PRX 130 - Car hands-free kit ETON - Free user manual and instructions

Product Type	Car Hands-Free Kit
Brand	Eton
Model	PRX 130
Dimensions (approx)	100 x 60 x 20 mm
Weight (approx)	100 g
Power Supply	12V car charger via cigarette lighter socket
Bluetooth Version	4.0
Wireless Range	Up to 10 meters
Battery Type	Built-in rechargeable lithium-ion
Talk Time (approx)	10 hours
Standby Time (approx)	200 hours
Main Functions	Bluetooth hands-free calling, music streaming, noise cancellation, voice assistant support
Speaker Type	Full-range dynamic speaker
Microphone	Built-in omnidirectional
Controls	Multi-function button, volume up/down
Mounting Method	Sun visor clip or dashboard adhesive pad
Indicators	LED for pairing, power, battery
Maintenance	Wipe with a soft, dry cloth. Do not use liquids.
Safety	Do not disassemble. Keep away from moisture. Use only provided charger.
Spare Parts / Repairability	No user-serviceable parts. Contact manufacturer for repairs.
Compatibility	Most Bluetooth-enabled smartphones

Frequently Asked Questions - PRX 130 ETON

How do I pair the PRX 130 with my phone?

Turn on the device by pressing the multi-function button until the LED flashes red and blue. On your phone, enable Bluetooth and select 'Eton PRX 130' from the list. If prompted, enter PIN 0000.

Can I charge the device while using it?

Yes, you can charge the PRX 130 via the included car charger and still use it for calls or music.

How do I adjust the volume?

Press the '+' or '-' buttons on the device to increase or decrease volume during a call or music playback.

Why is the device not turning on?

Ensure the device is charged. Connect to a power source for at least 30 minutes. If still no response, try resetting by pressing the multi-function button for 10 seconds.

Can I answer calls with voice commands?

Yes, press the multi-function button once to activate your phone's voice assistant (Siri, Google Assistant) for hands-free operation.

How do I clear the paired devices list?

With the device off, press and hold the multi-function button for 8 seconds until the LED flashes red rapidly. This will erase all paired devices.

Can I connect two phones at the same time?

No, the PRX 130 supports only one active Bluetooth connection at a time. You must disconnect one before pairing another.

What is the best mounting position?

Clip the device onto the sun visor or use the adhesive pad on the dashboard, ensuring it is within easy reach and does not obstruct driving.

How long does it take to fully charge?

Charging time is approximately 2 hours using the included car charger.

Why is audio quality poor during calls?

Check that the device is not obstructed and move it closer to you. Reduce background noise and ensure the microphone is not covered. If issue persists, try re-pairing.

USER MANUAL PRX 130 ETON

Please read all warnings found in this manual. This information is highlighted in frames and is included to inform you of the potential danger of personal injury or damage to property.

Hearing Damage

Continuous, excessive exposure to sound pressure levels in excess of 85 dB can cause a loss of hearing. ETON components are capable of producing sound pressure levels greater than 85 dB.

Volume and Driver Awareness

Use of sound components can impair your ability to hear necessary traffic sounds and may constitute a hazard while driving your automobile.

ETON accepts no liability for hearing loss, bodily injury or property damage as a result of use or misuse of this product.

MONTAGE

Do not use your automobile until all components of the loudspeaker system have been secured to the interior framework. Failure to do so may turn a component into a dangerous, flying projectile during a sudden stop or accident.

Do not drill or drive screws through any vehicle interior or carpeted floor before inspecting the underside for potential punctures to control lines or cables. Be sure to avoid all fuel lines, brake lines, electrical cables or oil lines when planning the installation.

Before beginning installation of the loudspeaker system remove the minus connector from the automobile battery in order to avoid possible short circuits.

Choosing a Location

For ease of installation use original factory speaker locations. Using these positions will save considerable installation time and provide the best optical integration. Avoid installing speakers behind thick stock fabric or cloth. This could - especially in the case of tweeters - restrict output and reduce sound volume.

Installation of Mid/Woofer

If it is not possible to install the loudspeaker in the original factory speaker location, the most used position is the door panel.

1. After choosing a location, carefully remove the trim panels. Be sure that sufficient mounting depth is available and that no moveable mechanical parts (window, window regulator handle) are restricted in their functionality.

Caution: Use care when removing interior trim panels. Car manufacturers use a variety of fastening devices that can be damaged in the disassembly process.

1. Use the enclosed drilling template to cut a suitable hole in the trim panel and, if necessary, in the sheet metal behind. Drill holes for the fastening screws. Mount the parts as shown in figure 1.

Attention: If sheet metal must be cut or removed contact your authorized car dealer for professional advice. By damage to supporting body structures the safety certificate may be withdrawn.

1. If you plan to use grilles or panels in front of the loudspeaker, ensure that sufficient space is available for the path of the loudspeaker cone. Should the distance not be sufficient, the cone could beat against the grille or panel thus damaging the loudspeaker.

Fastening of the Passive Crossover (only CEX 650)

1. Remove the cover as shown in figure 2.

2. Drill two holes for the fastening screws using the uncovered crossover. Secure the crossover with two screws and replace the cover.

Important: Mount the crossover in a location that will provide easy access for later connection and system tuning.

ELECTRICAL INSTALLATION

Whenever you run wires through sheet metal, use tape or grommets to properly insulate the metal edges from cable jackets. This technique prevents chafing and possible short circuits that could damage an amplifier or the loudspeakers.

1. Follow the wiring diagrams figures 3, 4, 5 to connect the loudspeaker system to your automobile radio and possibly to an amplifier. Be very careful of correct polarity of all connections.

The tweeters should only be installed through a crossover.

1. Replace the automobile battery connector and test the loudspeaker system.

Tuning of the Passive Crossover (only CEX 650)

Dependant upon your installation every crossover can be tuned to three reproduction adjustments. To achieve this adjustment connect the + pole for the tweeter to one of the three positions.

Caution: Do not apply power to the tweeters without first installing crossovers.

Ensure that all audio equipment is turned off before tuning the crossover.