Base1 - Headphones Lamax - Free user manual and instructions

Product Type	Over-Ear Wireless Headphones
Brand	Lamax
Model	Base1
Dimensions (W x H x D)	Approx. 18 x 16 x 7 cm
Weight	Approx. 150 g
Power Source	Rechargeable Lithium-Ion Battery
Battery Life	Up to 10 hours (typical)
Charging Time	Approx. 2 hours via USB-C
Connectivity	Bluetooth 5.0
Wireless Range	Up to 10 meters (33 feet)
Controls	On-ear buttons: volume, playback, power
Built-in Microphone	Yes, for hands-free calling
Impedance	32 Ω
Frequency Response	20 Hz – 20 kHz
Driver Diameter	40 mm
Compatibility	Smartphones, tablets, PCs with Bluetooth
Included Accessories	USB-C charging cable, audio cable (3.5mm)
Care Instructions	Wipe with dry cloth; avoid moisture
Safety Notes	Do not use at high volumes for extended periods
Repairability	Battery replaceable by service center

Frequently Asked Questions - Base1 Lamax

How do I pair the headphones with my phone?

Turn on the headphones using the power button (hold 3 seconds). The indicator light will flash blue and red. On your phone, enable Bluetooth and select 'Lamax Base1' from the available devices.

How do I charge the headphones?

Use the included USB-C cable to connect the headphones to a USB power source (like a computer or charger). The LED indicator will show red during charging and turn off when fully charged. Charging typically takes about 2 hours.

Can I use the headphones while they are charging?

Yes, you can continue listening while charging via the auxiliary audio cable (3.5mm), but wireless playback is disabled during charging.

How do I adjust the volume?

Use the volume up/down buttons on the ear cup. Press briefly to adjust volume step by step. A beep indicates maximum/minimum volume.

Why is the sound only coming from one ear?

First, check that the audio source is in stereo mode. Then, ensure the headphone plug (if using wired) is fully inserted. If the issue persists, clean the audio jack with a dry cloth.

How do I reset the headphones?

Turn off the headphones, then press and hold the power button for 10 seconds until the LED flashes red/blue rapidly. Release to reset. This clears paired devices; you'll need to pair again.

Are the headphones waterproof?

No, the Lamax Base1 is not waterproof. Avoid exposure to rain, sweat, or moisture. Clean only with a dry cloth to prevent damage.

What is the battery life?

On a full charge, you can enjoy up to 10 hours of playback at moderate volume. Battery life may vary with volume and usage.

Can I use the microphone on a PC?

Yes, the built-in microphone works for voice calls on PCs via Bluetooth. For wired use, ensure your PC has a combined audio/mic port or use a splitter.

What should I do if the headphones don't turn on?

Charge the headphones for at least 30 minutes. If still not working, try a different USB cable and charger. If unsuccessful, reset the headphones (see FAQ 6). If the problem persists, contact Lamax support.

USER MANUAL Base1 Lamax

Diagram of a mechanical component with numbered parts, likely for assembly or labeling.

1. Volume Up / Next Track

2. Volume Down / Previous Track

3. Answer / End / Reject call

4. On / Off, Play /

5. Bluetooth LED

6. AUX input, 3

7. Microphones

8. Microphone

9. MicroUSB so

10. MICRODSB SOCKET

Power

To turn on the headphones, press and hold d_1/d_2 . A blue and red LED will briefly light up, indicating that the headphones are turned on.

Switch off

To turn off the headphones, press and hold 📁. A red LED will briefly light up, indicating that the headphones are turned off.

Pairing

1. Pairing with a new device

a) On your device, activate Bluetooth and put it in Bluetooth search mode.

b) Select „LAMAX Base1" from the list of devices found. If a pairing code is required, enter .0000" and confirm.

c) Successful pairing of the headphones with the device is indicated by an audible tone and a blue LED lighting up.

d) Playback can be operated either by a paired device or by using the controls on the headphones.

2. Repeated pairing

To pair with a device that has already been used, turn on the headphones by holding down the button 📁/√. The headphones will automatically connect to the device. A successful connection is indicated by a tone and a blue LED lighting up.

1. Pairing with a second device

To pair with a different device:

a) Using your mobile, first disconnect the current paired device. The headphones will automatically switch to pairing mode.

b) Then, continue as described in point 1 of the manual „Pairing with a New Device“.

Playback / Controls

1. Press ☐ to start your music. Pressing the button again will pause the track you are playing.

2. Volume up (press), next track (hold)

3. Decrease volume (press), previous track (hold)

Note: When the headphones are charging, playback is deactivated.

Hands-free

1. To answer an incoming call, briefly press

2. To end the call, briefly press the same button again

3. To reject a call, press and hold 📄 for approximately 2 seconds.

4. To increase or decrease the volume during a call, press these keys.

- Press the ⚫️ key to increase the volume.

- Press the ⚡ key to decrease the volume.

Using the headphones in „Line-in“ mode

You may use the headphones with a cable in order to conserve battery life. Connect one end of a 3.5 mm audio cable into the socket at the base of the earpiece of your headphones and connect the other end to your audio device. Wireless operations do not function if an audio cable is being used.

MicroSD

Thanks to the microSD card slot, you can play music directly from the card. The headphones must be on and charged to allow playback to start.

1. Insert the microSD card into the slot located on the right earcup.

2. An audio signal sounds as it switches to playback mode and then it begins playback.

3. The playlist is played back sequentially from the card.

Charging

The headphones can be charged using the supplied USB cable by connecting to a suitable USB device – an adapter, PC, or power bank. Do not charge the headphones with a higher input voltage than SV as they may be damaged. Keep the device under supervision while charging.

The red LED indicates that the headphones are connected to a power source and switches off when fully charged.

Technical Specifications

Battery:	Li-Ion, 500 mAh
Charging input:	5 V / 1.0 A
Standby time:	about 200 hours
Playback time:	up to 20 hours
Charging time:	2-3 hours(*according to charging current)
Bluetooth range:	≥10 m
Bluetooth Version:	vS

Driver unit Specifications

Diameter:	40 mm
Impedance:	32
Frequency Response:	20 Hz – 20 000 Hz

The current version of the user manual is available for download

her

https://beat.lamax-electronics.com/base1/manuals

LAMAX

BASE1

Diagram of a mechanical component with numbered parts and highlighted features

https://beat.lamax-electronics.com/base1/manuals

CE RoHS

LAMAX

BASE1

Diagram of a mechanical component with numbered parts and highlighted features

https://beat.lamax-electronics.com/base1/manuals

CE RoHS

LAMAX

BASE1

Diagram of a mechanical component with numbered parts labeled 1 through 8, showing internal structure and features.

https://beat.lamax-electronics.com/base1/manuals

CE RoHS

LAMAX

BASE1

Diagram of a mechanical component with numbered parts and highlighted features

https://beat.lamax-electronics.com/base1/manuals

LAMAX

BASE1

Diagram of a mechanical component with numbered parts and highlighted features

https://beat.lamax-electronics.com/base1/manuals

LAMAX

BASE1

Diagram of a mechanical component with numbered parts labeled 1 through 8, showing internal structure and alignment markers.

The Ground Truth image displays a single, solid horizontal line. According to Rule 2 (UNDERSCORE & LINE RULES), this is a stylistic or background line, not a placeholder underscore. Therefore, the OCR result must ignore it and output nothing or only meaningful text. The provided OCR content is "____", which consists of four underscores. This is an incorrect interpretation of the line as a fill-in-the-blank placeholder, violating the rule that stylistic lines must be ignored. The OCR has hallucinated underscores where none should exist in the GT, violating the rule to ignore such lines. Hence, the OCR result is inconsistent with the Ground Truth.

https://beat.lamax-electronics.com/base1/manuals

LAMAX

BASE1

HR - Priručnik za korisnika

Diagram of a mechanical component with numbered parts, likely a valve or connector assembly