IAN 113908 - Lighting Livarno Lux - Free user manual and instructions

Product Type	LED Ceiling Light with Remote Control
Brand	Livarno Lux
Model	IAN 113908
Number of Lights	6
Bulb Type	LED, E14 base, 3 W each
Maximum Total Power	18 W (6 x 3 W)
Operating Voltage	230-240 V ~, 50 Hz
Protection Class	I
Remote Control Receiver	220-240 V ~, 50 Hz, max. load 1000 W, 433.92 MHz
Remote Control Transmitter	12 V DC, battery type A23, 433.92 MHz
Intended Use	Indoor, dry and enclosed spaces only
Dimmer Compatibility	Not suitable for dimmer or electronic switches
Minimum Distance from Illuminated Object	0.5 m
Installation	Must be installed by qualified electrician
Maintenance	Clean with dry, lint-free cloth; do not use water or solvents
Bulb Replacement	Only use 220-240 V ~ LED lamps, max. 3 W, E14 base
Battery for Remote	Type A23, 12 V DC
Guarantee	3 years from date of purchase
Manufacturer	59929 Brilon, Germany

Frequently Asked Questions - IAN 113908 Livarno Lux

How do I install the Livarno Lux ceiling light?

Installation must be performed by a qualified electrician. Disconnect power at the fuse box. Mark and drill holes, insert dowels, and mount the bracket. Connect the mains cable via the terminal block (L, N, earth). Secure the light fixture and attach the lamp glasses with the threaded ring using the provided tool.

What type of bulbs does this light use?

It uses LED bulbs with E14 base, 220-240 V~, maximum 3 W each. Only replace with identical type.

How do I replace a bulb?

First, disconnect power by switching off the circuit breaker. Allow the lamp to cool completely. Remove the lamp glass by unscrewing the threaded ring. Carefully rotate the defective bulb anticlockwise out of the socket. Insert a new bulb clockwise and reattach the lamp glass.

Why isn't my remote control working?

Check the battery in the remote control. It should be type A23, 12 V DC, inserted with correct polarity. If the battery is fine, try switching the light off via the wall switch, wait 15-20 seconds, then switch on again. If still no response, replace the battery.

Can I use this light with a dimmer?

No, this light is not suitable for dimmer or electronic switches. Use only the supplied remote control or a standard wall switch.

How do I clean the ceiling light?

Disconnect the light from mains supply and allow it to cool. Use a dry, lint-free cloth. Never use water, solvents, or abrasive cleaners.

What should I do with the packaging?

The packaging is made of environmentally-friendly materials and can be disposed of at local recycling facilities.

How do I dispose of the old light or batteries?

The product must not be disposed of with household waste. Take it to a recycling collection point for electrical and electronic appliances. Batteries should be removed and disposed of separately at appropriate collection points.

What is the warranty period?

The product has a 3-year guarantee from the date of purchase. It covers material and manufacturing defects, but not wear parts or damage from improper use.

Where can I find the user manual in PDF?

You can download the free PDF manual for the Livarno Lux IAN 113908 from websites like notice-facile.com or the manufacturer's support page.

USER MANUAL IAN 113908 Livarno Lux

Operation and Safety Notes

SE

LED-TAKLAMPA

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device.

FI

GB / IE Operation and Safety Notes Page 5

Introduction

Proper use....Page 6

Included items Page 6

Description of parts and features......Page 6

Technical details....Page 6

Safety

Safety advice......Page 6

Preparation

Required tools and materials....Page 7

Before installation Page 8

Installation

Fitting the light Page 8

Preparing the product for use

Inserting / replacing batteries....Page 8

Switching the light on/off....Page 9

Replacing a bulb....Page 9

Maintenance and cleaning......Page 9

Disposal Page 9

Guarantee and service

Guarantee declaration Page 10

Service address......Page 10

Declaration of conformity....Page 10

Manufacturer......Page 10

LED ceiling light

- Introduction

We congratulate you on the purchase of your new device. You have chosen a high quality product. Please read carefully and completely through these operating instructions. Fold out the page with the illustrations. These instructions form part of the product and contain important information about bringing the product into use and its handling. Always observe all the safety advice. Check that the correct mains voltage is available and that all the parts have been properly assembled before bringing into use. Should you have any questions or be uncertain as to how to operate the device, please get in touch with your dealer or service point. Please keep these instructions in a safe place and hand them on to a third party if necessary.

- Proper use

This light is suitable only for interior use, in dry and enclosed spaces. The light can be fitted to all normally inflammable surfaces. This lamp is intended for use only in a domestic environment.

- Included items

Check that all the items and accessories are present and that the lamp is in perfect condition immediately after unpacking.

1 Ceiling light, model 14104202L (6-light)
6 LED bulbs E14, 3 W
6 Lamp glasses
1 Remote control handset
1 Battery, 12 V—, A23
2 Dowels
2 Screws
1 Tool
1 Operating instructions

• Description of parts and features

1 Mounting bracket with elongated holes
2 Screws
3 Mains connection cable (external)
4 Terminal block
5 Receiver
6 Connection enclosure
7 Spot
8 Remote control handset
9 Fitting (socket)
10 Lamp glass
11 Threaded ring
12 Tool
13 Bulb
14 Dowel
15 Protective tubes

- Technical details

Ceiling light:

Operating voltage: 230-240V\~, 50Hz

LED bulb: 220-240V\~, 3W, E14

Maximum nominal output: 6 x 3 W

Protection class: I

Remote control receiver:

Rated voltage: 220-240V\~, 50Hz

Max. load capacity: 1000 W

Frequency: 433.92 MHz

Remote control transmitter:

Operating voltage: 12V ——, A23

Frequency: 433.92 MHz

- Safety

Safety advice

The right to claim under the guarantee shall be rendered invalid in respect of damage caused by the non-observance of these operating instructions! No liability is accepted for consequent damage!

No liability is accepted for damage to property or persons caused by improper handling or non-observance of the safety advice!

To avoid danger to life from electric shock

■ Ensure that a qualified electrician or a person trained to carry out electrical installations performs the electrical installation.
Every time before connecting the lamp the mains, check it and the mains lead for damage. Never use your light if you find it is damaged in any way.

CAUTION! A damaged mains lead presents a serious danger to life from electric shock. In the event of damage, repairs or other problems with the lamp please contact the service centre or an electrician.

Before installation, remove the fuse for this circuit or switch off at the circuit breaker (0 setting) in the fuse box.
Before assembly, ensure that the mains voltage available corresponds to the operating voltage necessary of the light (230-240 V \~).
■ Never let the lamp come into contact with water or other liquids.
Never open or insert anything into electrical fittings or equipment. Doing this sort of thing can lead to a serious danger to life from electric shock.
Do not install the lamp on a moist and conductive surface!

To avoid danger of fire and injury

RISK OF INJURY! Check every bulb and lampshade for damage immediately upon unpacking.

Do not fit the light if the bulbs and / or lamp-shades are faulty. If they are, contact the service point for a replacement.
RISK OF INJURY FROM BURNS! Ensure the lamp has been switched off and allowed to cool before you

touch it. In this way you will avoid the danger of burns. Bulbs give off a lot of heat around the top of the lamp.

• Allow the lamp to cool down completely.
• Replace any faulty bulbs with new ones immediately. Before replacing the bulb, always remove the fuse or switch the automatic cutout off.

FIRE HAZARD! Fit the light so that it is at least 0.5 m away from the material illuminated. Fire can result from the development of too much heat.

Do not allow the lamp or the packaging materials to lie around unattended. Plastic film or bags, Styrofoam etc. can turn into dangerous toys for children.
This light is not suitable for dimmer or electronic switches.
Do not look directly in to the light source (lamp, LED, etc.).

Safe working

■ Onlyuse 220-240V \~ LED lamps with E14 base and a maximum output of 3 Watt.
Fit the light in such a way to ensure it is protected from damp and dirt.
■ Make careful preparations for the assembly and take sufficient time. Clearly lay out all components and any additional tools or materials that might be required so that they are readily to hand.
- Remain alert at all times and always watch what you are doing. Always proceed with caution and do not assemble the lamp if you cannot concentrate or feel unwell.

● Preparation

- Required tools and materials

The tools and materials mentioned are not included in the delivery. The details and values given are non-binding and for guidance only.

The nature of the material depends on the individual circumstances on site.

Preparation / Before installation / Installation / Preparing the product for use

• Pencil / Marking tool
• Voltage tester
• Screwdriver
• Electric drill
• Drill (ø approx. 0.6 cm)
• Edge cutter
• Ladder

- Before installation

Important: The electrical connection must be carried out by a qualified electrician or someone trained to perform electrical installations. This person must be familiar with the features of the light and the connection requirements.

Familiarise yourself with all instructions and diagrams in this manual as well as with the light before installation.
Before installation, ensure that the cable that the light is to be attached to is not live. Remove its fuse or switch off the automatic cutout in the fuse box (0 position).
☐ Use the voltage tester to check that there is no voltage.

- Installation

- Fitting the light

Remove the screws visible on the side of the terminal housing 6 and take the installation frame 1 on the back off (see diagram).
☐ Mark the boreholes using the slotted holes provided for the screws in the installation frame 1.
Now drill the screw holes (approx. 6 mm, depth approx. 40 mm). Ensure that the feed cable is not damaged.
☐ Insert the dowels into the drilled holes. Fasten the mounting bracket 1 in place with the supplied screws.
☐ Feed the power cord (external) through the protective tubes 15 (see fig.).
☐ Connect the mains cable (external) 3 via lustre terminal 4.

☐ Ensure that the cables have been connected in line with the correct colour coding (conductive wire, black or brown = symbol L, neutral wire, blue = symbol N).
Now connect the earthed conductor (green-yellow) to the earth terminal labelled in the terminal housing 6 (see diagram).
☐ Screw the light onto the installation frame using the screws 2.
☐ Loosen the threaded ring 11.
Place the lamp glass carefully over the fitting 9 and fasten it in place by tightening the threaded ring 11 using the supplied tool 12.

Ensure it is correctly seated.

☐ Use a clean, fluff-free cloth when you are replacing a bulb 13.
☐ Rotate the bulb carefully clockwise into the fitting. Check that the bulb is correctly seated.
☐ Replace the fuse or switch on the circuit breaker (Position I) inside the fuse box.

Your light is now ready for operation.

● Preparing the product for use

- Inserting / replacing batteries

☐ Release the screw from the battery compartment of the remote control handset 8 (rear side) by unscrewing it with a crosshead screwdriver in the direction.
☐ Remove the used battery, if present.
☐ Insert a new battery into the battery compartment. Use batteries type A23, 12 V--- only.

Note: Make sure you fit the battery the right way round (polarity). The correct polarity is shown inside the battery compartment.

☐ Close the battery compartment of the remote control handset 8 (rear side) by screwing the screw in with a Phillips screwdriver in the C direction.

- Switching the light on / off

You have the choice of operating the light from an ordinary wall switch or switching it on and off using the supplied remote control unit.

Switching the light on / off using the remote control handset:

• The wall switch is in the normal position (OFF).
  ☐ Press the wall switch (ON).
  ☐ Press the ON button of the remote control handset 8 to switch on the light.
  Press the OFF button of the remote control handset 8 to switch off the light.

Switching the light on / off using the wall switch:

• The wall switch is in the normal position (OFF).
  ☐ Switch the light off by pressing the wall switch several times (2–3 switching cycles). The light can then be switched off via the wall switch or the remote control 8.

Trouble shooting: Should the remote control 8 not react after the light has been switched on, first press the wall switch in order to switch the light off. Then wait for around 15-20 seconds and repeat point 2 in the section called "Switching the light on / off using the wall switch". If the remote control 8 still doesn't respond after repeated switching on the light, please check the battery inside the remote control 8.

- Replacing a bulb

CAUTION! RISK OF ELECTRIC SHOCK!

When changing the bulbs, first disconnect the light from the mains supply. Remove its fuse or switch off the automatic cutout in the fuse box (0 position).

⚠️ CAUTION! RISK OF BURNS! Allow the light to cool completely.

Replace the bulb only after it has fully cooled.
Rotate the defective bulb carefully anticlockwise out of the fitting 9.

☐ Use a clean, fluff-free cloth when you are replacing a bulb.
☐ Onlyuse 220-240V \~ LED lamps with a maximum output of 3 Watt and E14 base.
☐ Rotate the new bulb clockwise into the fitting. Check that the bulb is correctly seated.
☐ Replace the fuse or switch on the circuit breaker (Position I) inside the fuse box.

● Maintenance and cleaning

CAUTION! RISK OF ELECTRIC SHOCK!

Before cleaning the lamp make sure that it is isolated from the mains supply. Remove its fuse or switch off the automatic cutout in the fuse box (0 position).

CAUTION! RISK OF ELECTRIC SHOCK!

For electrical safety reasons, never clean the light with water or other fluids or immerse it in water.

⚠️ CAUTION! RISK OF BURNS! Allow the light to cool completely.

Do not use any solvents, petrol or similar. This would cause damage to the light.
☐ Use a dry, fluff-free cloth for cleaning.
☐ Replace the fuse or switch on the circuit breaker (Position I) inside the fuse box.

- Disposal

The packaging and ancillary packing consist entirely of environmentally-friendly materials. They can be disposed of at your local recycling facility.

The symbol of the wheelie bin with the line through it means that, in the European Union, the product has to be disposed

of in a separate refuse collection. This applies to the product and to all components bearing this symbol. Products marked in this way may not be disposed of along with normal domestic waste but have to be handed in at a recycling collection point for electrical and electronic appliances. Recycling helps to reduce the consumption of raw materials and to ease the burden on the environment.

Disposal/Guarantee and service

Batteries must not be disposed of as household refuse! Advice is available from your local council. Return the batteries and / or the device through the appropriate collection facilities.

● Guarantee and service

●Guaranteed declaration

This product has a 3-year guarantee from the date of purchase; the guarantee is only valid for the original purchaser and is not transferable. Keep your receipt as proof of purchase. The guarantee applies to material or manufacturing defects only. It does not cover wear parts or damage caused by improper use. The guarantee is void in cases of unauthorised tampering. This guarantee does not limit your legal rights. Contact the service centre by telephone if there is a guarantee case. This is the only way to ensure that your device can be sent in free of charge.

Serviceaddress

When inquiring about your product, have your receipt and product number (e.g. IAN 12345) ready as your proof of purchase.

- Declaration of conformity CE

This product fulfils the requirements of the applicable European and national directives (Electromagnetic Compatibility 2004/108/EC, Low Voltage Directive 2006/95/EC, Ecodesign Directive 2009/125/EC, RoHS Directive 2011/65/EU,

R&TTE Directive 1999/5/EG). Conformity has been demonstrated. The relevant declarations and documents are held by the manufacturer.

Manufacturer

59929 Brilon (Germany)

Last Information Update · Tietojen tila · Informationsstatus

Stand van de informatie · Stand der Informationen:

05/2015·Ident.-No.: 14104202L052015-GB/FI/NL