YT-818231 - Lamp Yato - Free user manual and instructions

USER MANUAL YT-818231 Yato

N 6 4 L 7 III

PL

1. lamp shade
2. bracket screw
3. mounting bracket
4. connection cable
5. motion detector
6. blue
7. brown

DE

Read the operating instruction

Attention! Risk of electric shock

PRODUCT CHARACTERISTICS

The spotlight is designed to illuminate small open spaces: building façades, monuments, advertisements, etc. The light source consists of white LEDs, which means low power consumption and low power loss due to heating of the spotlight. The spotlight housing is made of metal. The light source is protected by tempered glass with a gasket embedded in the frame. The lamp is mounted by means of a bracket which allows the luminaire to be set vertically at an appropriate angle.

SAFETY INSTRUCTIONS

A qualifi ed electrician is required to install the spotlight.

Before starting the installation, switch off the power supply to the mains to which the spotlight is to be connected! Failure to do so may lead to electric shock, resulting in serious injury or even death.

The luminaire has a non-replaceable glass and in case of damage or breakage of the protective glass, the entire spotlight should be replaced immediately. The luminaire must not be used without the protective glass or with damaged protective glass!

The electrical wiring system powering the lamp should be efficient, periodically checked, with properly selected fuses and should provide protection against electric shock through quick shutdown.

Never use a lamp with visible mechanical damage, damage to the power cable insulation, broken spotlight glass, or other visible damage. Damaged power supply cable cannot be repaired and must be replaced in their entirety by a qualified specialist. All adjustment and mounting operations must be carried out with the lamp power supply disconnected.

Do not touch the spotlight housing, as it becomes hot during operation and may cause burns. To reduce the risk of strangulation, flexible wiring connected to this luminaire shall be effectively fixed to the wall if the wiring are within arm's reach.

SPOTLIGHT OPERATION

Spotlight without a motion sensor

Fix the spotlight to the wall or other fixed element with screws or bolts through the openings in the mounting bracket, so that the bracket is firmly and securely fastened to the surface. Make sure that the lamp is mounted according to the instructions in Figure (II).

By tightening the bracket screws you can set the lamp in one specific position.

Illuminating component installation and replacement

It is not possible to replace the illuminating component. In case of its damage the whole spotlight should be replaced with a new one.

EN

Connecting the power supply

A qualifi ed electrician is required to connect the lamp power supply.

Before starting the installation, switch off the power supply to the mains to which the lamp is to be connected! Failure to do so may lead to electric shock, resulting in serious injury or even death. It is recommended that the lamp power supply network be protected by a residual current device (RCD) with a tripping current of no more than 30 mA.

The lamp is equipped with a short-length cable allowing to connect it to the power supply with the parameters given in the table and on the rating label.

Connect the lamp so that the degree of protection of the connection point is equal to or greater than the degree of protection of the lamp indicated in the table and on the rating label.

The wires of the cable should be connected in accordance with the insulation colour scheme (III). Contact an authorised service centre if you need to replace the cable which is connected to the lamp.

Caution! Do not replace the cable which is connected to the lamp by yourself. The cable is connected in a box ensuring an adequate level of protection. If the box is unsealed, moisture may enter the box, which may cause damage to the lamp and/or mains power supply, and electrical shock, resulting in injury or death. The manufacturer does not take responsibility for damage resulting from the users replacing the cable connected to the lamp on their own.

MAINTENANCE

Warning! Before starting maintenance, disconnect the lamp from the power supply.

Clean the luminaire and the glass with a soft, damp cloth. Do not use pressure washers, cleaning agents containing abrasive or corrosive substances, solvents or alcohol for maintenance.

EN

TECHNICAL DATA

Parameter Measurement unit Value
Catalogue No. YT-818221 YT-818231
Rated voltage [V~] 230
Rated frequency [Hz] 50/60
Electric insulation class I
Protection rating IP65
Rated power [W] 10 20
Number of LEDs 15 30
LED life [h]	30,000 ± 10%
Luminous flux	[lm]	950	1900
Colour rendering index CRI Ra		≥80
Colour temperature	[K] 6500
Power factor		0,5
Power supply cable type H05RN-F	3 x 1 mm	2
Minimum mounting height	[m]	3,0
Filter	[mm]	115x98x32	140x124,5x32
Weight	[kg]	0.2	0.3

This symbol indicates that waste electrical and electronic equipment (including batteries and storage cells) cannot be disposed of with other types of waste. Waste equipment should be collected and handed over separately to a collection point for recycling and recovery, in order to reduce the amount of waste and the use of natural resources. Uncontrolled release of hazardous

components contained in electrical and electronic equipment may pose a risk to human health and have adverse effects for the environment. The household plays an important role in contributing to reuse and recovery, including recycling of waste equipment. For more information about the appropriate recycling methods, contact your local authority or retailer.

DE

PRODUKTBESCHREIBUNG

CARACTÉRISTIQUES DU PRODUIT