SOURCE on the monitor panel. Press it repeatedly.

Press [AV MENU]. Press [Bluetooth]. Establish the connection with a device, then make a call (or settings using <Bluetooth> menu). ☞ pages 58 and 59

When a call comes in... The source is changed to “Bluetooth PHONE” automatically.

When <Auto Answer> is deactivated... To answer the incoming call • Press any button on the monitor panel (except /ATT or +/–). • Press the message displayed on the touch panel.

Name and phone number (if acquired)

When an SMS comes in...

ENGLISH If the cellular phone is compatible with SMS (Short Message Service), you can read the messages on the screen. • You cannot edit or send a message through the unit. When <Message Info> is set to <Auto>... The unit rings and the following screen is displayed to inform you of a message arrival. (☞ page 59)

Select a calling method, then call.

Shows the list of the phone numbers you have dialed. Received Calls Shows the list of the received calls. Phonebook Shows the phone book of the connected cellular phone. Missed Calls Shows the list of the missed calls. Phone Shows the phone number Number entry screen = “Entering a phone number” (☞ page 34). Voice Dialing (Only when the connected cellular phone has the voice recognition system): = Speak the name you want to call.

07.12.7 10:44:25 AM ENGLISH To stop ringing (canceling the outgoing call)

To redial previously dialed numbers

Hold any button on the monitor panel (except or +/–).

/ATT Entering a phone number • You cannot use the remote controller to enter phone numbers.

You can enter [0] – [9], [*], [#] (up to 32 numbers) • [BS]: Erases the character before the cursor. • [Del]: Erases the character on the cursor. • [Preset]: Goes to Preset List. You can preset the entered number by selecting a preset number. (☞ page 35) • [Dial]: Calls the entered number.

• You can easily access <Dial Menu> by pressing [SHORT CUT] on the touch panel, then... When using the remote controller, you can display <Redial> menu anytime . You can also access <Dial Menu> by holding SOURCE on the monitor panel. [Hold] • You can easily activate <Voice Dialing> by pressing [SHORT CUT] on the touch panel, then...

You can also activate <Voice Dialing> by holding [AV MENU].

EN_KW-AVX710[E]4.indb 34

You can preset up to six phone numbers.

ENGLISH Presetting the phone numbers Select the phone number you want to preset from <Phonebook>, <Redial>, <Received Calls>, or <Missed Calls>. 1 Press [AV MENU]. 2 Press [Bluetooth]. 3 Press [Dial Menu], then...

2 Ex.: Selecting <Received Calls>

Select a telephone number to store.

You can use the following buttons on the remote controller for the Bluetooth phone operations.

Select a preset number.

: • Display <Dial Menu> screen/Answer the incoming call. • Display the <Redial> menu if pressed and held (regardless of the current source). : End the call.

Now “Tom” is stored into preset no. 1.

: Adjust the volume.

: [Hold] Make a call to the preset numbers.

EN_KW-AVX710[E]4.indb 35

07.12.7 10:44:27 AM Using the Bluetooth audio player ENGLISH

*2 Sound mode (☞ page 48)

Status of the device Signal strength/Battery remainder (only when the information comes from the device)

The Bluetooth icon lights up when the adapter is connected. ☞ page 48 : Buttons on the touch panel. In the explanation, they are indicated inside [ ].

[3 / 8] [7] Start and pause playback [4 ¢] Reverse/forward skip [5 ∞] Select the registered device (“New Device” appears when a new device can be registered.*3)

*1 When a cellular phone with audio function is connected, appears. *2 Indicates the button pressed. It may be different from the operation status. *3 You cannot select “New Device” when a Bluetooth audio player is connected.

You can use the following buttons on the remote controller for the Bluetooth audio operations.

Press [SOURCE], then press [Bluetooth AUDIO]. (☞ page 9) • You can also use SOURCE on the monitor panel. Press it repeatedly.

: Start and pause playback.

Reverse/forward skip Adjust the volume.

Bluetooth Information: If you wish to receive more information about Bluetooth, visit the following JVC web site: <http://www. jvc-victor.co.jp/english/car/> 36

EN_KW-AVX710[E]4.indb 36

07.12.7 10:44:27 AM MP3 indicator

Folder no./Track no./Playing time Ex. while playing an MP3 disc

ENGLISH Listening to the CD changer

Disc no. Tag data appears only when it is recorded.

Sound mode (☞ page 48)

Total track no. included on the disc [4 ¢] Press: Select track Hold: Reverse/forward search [5 ∞] Press: Select folders (only for MP3) Hold: Display Disc list

☞ page 38 : Buttons on the touch panel. In the explanation, they are indicated inside [

It is recommended to use a JVC MP3-compatible CD changer with your unit. • You can play only CDs (CD-DA) and MP3 discs.

Preparation: Make sure <Changer> is selected for <External Input>. (☞ page 55)

Select a disc to start playing.

Press [SOURCE], then press [CD-CH]. (☞ page 9)

• You can also use SOURCE on the monitor panel. Press it repeatedly.

To go to the other list

• If you select an MP3 disc, the Track list of the current folder appears. You can select a track and start playing. (☞ also page 22)

Display the Disc List.

• If you select a folder on the list, you can start playing the first track of the folder. 37

EN_KW-AVX710[E]4.indb 37

07.12.7 10:44:28 AM ENGLISH Selecting playback modes You can use following playback modes—Repeat or Random. Ex.: To select Track Repeat for an MP3 disc

Press [AV MENU]. Press [Mode].

When one of the playback modes is selected, the corresponding indicator lights up on the source information screen. To cancel, select <Off>.

Track: Repeats current track Disc: Disc: Repeats all tracks of the current disc All:

Randomly plays all tracks of the current disc Randomly plays all tracks of all loaded discs Track: Repeats current track Folder: Randomly plays all tracks of current Folder: Repeats all tracks of the current folder, then tracks of next folders folder Disc: Randomly plays all tracks of the Disc: Repeats all tracks of the current disc current disc All: Randomly plays all tracks of all loaded discs You can use the following buttons on the remote controller to operate the CD changer.

You can easily turn on or off Track Repeat by pressing [SHORT CUT] on the touch panel, then... ☞ page 48

: Select disc. : Select folder (MP3 only). • Press: Select track. • Hold: Reverse/forward search

EN_KW-AVX710[E]4.indb 38

07.12.7 10:44:29 AM ENGLISH Listening to the DAB tuner If no signal is received, “No DAB Signal” appears.

Band Sound mode (☞ page 48) DAB indicators */Standby Reception indicators

☞ page 42 : Buttons on the touch panel. In the explanation, they are indicated inside [ ].

* While tuning in a service with DLS (Dynamic Label Segment), the TEXT indicator lights up.

Press [SOURCE], then press [DAB]. (☞ page 9) • You can also use SOURCE on the monitor panel. Press it repeatedly.

Press [4] or [¢] to search for an ensemble—Auto Search. • Manual Search: Hold either [4]or [¢] until “Manual Search” appears on the screen, then press it repeatedly.

Press [∞] or [5] to select a service (either primary or secondary) to listen to.

EN_KW-AVX710[E]4.indb 39

07.12.7 10:44:29 AM ENGLISH When surrounding sounds are noisy

Display the Preset List.

Tune in to a service you want to preset.

Select a preset number.

Some services provide Dynamic Range Control (DRC) signals together with their regular programme signals. DRC will reinforce the low level sounds to improve your listening. • The DRC indicator will light up while tuning in to a service with the DRC signals.

The service selected in step 2 is now stored in preset number 2.

• As the number increases, the effect becomes stronger.

EN_KW-AVX710[E]4.indb 40

07.12.7 10:44:30 AM Activating/deactivating Announcement Standby Reception

Announcement Standby Reception allows the unit to switch temporarily to your favorite service (announcement type).

To activate, display <AV Menu> screen, then select <Mode>, press [On] for <Announce Standby>. (☞ below)

ANN ENGLISH Selecting preset services

The unit will temporarily switch to your Lights up favorite service from any source other than FM/AM.

Not yet activated. Tune in to another service providing the related signals.

Activating/deactivating TA/PTY Standby Reception

Press [AV MENU]. Press [Mode].

Operations are exactly the same as explained on page 14 for FM RDS stations. • You cannot store PTY codes separately for the DAB tuner and for the FM tuner. Announcement Standby Reception is now activated for PTY code <Transport News>: the initial setting.

Continued on the next page

07.12.7 10:44:30 AM ENGLISH Tracing the same programme— Alternative Frequency Reception (DAB AF)

You can easily activate and deactivate Announcement Standby Reception by pressing [SHORT CUT] on the touch panel, then... ☞ page 48 ☞ page 14

• While receiving a DAB service: When driving in an area where a service cannot be received, this unit automatically tunes in to another ensemble or FM RDS station broadcasting the same programme. • While receiving an FM RDS station: When driving in an area where a DAB service is broadcasting the same programme as the FM RDS station, this unit automatically tunes in to the DAB service.

To change the announcement type for Announcement Standby Reception

Select your favorite announcement type.

When shipped from the factory, Alternative Frequency Reception is activated. To deactivate the Alternative Frequency Reception, select <Off> for <DAB AF>. (☞ page 54)

Available announcement types: Transport News, Warning, News, Weather, Event, Special Event, Radio Info, Sports News, Financial News 42

EN_KW-AVX710[E]4.indb 42

07.12.7 10:44:31 AM ENGLISH Listening to the iPod Track no./Playing time

Sound mode (☞ page 48)

☞ page 44 [4 ¢] Press: Select track Hold: Reverse/forward search [5] Enter player’s menu [∞] Start playback/pause • To resume, press again.

: Buttons on the touch panel. In the explanation, they are indicated inside [ ].

It is required to connect the Interface adapter for iPod (KS-PD100) to the CD changer jack on the rear. Preparation: Make sure <iPod> is selected for <External Input>. (☞ page 55)

Press [SOURCE], then press [iPod] (☞ page 9) Playback starts automatically. • You can also use SOURCE on the monitor panel. Press it repeatedly.

Press [4] or [¢] to select a track.

Selecting a track from the player’s menu 1

Press [5] to enter the player’s menu. “SEARCH” flashes on the screen during menu operations. • This mode will be canceled if no operations are done for about five seconds.

Press [4] or [¢] to select the desired item. Press: Select an item. Hold: Skip ten items at a time if there are more than ten items.

Playlists Ô Artists Ô Albums Ô Songs Ô Genres Ô Composers Ô (back to the beginning)

Select an appropriate option.

Functions the same as “Repeat One.” Functions the same as “Repeat All.”

Album: Functions the same as “Shuffle Albums.” Song: Functions the same as “Shuffle Songs.”

Press [∞] to confirm the selection. • When the playback modes are selected, the corresponding indicators light up alternately on the screen.

Repeat steps 2 and 3 to select a track. • When a track is selected finally, playback starts. • To return to the previous menu, press [5].

To cancel, select <Off>.

Selecting playback modes 1

You can easily turn on or off Track Repeat by pressing [SHORT CUT] on the touch panel, then... ☞ page 48

07.12.7 10:44:32 AM ENGLISH Using other external components AV-INPUT You can connect an external component to the LINE IN/VIDEO IN terminals. Assigned title (☞ page 49)

Sound mode (☞ page 48)

You can easily access to <Aspect> setting menu by pressing [SHORT CUT] on the touch panel, then... ☞ page 48

: Buttons on the touch panel. In the explanation, they are indicated inside [ ]. These buttons also work when they are not shown on the touch panel (while watching the playback picture).

Press [SOURCE], then press [AV-IN]. (☞ page 9) • You can also use SOURCE on the monitor panel. Press it repeatedly.

Turn on the connected component and start playing the source.

To display the operation buttons (☞ page 20) while watching the playback picture

Touch the screen (center portion).

Touch the screen (center portion).

• If no operations are done for about five seconds, the operation buttons disappear. • [KEY] does not work when the source is “AV-IN.”

Continued on the next page

07.12.7 10:44:32 AM Navigation screen

ENGLISH You can also connect a Navigation System to the VIDEO IN terminal so that you can watch the navigation screen. Preparation: Make sure <Navigation> is selected for <AV Input>. (☞ page 55)

To view the navigation screen (and listen to the navigation guidance*) Press DISP on the monitor panel repeatedly. (☞ page 9) • The aspect ratio of the navigation screen is fixed to <Full> regardless of the <Aspect> setting. (☞ page 52)

* If your Navigation System is equipped with the voice guidance function.

To display the operation buttons (☞ page 20) while viewing the navigation screen • The operation buttons displayed on the screen vary among the playback sources.

Touch the screen (center portion).

Touch the screen (center portion).

• If no operations are done for about five seconds, the operation buttons disappear. • The above buttons except [KEY] also work when they are not shown on the screen (while viewing the navigation screen). When <Navigation> is selected for <AV Input> (☞ page 55) • You can use the source “AV-IN” for listening to an audio source connected to the LINE IN terminals. • Some status messages such as volume level will not appear on the screen.

EN_KW-AVX710[E]4.indb 46

07.12.7 10:44:33 AM You can connect an external component to the CD changer jack on the rear using the Line Input Adapter—KS-U57 (not supplied) or AUX Input Adapter—KS-U58 (not supplied). Assigned title (☞ page 49)

ENGLISH EXT-INPUT Sound mode (☞ page 48)

: Buttons on the touch panel. In the explanation, they are indicated inside [

Preparation: Make sure <External> is selected for <External Input>. (☞ page 55)

Press [SOURCE], then press [EXT-IN]. (☞ page 9) • You can also use SOURCE on the monitor panel. Press it repeatedly.

Turn on the connected component and start playing the source.

EN_KW-AVX710[E]4.indb 47

07.12.7 10:44:33 AM ENGLISH Sound equalization While playing back any source other than “Bluetooth PHONE,” you can easily access <Equalizer> menu by pressing [SHORT CUT] on the touch panel, then...

Storing your own adjustments You can store your adjustments into <User1>, <User2>, and <User3>.

Move to other six sound modes Ex.: When storing into <User2>.

EN_KW-AVX710[E]4.indb 48

07.12.7 10:44:33 AM ENGLISH Assigning titles to the sources

In the explanation, buttons on the touch panel are indicated inside [ ].

You can assign titles to “AV-IN” and “EXT-IN.”

Press [SOURCE], then press [AV-IN] or [EXT-IN]. (☞ page 9) • You can also use SOURCE on the monitor panel. Press it repeatedly.

Display <Title Entry> screen. You can enter up to 16 characters (for available characters, ☞ page 67). • [Store]: Confirm the entry. • [2/3]: Move the cursor. • [BS]: Erase the character before the cursor. • [Del]: Erase the character on the cursor. • [Cap]: Change the letter case (upper/ lower). • [Change]: Change the character set. • [Space]: Enter a space.

Finish the procedure.

07.12.7 10:44:34 AM ENGLISH Menu operations

The following steps are one of the fundamental procedures. Some of the settings do not open the sub-setting window, but just selecting an option will change the setting. • The display indications may change according to change of the specifications. Ex.: Changing the <AV Input> setting

Non-available items will be shaded.

Off: Cancels. On: Activates the demonstration on the screen. To stop it temporarily, touch the screen.

You can select the background picture of the screen. Horizon, Metal, Art, Plain

You can select the color of the background picture. Blue, Light-Blue, Red, Orange, Yellow, Green, Purple, Dark-Blue, Dark-Green, Brown, Light-Brown, Black

Off: Cancels. Once: Scrolls the disc information once. Auto: Repeats scrolling (five-second intervals). • Holding DISP on the monitor panel scrolls the information regardless of this setting.

Off: Cancels. On: Activates dimmer. Auto: Dims the monitor when you turn on the headlights.*1 Dimmer Time Set : Activates the Dimmer Time setting below.

Sets the Dimmer On/Off times.

You can select the brightness for dimmer. 1 (bright), 2 (middle), 3 (dark)

You can adjust brightness of the screen. –15 (darkest) to +15 (brightest); Initial 00

You can adjust the following to make the screen clear and legible for watching the playback picture. The setting will be stored—one for “DISC” (common) and the other for “AV-IN.” –15 to +15; Initial 0 Bright: Adjust if the picture is too bright or too dark. Contrast: Adjust the contrast. Color: Adjust the color of the picture—lighter or darker. • Press [5] or [∞] to adjust. • You cannot adjust <Tint>. (fixed)

ENGLISH The procedure for setting an item is shown on page 50.

Initial: Underlined *1 The ILLUMINATION lead connection is required. (☞ Installation/Connection Manual) *2 Adjustable only when the source is “DISC” (the inserted disc must contain pictures or movies) or “AV-IN.”

Selectable settings, [reference page] You can change the aspect ratio of the picture. Aspect ratio of incoming signal 4:3

• For “DISC”: Aspect ratio is automatically selected to match to the incoming signals. • For the other video sources: Aspect ratio is fixed to <Regular>.

Select the indication language shown on the screen. English, Español, Français, Deutsch, Italiano, Nederlands, Svenska, Dansk, Руccĸий, Português • The characters you can enter for assigning the titles also change according to the language selected, ☞ [67].

Select either 12-hour system or 24-hour system. 12Hours, 24Hours ☞ [8]

When <On> is selected, the clock time is displayed on the playback picture. Off, On

Select <Auto> to adjust the clock automatically using the clock time (CT) data from an FM RDS station. Off, Auto ☞ [8]

*1 Not adjustable when no picture is shown. *2 After you change the indication language setting, turn off then on the power so that your setting takes effect.

Select the initial disc menu language; Initial English (☞ also page 66).

Select the initial audio language; Initial English (☞ also page 66).

Select the initial subtitle language or erase the subtitle (Off); Initial English (☞ also page 66).

ENGLISH The procedure for setting an item is shown on page 50.

Select the monitor type to watch a wide screen picture on the external monitor. 16:9 : Select when the aspect ratio of the external monitor is 16:9. 4:3 LB (Letterbox)/4:3 PS (Pan Scan): Select when the aspect ratio of the external monitor is 4:3. • Refer to the illustrations on the left to see how the pictures are shown on the screen. Select the position of the on-screen bar. ☞ [28] 1: Higher position 2: Lower position

Select playback file type when a disc contains different types of files. Audio: Plays back audio files. Still Picture: Plays back JPEG files. Video: Plays back DivX/MPEG1/MPEG2 files. Audio&Video: Plays back audio files and DivX/MPEG1/MPEG2 files.

DivX Regist. (Registration)*3

This unit has its own Registration Code. Once you have played back a file with which the Registration Code recorded, this unit’s Registration Code is overwritten for copyright protection.

Select the signal format emitted through the DIGITAL OUT (optical) terminal. (☞ also page 65) PCM : Select this when connecting an amplifier or a decoder incompatible with Dolby Digital, DTS, or MPEG Audio, or when connecting to a recording device. Dolby D : Select this when connecting an amplifier or a decoder compatible with Dolby Digital. Stream : Select this when connecting an amplifier or a decoder compatible with Dolby Digital, DTS, or MPEG Audio.

*3 Selectable only for “DISC.” (Playback stops when you change the setting.) 53

EN_KW-AVX710[E]4.indb 53

07.12.7 10:44:36 AM ENGLISH Initial: Underlined Menu items 1

Selectable settings, [reference page] When playing back a multi-channel disc, this setting affects the signals reproduced through the LINE OUT terminals. Dolby SR : Select this to enjoy multi-channel surround audio by connecting an amplifier compatible with Dolby Surround. Stereo : Normally select this.

D. (Dynamic) Range Compres. (Compression)*1

You can enjoy a powerful sound at a low volume level while playing Dolby Digital software. Auto: Select to apply the effect to multi-channel encoded software. On: Select to always use this function.

Auto: Increases the tuner selectivity to reduce interference noises between adjacent stations. (Stereo effect may be lost.) Wide: Subject to the interference from adjacent stations, but sound quality will not be degraded and the stereo effect will remain.

When the received signals from the current station become weak... Off: Cancels—not selectable when <DAB AF> is set to <On>. AF Reg. (Regional): Switches to another station broadcasting the same programme. The REG indicator lights up. AF: Switches to another station. The programme may differ from the one currently received (the AF indicator lights up). ☞ [15]

00 to 30 or 50*2; Initial 15 ☞ [14]

*1 Selectable only for “DISC.” (Playback stops when you change the setting.) *2 Depends on the amplifier gain control. (☞ page 56) *3 Appears only when DAB tuner is connected.

EN_KW-AVX710[E]4.indb 54

You can determine the use of LINE IN and VIDEO IN terminals. ☞ [45, 46] Off: Select when no component is connected (“AV-IN” is skipped while selecting the source). Audio&Video: Select when connecting an AV component such as a VCR. Audio: Select when connecting an audio component such as a portable audio player. Camera*5 : Select when connecting a rear view camera. Navigation : Select when connecting a Navigation System.

For connecting an external component to the CD changer jack on the rear. Changer/iPod*7: CD changer or iPod. ☞ [37, 43] External: Any other than the above. ☞ [47] • For connecting the Bluetooth adapter and DAB tuner, this setting is not required. They are automatically detected.

Off: Cancels. On: Activates the key-touch tone.

Off: Cancels. Muting1, Muting2: Select either one which mutes the sounds while using the car phone system.

Off: Cancels. On: When the ignition is turned off, the lamp on the flashes.

ENGLISH The procedure for setting an item is shown on page 50.

Change the sensitivity of the touch panel. As the number decreases, sensitivity becomes higher. 1/2/3

Initialize all settings you have made in <AV Menu>. Press and hold [Enter] to initialize the settings, then reset the unit. ☞ [3]

*4 Not selectable when “AV-IN” is selected as the source. *5 The REVERSE GEAR SIGNAL lead connection is required. See Installation/Connection Manual. The rear view through the camera appears on the screen in <Full> aspect ratio (regardless of the aspect ratio setting) when you shift the gear to the reverse (R) position. When you press DISP on the control panel, or when you shift the gear to another position other than the reverse (R) position, the rear view screen is cleared. *6 Not selectable when the component connected to the CD changer jack is selected as the source. *7 The name of the component detected through the CD changer jack is shown. *8 The TEL MUTING lead connection is required. See Installation/Connection Manual. 55

EN_KW-AVX710[E]4.indb 55

Flat/Hard Rock/R&B/Pop/Jazz/Dance/Country/Reggae/Classic/User1/User2/User3 ☞ [48]

Selectable settings, [reference page]

Adjust fader—speaker output balance between the front and rear speakers. • Upmost—front only (F6) • Downmost—rear only (R6) When using a two-speaker system, set the fader to the center (0). Adjust balance—speaker output balance between the left and right speakers. • Leftmost—left only (L6) • Rightmost—right only (R6) Initial 0

Adjust and store auto-adjustment volume level for each source, comparing to the FM volume level. The volume level will automatically increase or decrease when you change the source. –12 to +12; Initial 00 • You can make the adjustments separately for DVD and other discs.

You can change the maximum volume level of this unit. Off: Deactivates the built-in amplifier. Low: VOL 00 to 30 (Select this if the maximum power of the speakers is less than 50 W.) High: VOL 00 to 50

Only for FM. (Local, DX) ☞ [11]

SSM Only for FM. Press and hold to start SSM. ☞ [11]

Only for “AV-IN” and “EXT-IN.” ☞ [49]

Only for DAB. (Initial Transport News) ☞ [42]

ENGLISH The procedure for setting an item is shown on page 50.

*1 Items listed under <Mode> vary among the playback sources.

List For “DISC”: Folder List and Track List (☞ page 22) For “CD-CH”: Disc List, Folder List, and Track List (☞ page 37) • For the other playback sources, you can display a list by pressing DISP on the monitor panel. (☞ page 9)

Select the method to make a call. ☞ [33]

You can read a message from the following message histories. Unread: Messages you have not read. Read: Messages you have read. Unsent: Messages you have not sent. Sent: Messages you have sent. • The number of messages in each history is also shown.

Only for “New Device.” Shows the list of Bluetooth devices which require some special procedure to establish Bluetooth connection. Select a device you want to connect. • After selecting the device, use <Open> or <Search> (☞ page 30 or 31) for connection. • Once the connection is established, it is registered in the unit. You can connect the unit and the device by using <Connect> (☞ below) from the next time.

Only for the registered devices. After selecting a device from among the registered devices (☞ pages 30 and 31), establish the connection with it.

Only for the device being connected. Disconnect the current device before connecting another device.

Only for the registered devices. Delete the registered devices.

*1 Selectable only for “Bluetooth PHONE” or “Bluetooth AUDIO.” Select a device (or “New Device”) before operating the menu. *2 Only for the device connected for “Bluetooth PHONE.” *3 Selectable only when the source is “Bluetooth PHONE” and the connected cellular phone is compatible with SMS (Short Message Service).

When operating the Bluetooth device, refer also to the instructions supplied with the device.

When the unit is turned on, the connection is established automatically with... Off: No Bluetooth device. Last: The last connected Bluetooth device. Order: The available registered Bluetooth device found first.

Off: The unit does not answer the calls automatically. Answer the calls manually. On: The unit answers the incoming calls automatically. Reject: The unit rejects all incoming calls.

Auto: The unit informs you of the arrival of a message by ringing and displaying “Receiving Message.” To read the message, ☞ page 33. Manual: The unit does not inform you of the arrival of a message.

Adjust microphone volume connected to the Bluetooth adapter. 01/02/03

The Bluetooth software and hardware versions are shown.

ENGLISH The procedure for setting an item is shown on page 50.

Initial: Underlined *4 Selectable only for “Bluetooth PHONE.” *5 Only for the cellular phone connected for “Bluetooth PHONE.” Not selectable when “New Device” is selected. *6 If you wish to receive more information about Bluetooth, visit the following JVC web site: <http://www.jvc-victor. co.jp/english/car/>

Moisture may condense on the lens inside the unit in the following cases: • After starting the heater in the car. • If it becomes very humid inside the car. Should this occur, the unit may malfunction. In this case, eject the disc and leave the unit turned on for a few hours until the moisture evaporates.

A dirty disc may not play correctly. If a disc does become dirty, wipe it with a soft cloth in a straight line from center to edge. • Do not use any solvent (for example, conventional record cleaner, spray, thinner, benzine, etc.) to clean discs.

To play new discs Center holder

When removing a disc from its case, press down the center holder of the case and lift the disc out, holding it by the edges. • Always hold the disc by the edges. Do not touch its recording surface. When storing a disc into its case, gently insert the disc around the center holder (with the printed surface facing up). • Make sure to store discs into the cases after use.

New discs may have some rough spots around the inner and outer edges. If such a disc is used, this unit may reject the disc. To remove these rough spots, rub the edges with a pencil or ball-point pen, etc.

Do not use the following discs: SingleCD—8 cm disc

Sticker and sticker residue

C-thru Disc (semi-transparent disc)

Transparent or semi-transparent on its recording area

• This unit can recognize a total of 5 000 files and 250 folders (a maximum of 999 files per folder). • Use only “finalized” discs. • This unit can play back multi-session discs; however, unclosed sessions will be skipped while playing. • This unit can recognize a total 25 characters for file/ folder names. • Some discs or files may not be played back due to their characteristics or recording conditions.

Turning on the power • By pressing SOURCE on the monitor panel, you can also turn on the power. If the source is ready, playback starts.

Tuner (FM only) Storing stations in memory • When SSM is over, received stations are preset in no. 1 (lowest frequency) to no. 6 (highest frequency).

ENGLISH More about this unit

• For details about DVD-VR format and Playlist, refer to the instructions supplied with the recording equipment.

General • In this manual, words “track” and “file” are interchangeably used. • This unit can only play back audio CD (CD-DA) files if different type of audio files (MP3/WMA/WAV) are recorded on the same disc. • This unit can display only one-byte characters. No other characters can be correctly displayed.

File playback Playing DivX files • This unit can play back DivX files with the extension code <.divx>, <.div>, or <.avi> (regardless of the letter case—upper/lower). • This unit supports the DivX files whose resolution is 720 x 576 pixels or less. • Audio stream should conform to MP3 or Dolby Digital. • The file encoded in the interlaced scanning mode may not be played back correctly. • The maximum bit rate for video signals (average) is 4 Mbps.

Inserting a disc • When a disc is inserted upside down or has no playable files, “Cannot play this disc Check the disc” appears on the screen. Eject the disc.

Ejecting a disc • If “No disc“ appears after removing a disc, insert a disc or select another playback source. • If the ejected disc is not removed within 15 seconds, the disc is automatically inserted again into the loading slot to protect it from dust.

Continued on the next page

EN_KW-AVX710[E]4.indb 61

REFERENCES 07.12.7 10:44:41 AM

• This unit can play back files recorded in VBR (variable bit rate). • Files recorded in VBR have a discrepancy in elapsed time indication. • This unit cannot play back the following files: – MP3 files encoded with MP3i and MP3 PRO format. – MP3 files encoded with Layer 1/2. – WMA files encoded with lossless, professional, and voice format. – WMA files which are not based upon Windows Media® Audio. – WMA files copy-protected with DRM. – Files which have the data such as AIFF, ATRAC3, etc.

ENGLISH Playing MPEG1/MPEG2 files • This unit can play back MPEG1/MPEG2 files with the extension code <.mpg>, <.mpeg>, or <.mod>*. * <.mod> is an extension code used for the MPEG2 files recorded by JVC Everio camcorders. • The stream format should conform to MPEG system/ program stream. The file format should be MP@ML (Main Profile at Main Level)/SP@ML (Simple Profile at Main Level)/ MP@LL (Main Profile at Low Level). • Audio streams should conform to MPEG1 Audio Layer-2 or Dolby Digital. • The maximum bit rate for video signals (average) is 4 Mbps.

Disc/file information shown on the external monitor

• This unit can play back JPEG files with the extension code <.jpg>, or <.jpeg>. • It is recommended that you record a file at 640 x 480 resolution. • This unit can play back baseline JPEG files. Progressive JPEG files or lossless JPEG files cannot be played.

The following screens appear only on the external monitor.

• CD T. RPT Playing MP3/WMA/WAV files • This unit can play back files with the extension code <.mp3>, <.wma>, or <.wav> (regardless of the letter case—upper/lower). • This unit can play back the files meeting the conditions below: – Bit rate: MP3/WMA: 32 kbps — 320 kbps – Sampling frequency: 48 kHz, 44.1 kHz, 32 kHz (for MPEG1) 24 kHz, 22.05 kHz, 16 kHz (for MPEG2) 48 kHz, 44.1 kHz, 32 kHz, 22.05 kHz (for WMA) 44.1 kHz (for WAV) • This unit can show ID3 Tag Version 1.0/1.1/2.2/2.3/2.4 (for MP3). • This unit can also show WAV/WMA Tag.

Track Information Album Four seasons Artist Robert M. Smith Title Rain

Track : 6 / 14 Cloudy Fair Fog Hail Indian summer Rain Shower Snow Thunder Typhoon Wind Winter sky

Selected playback mode Elapsed playing time of the current track Operation status Current track number/total number of tracks on the disc 5 Track information 6 Track list 7 Current track (highlighted bar)

• While driving, do not perform complicated operation such as dialing the numbers, using phone book, etc. When you perform these operations, stop your car in a safe place. • Some Bluetooth devices may not be connected to this unit depending on the Bluetooth version of the device. • This unit may not work for some Bluetooth devices. • Connecting condition may vary depending on circumstances around you. • When the unit is turned off, the device is disconnected.

Current folder (highlighted bar) Current folder number/total folder number Folder list Selected playback mode Elapsed playing time of the current track (not displayed for JPEG) Operation status Current track number/total number of tracks in the current folder (total number of tracks on the disc) Track information (only for MP3/WMA/WAV) Track list Current track (highlighted)

ENGLISH Bluetooth operations General

Warning messages for Bluetooth operations • Connection Error: The device is registered but the connection has failed. Use <Connect> to connect the device again. (☞ page 31) • Error: Try the operation again. If “Error” appears again, check if the device supports the function you have tried. • Device Unfound: No available Bluetooth device is detected by <Search>. • Loading: The unit is updating the phone book and/ or SMS. • Please Wait...: The unit is preparing to use the Bluetooth function. If the message does not disappear, turn off and turn on the unit, then connect the device again (or reset the unit). • Reset 08: Check the connection between the adapter and this unit.

* If tag data includes “Jacket Picture” (baseline JPEG), it will be displayed.

Icons for phone types • These icons indicate the phone type set on the device.

• If you select a folder, which does not include any music files, on the list (☞ page 37), you will hear a beep. Select another folder including music files.

• If you change the <Amplifier Gain> setting from <High> to <Low> while the volume level is set higher than “30,” the unit automatically changes the volume level to “VOL 30.” • After you change any of <Menu Language/Audio Language/Subtitle> settings, turn off then on the power, and re-insert the disc (or insert another disc) so that your setting takes effect. • When you select <16:9> for a picture whose aspect ratio is 4:3, the picture slightly changes due to the process for converting the picture width. • Even if <4:3PS> is selected, the screen size may become <4:3LB> for some discs.

DAB tuner • Only the primary DAB service can be preset even when you store a secondary service.

iPod operations • You can control the following types of iPods through the interface adapter. – iPod with dock connector (3rd Generation) – iPod with Click Wheel (4th Generation) – iPod mini – iPod photo – iPod nano *1 – iPod video (5th Generation) *2 *1 When you connect the iPod nano to the interface adapter, be sure to disconnect the headphones; otherwise, no sound is heard. *2 It is not possible to browse video files on the “Videos” menu while the iPod is connected to the interface adapter. • If the iPod does not play correctly, please update your iPod software to the latest version. For details about updating your iPod, visit <http://www.apple.com>. • When you turn on this unit, the iPod is charged through the adapter connected to this unit. • While the iPod is connected, all operations from the iPod are disabled. Perform all operations from this unit. • The text information may not be displayed correctly. • The text information scrolls on the screen. This unit can display up to 40 characters. Notice: When operating an iPod, some operations may not be performed correctly or as intended. In this case, visit the following JVC web site: <http://www.jvc.co.jp/english/car/support/ ks-pd100/index.html>

EN_KW-AVX710[E]4.indb 64

2-channel signal is emitted. When playing multi-channel encoded disc, multi-channel signals are downmixed. • DTS sound cannot be reproduced.

Through the DIGITAL OUT terminal

ENGLISH Sound signals emitted through the rear terminals Through the analog terminals (Speaker out/REAR OUT)

Digital signals (Linear PCM, Dolby Digital, DTS, MPEG Audio) are emitted. • To reproduce the multi-channel sounds such as Dolby Digital, DTS, and MPEG Audio, connect an amplifier or a decoder compatible with these multi-channel sources to this terminal, and set <D. Audio Output> correctly. (☞ page 53) Output signals

<D. Audio Output> Playback disc DVD

48 kHz, 16/20/24 bits Linear PCM

with Dolby Digital with DTS with MPEG Audio

48 kHz, 16 bits stereo Linear PCM Audio CD with DTS DTS bitstream

32/44.1/48 kHz, 16 bits Linear PCM MP3/WMA

32/44.1/48 kHz, 16 bits Linear PCM WAV

44.1 kHz, 16 bits Linear PCM

* Digital signals may be emitted at 20 or 24 bits (at their original bit rate) through the DIGITAL OUT terminal if the discs are not copy-protected.

00 00 00 00 +01 –02 00 +01 00 00

Persian Finnish Fiji Faroese Frisian Irish Scots Gaelic Galician Guarani Gujarati Hausa Hindi Croatian Hungarian Armenian Interlingua Interlingue Inupiak Indonesian Icelandic Hebrew Japanese Yiddish Javanese Georgian

• Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. • “DTS” and “DTS Digital Out” are registered trademarks of DTS, Inc • “DVD Logo” is a trademark of DVD Format/Logo Licensing Corporation registered in the US, Japan and other countries. • DivX, DivX Ultra Certified, and associated logos are trademarks of DivX, Inc. and are used under license. • Official DivX® Ultra Certified product • Plays all versions of DivX® video (including DivX® 6) with enhanced playback of DivX® media files and the DivX® Media Format • Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. • The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Victor Company of Japan, Limited (JVC) is under license. Other trademarks and trade names are those of their respective owners. • iPod and iTunes are trademarks of Apple Inc., registered in the U.S. and other countries. • This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

Upper and lower cases

• When any language other than <Руccĸий> is selected for <Language>. (☞ page 52) Upper and lower cases

ENGLISH Characters shown on the screen In addition to the roman alphabet (A – Z, a – z), you can use the following characters to assign titles. (☞ page 49) • When <Руccĸий> is selected for <Language>. (☞ page 52)

07.12.7 10:44:45 AM ENGLISH Troubleshooting What appears to be trouble is not always serious. Check the following points before calling a service center. • For operations with the external components, refer also to the instructions supplied with the adapters used for the connections (as well as the instructions supplied with the external components). Symptoms • No sound comes out of the speakers.

• The screen is not clear and legible.

• “Position Error Push Open Key” appears on the screen. • “Mecha Error Push Reset” appears on the screen, and the panel does not move. • “No Signal” appears.

Remedies/Causes • Adjust the volume to the optimum level. • Check the cords and connections. • DTS sound cannot be reproduced through the analog terminals (Speaker out/REAR OUT). Sunshine from the windscreen may cause this symptom. Adjust <Bright>. (☞ page 51) The monitor panel angle has been forcibly adjusted, or its adjustment has been interrupted while opening or closing. Press OPEN/TILT. Reset the unit. (☞ page 3)

• The buttons on the monitor panel do not work. • The unit does not work at all. • SSM automatic presetting does not work.

• Change the source. • Start the playback on the external component connected to VIDEO IN terminal. • Check the cords and connections. • Signal input is too weak. When the monitor panel is open, only +/– (volume) and OPEN/TILT work. The other buttons do not function. Reset the unit. (☞ page 3) Store stations manually. (☞ page 11)

• Static noise while listening to the radio.

Connect the aerial firmly.

EN_KW-AVX710[E]4.indb 68

07.12.7 10:44:45 AM Disc in general

• Disc can be neither recognized nor played back. • Disc cannot be ejected. • Recordable/Rewritable discs cannot be played back. • Tracks on the Recordable/Rewritable discs cannot be skipped. • Playback does not start. • • •

Remedies/Causes Eject the disc forcibly. (☞ page 3) Unlock the disc. (☞ page 22) • Insert a finalized disc. • Finalize the discs with the component which you used for recording.

• Insert the disc correctly again. • The format of files is not supported by the unit. The playback picture is not clear and legible. Adjust items in <Picture Adjust> menu. (☞ page 51) Sound and pictures are sometimes • Stop playback while driving on rough roads. interrupted or distorted. • Change the disc. No playback picture is shown and “Parking Parking brake lead is not connected properly. Brake” appears on the screen, even when the (☞ Installation/Connection Manual) parking brake is engaged. No picture appears on the external monitor. • Connect the video cord correctly. • Select the correct input on the external monitor. “Eject Error” or “Loading Error” appears on Change the source by pressing SOURCE. the screen. “Region code error” appears on the screen Region code is not correct. (☞ page 4) when you insert a DVD Video. Disc cannot be played back. • Change the disc. • Record the tracks using a compliant application on the appropriate discs. (☞ page 4) • Add appropriate extension codes to the file names. Noise is generated. The track played back is not a playable file format. Skip to another file. Tracks are not played back as you have Playback order may differ from that played back using intended them to play. other players. Elapsed playing time is not correct. This sometimes occurs during playback. This is caused by how the tracks are recorded. “Not Support” appears on the screen and The track is unplayable. track skips.

Continued on the next page

• Bluetooth device does not detect the unit.

• The unit does not detect the Bluetooth device.

• The unit does not make pairing with the Bluetooth device.

• Echo or noise occurs. • Phone sound quality is poor.

• The sound is interrupted or skipped during playback of a Bluetooth audio player.

• “New Device” cannot be selected for “Bluetooth AUDIO.” • The connected audio player cannot be controlled. • “Reset 08” appears on the screen.

Remedies/Causes This unit can be connected with one Bluetooth cellular phone and one Bluetooth audio player at a time. While connected to a device, this unit cannot be detected from another device. Disconnect currently connected device and search again. • Check the Bluetooth setting of the device. • Search from the Bluetooth device. After the device detects the unit, select <Open> on the unit to connect the device. (☞ page 30) • Enter the same PIN code for both the unit and target device. If the PIN code of the device is not indicated on its instructions, try “0000” or “1234.” • Select the device name from <Special Device>, then try to connect again. (☞ pages 31, 58) Adjust the microphone unit position. • Reduce the distance between the unit and the Bluetooth cellular phone. • Move the car to place where you can get a better signal reception. • Reduce the distance between the unit and the Bluetooth audio player. • Disconnect the player connected for “Bluetooth PHONE.” • Turn off, then turn on the unit. • (When the sound is not yet restored,) connect the player again. Bluetooth audio player is already connected. To select “New Device,” disconnect it. (☞ page 31) Check whether the connected audio player supports AVRCP (Audio Video Remote Control Profile). Check the connection between the adapter and this unit.

EN_KW-AVX710[E]4.indb 70

• “Reset 01” – “Reset 07” appears on the screen. • The CD changer does not work at all. • “No DAB Signal” appears on the screen. • “Reset 08” appears on the screen. • The DAB tuner does not work at all. • “Antenna Power NG” appears on the screen. • The iPod does not turn on or does not work.

• Sound is distorted. • “Disconnect” appears on the screen. • Playback stops. • “No Files” appears on the screen. • “Reset 01” – “Reset 07” appears on the screen. • “Reset 08” appears on the screen. • The iPod’s controls do not work after disconnecting from this unit. • No picture appears on the screen. • Playback picture is not clear and legible.

Remedies/Causes Insert a disc into the magazine. Insert the magazine. Current disc does not include playable files. Replace the disc with one including playable files. Connect this unit and the CD changer correctly and press the reset button of the CD changer. Press the reset button of the CD changer. Reset the unit. (☞ page 3) Move to an area with stronger signals. Connect this unit and the DAB tuner correctly, then reset the unit. (☞ page 3) Connect this unit and the DAB tuner correctly, then reset the unit. (☞ page 3) Check the cords and connections. • Check the connection. • Charge the battery. Deactivate the equalizer either on this unit or the iPod. Check the connection. The headphones are disconnected during playback. Restart playback. No tracks are stored. Import tracks to the iPod. Disconnect the adapter from both this unit and iPod. Then, connect them again. Check the connection between the adapter and this unit. Reset the iPod. • Turn on the video component if it is not on. • Connect the video component correctly. Adjust items in <Picture Adjust> menu. (☞ page 51)

EN_KW-AVX710[E]4.indb 71

Symptoms • “No Disc” appears on the screen. • “No Magazine” appears on the screen. • “Cannot play this disc Check the disc” appears on the screen. • “Reset 08” appears on the screen.

07.12.7 10:44:46 AM ENGLISH Specifications Maximum Power Output: Continuous Power Output (RMS):

Line-Out Level/Impedance: Output Impedance:

50 W per channel 20 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more than 0.8% total harmonic distortion 4 Ω (4 Ω to 8 Ω allowance) 60 Hz, 150 Hz, 400 Hz, 1 kHz, 2.5 kHz, 6.3 kHz, 15 kHz ±10 dB 70 dB 2.5 V/20 kΩ load (full scale) 1 kΩ PAL 1 Vp-p/75 Ω LINE IN, VIDEO IN, Aerial input

CD changer, OE REMOTE, Reverse gear signal, DIGITAL OUT (optical)

87.5 MHz to 108.0 MHz

(MW) 522 kHz to 1 620 kHz (LW) 144 kHz to 279 kHz

11.3 dBf (1.0 μV/75 Ω)

50 dB Quieting Sensitivity:

16.3 dBf (1.8 μV/75 Ω)

Alternate Channel Selectivity (400 kHz):

65 dB Frequency Response:

Sensitivity/Selectivity:

Non-contact optical pickup (semiconductor laser)

FM/AM TUNER Frequencies: Level:

Signal-to-Noise Ratio: Audio Output Level REAR OUT: Color System: Video Output (composite): Other Terminals:

DVD/CD Front/Rear: Front/Rear:

93 dB Signal-to-Noise Ratio:

95 dB Wow and Flutter:

Less than measurable limit

TFT (Thin Film Transistor) active matrix format

DC 14.4 V (11 V to 16 V allowance)

Allowable Storage Temperature:

–10°C to +60°C Allowable Operating Temperature:

0°C to +40°C Dimensions (W × H × D): • With trim plate and sleeve attached

Installation Size (approx.):

182 mm × 111 mm × 160 mm

Panel Size (approx.):

188 mm × 117 mm × 10 mm

2.9 kg (including trims and sleeve)

Required space for the monitor ejection

CAUTION: When ejecting the monitor, leave an open space for the monitor to come out. If you do not, the monitor may obstruct the steering wheel and gearshift lever operations, and this may result in a traffic accident. Unit: mm

Design and specifications are subject to change without notice.

Demonstration (Demonstration)

Off: Hebt auf. On: Aktiviert die Demonstration auf dem Bildschirm. Zum zeitweiligen Unterbrechen berühren Sie den Bildschirm.

Wall Paper (Hintergrund)

AF Regional (AF Regional)

Flat/Hard Rock/R&B/Pop/Jazz/Dance/Country/Reggae/Classic/User1/User2/User3 ☞ [48]

Track Information Album Four seasons Artist Robert M. Smith Title Rain

Track : 6 / 14 Cloudy Fair Fog Hail Indian summer Rain Shower Snow Thunder Typhoon Wind Winter sky

48 kHz, 16/20/24 Bit Linear-PCM

48 kHz, 16 Bit Stereo-Linear-PCM*

48 kHz, 16 Bit Stereo-Linear-PCM

DTS Bitstrom MPEG Bitstrom

48 kHz, 16 Bit Stereo-Linear-PCM

32/44,1/48 kHz, 16 Bit Linear-PCM MP3/WMA

32/44,1/48 kHz, 16 Bit Linear-PCM WAV

44,1 kHz, 16 Bit Linear-PCM

00 00 00 00 +01 –02 00 +01 00 00

Aspect (Format Image)*

4:3PS OSD Position (Position OSD)*3

Off, On ☞ [15] Off, On ☞ [42]

Flat/Hard Rock/R&B/Pop/Jazz/Dance/Country/Reggae/Classic/User1/User2/User3 ☞ [48]

Track Information Album Four seasons Artist Robert M. Smith Title Rain

Track : 6 / 14 Cloudy Fair Fog Hail Indian summer Rain Shower Snow Thunder Typhoon Wind Winter sky

48 kHz, 16/20/24 bits Linear PCM

32/44,1/48 kHz, 16 bits Linear PCM MP3/WMA

32/44,1/48 kHz, 16 bits Linear PCM WAV

44,1 kHz, 16 bits Linear PCM

00 00 00 00 +01 –02 00 +01 00 00

11,3 dBf (1,0 μV/75 Ω)

Beschikbare PTY-codes: News, Current Affairs, Information, Sport, Education, Drama, Cultures, Science, Varied Speech, Pop Music, Rock Music, Easy Listening, Light Classics M, Serious Classics, Other Music, Weather & Metr, Finance, Children’s Progs, Social Affairs, Religion, Phone In, Travel & Touring, Leisure & Hobby, Jazz Music, Country Music, National Music, Oldies Music, Folk Music, Documentary

OSD Clock (OSD Klok)

Monitor Type (Type Monitor)*3

4:3PS OSD Position (OSD Instelling)*3 Position 2

DX/Local (DX/Lokaal)

Auto Connect (Auto Connect) *

Track Information Album Four seasons Artist Robert M. Smith Title Rain

Track : 6 / 14 Cloudy Fair Fog Hail Indian summer Rain Shower Snow Thunder Typhoon Wind Winter sky

48 kHz, 16/20/24 bit lineair PCM

48 kHz, 16 bit stereo lineair PCM*

48 kHz, 16 bit stereo lineair PCM

Dolby Digital bitstream

48 kHz, 16 bit stereo

<D. Audio Output> Weergavedisc

48 kHz, 16 bit stereo lineair PCM

32/44,1/48 kHz, 16 bit lineair PCM MP3/WMA

32/44,1/48 kHz, 16 bit lineair PCM WAV

44,1 kHz, 16 bit lineair PCM

00 00 00 00 +01 –02 00 +01 00 00

11,3 dBf (1,0 μV/75 Ω)

11/29/07 11:23:26 AM Having TROUBLE with operation? Please reset your unit Refer to page of How to reset your unit

EN, GE, FR, NL © 2008 Victor Company of Japan, Limited