YT-818251 - Lamp Yato - Free user manual and instructions
Find the device manual for free YT-818251 Yato in PDF.
| Product type | LED floodlight with motion sensor |
| Brand | Yato |
| Model | YT-818251 |
| Power supply | 230 V~, 50/60 Hz |
| Rated power | 50 W |
| Number of LEDs | 75 |
| Luminous flux | 4750 lm |
| Color temperature | 6500 K (daylight) |
| Color Rendering Index (CRI) | ≥ 80 Ra |
| Sensor detection angle | 120° |
| Sensor range | 10 m ± 2 m |
| Adjustable shutdown delay | 10 s to 300 s |
| Recommended mounting height | 3 m |
| Electrical insulation class | Class I |
| Protection rating (IP) | IP65 (dust-tight and protected against water jets) |
| LED lifetime | 30 000 h ± 10% |
| Power cable type | H05RN-F 3×1 mm² |
| Dimensions (W × H × D) | 232 × 207.5 × 32 mm |
| Weight | 0.9 kg |
| Body material | Metal with tempered glass lens |
| Sensor adjustment | Sensitivity (SENS), time delay (TIME), day/night threshold (LUX) |
| Main functions | Outdoor lighting with motion detection, adjustable sensitivity and lighting duration |
| Maintenance and cleaning | Clean with a soft, damp cloth, without abrasive products or solvents |
| Safety | Installation by a qualified electrician, cut off power before maintenance, replace the floodlight if the glass is damaged |
| Spare parts and repairability | LEDs not replaceable, complete floodlight must be replaced in case of failure; cable not replaceable by user |
Frequently Asked Questions - YT-818251 Yato
User questions about YT-818251 Yato
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Lamp in PDF format for free! Find your manual YT-818251 - Yato and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. YT-818251 by Yato.
USER MANUAL YT-818251 Yato
Read the operating instruction
Attention! Risk of electric shock
- lamp shade
- bracket screw
- mounting bracket
- connection cable
- motion detector
- blue
- brown
DE
PRODUCT CHARACTERISTICS
The spotlight is designed to illuminate small open spaces: building façades, monuments, advertisements, etc. The light source consists of white LEDs, which means low power consumption and low power loss due to heating of the spotlight. The spotlight housing is made of metal. The light source is protected by tempered glass with a gasket embedded in the frame. The lamp is mounted by means of a bracket which allows the luminaire to be set vertically at an appropriate angle.
SAFETY INSTRUCTIONS
A qualifi ed electrician is required to install the spotlight.
Before starting the installation, switch off the power supply to the mains to which the spotlight is to be connected! Failure to do so may lead to electric shock, resulting in serious injury or even death.
The luminaire has a non-replaceable glass and in case of damage or breakage of the protective glass, the entire spotlight should be replaced immediately. The luminaire must not be used without the protective glass or with damaged protective glass!
The electrical wiring system powering the lamp should be efficient, periodically checked, with properly selected fuses and should provide protection against electric shock through quick shutdown.
Never use a lamp with visible mechanical damage, damage to the power cable insulation, broken spotlight glass, or other visible damage. Damaged power supply cable cannot be repaired and must be replaced in their entirety by a qualified specialist. All adjustment and mounting operations must be carried out with the lamp power supply disconnected.
Do not touch the spotlight housing, as it becomes hot during operation and may cause burns. To reduce the risk of strangulation, flexible wiring connected to this luminaire shall be effectively fixed to the wall if the wiring are within arm's reach.
SPOTLIGHT OPERATION
Spotlight without a motion sensor
Fix the spotlight to the wall or other fixed element with screws or bolts through the openings in the mounting bracket, so that the bracket is firmly and securely fastened to the surface. Make sure that the lamp is mounted according to the instructions in Figure (II).
By tightening the bracket screws you can set the lamp in one specific position.
Spotlight with a motion sensor
The installation should be carried out as for a spotlight without a motion sensor, but the motion sensor's operating principle shall be taken into account when selecting the installation location. The sensor is designed so that it works best when mounted at a height of approximately 3 metres from the ground. Avoid placing the sensor near trees or bushes which may cause the device to switch on in windy weather. Avoid directing or placing the device near heat sources, as this may cause its undesired operation. Avoid directing the sensor towards bright light, as the device will not operate at the minimum (minus sign) setting of the knob marked "LUX". Avoid mounting in locations with strong electromagnetic interference, as this may cause undesired switching on of the device. The sensor is the most sensitive to motion across the detection area, unlike motion towards or away from the sensor. Therefore, the sensor must be positioned so that the movement is transverse to the sensor axis.
EN
Illuminating component installation and replacement
It is not possible to replace the illuminating component. In case of its damage the whole spotlight should be replaced with a new one.
Connecting the power supply
A qualifi ed electrician is required to connect the lamp power supply.
Before starting the installation, switch off the power supply to the mains to which the lamp is to be connected! Failure to do so may lead to electric shock, resulting in serious injury or even death.
It is recommended that the lamp power supply network be protected by a residual current device (RCD) with a tripping current of no more than 30 mA.
The lamp is equipped with a short-length cable allowing to connect it to the power supply with the parameters given in the table and on the rating label.
Connect the lamp so that the degree of protection of the connection point is equal to or greater than the degree of protection of the lamp indicated in the table and on the rating label.
The wires of the cable should be connected in accordance with the insulation colour scheme (III).
Contact an authorised service centre if you need to replace the cable which is connected to the lamp.
Caution! Do not replace the cable which is connected to the lamp by yourself. The cable is connected in a box ensuring an adequate level of protection. If the box is unsealed, moisture may enter the box, which may cause damage to the lamp and/or mains power supply, and electrical shock, resulting in injury or death. The manufacturer does not take responsibility for damage resulting from the users replacing the cable connected to the lamp on their own.
Motion sensor adjustment
Sensitivity is the maximum distance from which a sensor can be switched on. Turning the "SENS" knob clockwise increases sensitivity while turning it counter-clockwise decreases sensitivity.
The length of time for which the device remains switched on after switching on can be adjusted within the range specified in the table. Turning the “TIME” knob counter-clockwise reduces the time period while turning the knob clockwise increases it. Turning the knob in the direction of the “+” symbol increases the time period while turning the knob in the direction of the “-” symbol decreases it.
Caution! When the light is switched on by the sensor, any subsequent motion detection will cause the time count to start anew.
The light level control module has a built-in sensor device (photocell) which detects light and darkness. It is possible to set the operation of the sensor by means of the knob marked "LUX". The "+" symbol indicates that the load will be switched on by the sensor both during the day and night. The "-" symbol indicates that the load will only be switched on at night.
CAUTION! It is normal for the load switching to be delayed in relation to the power-on time.
| Motion sensor parameter Unit Value | ||
| Mounting height [m] 3 | ||
| Detection angle [ | 9 120 | |
| Detection range [m] 10 ± 2 | ||
| Delay time [s] | 10 ± 5 ÷ 300 ± 60 |
MAINTENANCE
Warning! Before starting maintenance, disconnect the lamp from the power supply. Clean the luminaire and the glass with a soft, damp cloth. Do not use pressure washers, cleaning agents containing abrasive or corrosive substances, solvents or alcohol for maintenance.
TECHNICAL DATA
| Parameter | Measurement unit | Value | |||||
| Catalogue No. | YT-818241 | YT-818251 | YT-818261 | YT-818271 | YT-818281 | YT-818291 | |
| Rated voltage [V~] 230 | |||||||
| Rated frequency [Hz] 50/60 | |||||||
| Electric insulation class I | |||||||
| Protection rating IP65 IP65 IP54 IP54 IP54 IP54 | |||||||
| Rated power [W] 30 50 10 20 30 50 | |||||||
| Number of LEDs 45 75 15 30 45 75 | |||||||
| LED life [h] 30,000 ± 10% | |||||||
| Luminous flux | [lm] | 2850 | 4750 | 950 | 1900 | 2850 | 4750 |
| Colour rendering index CRI Ra | ≥80 | ||||||
| Colour temperature | [K] 6500 | ||||||
| Power factor | 0,9 | 0,9 | 0,5 | 0,5 | 0,9 | 0,9 | |
| Power supply cable type | H05RN-F 3 x 1 mm2 | ||||||
| Minimum mounting height | [m] | 3,0 | |||||
| Dimensions | [mm] | 181x169,5 x32 | 232x207,5 x32 | 115x155,5 x37 | 140x173,5 x37 | 181x209,5 x37 | 232x248.5 x37 |
| Weight | [kg] | 0.6 | 0.9 | 0.27 | 0.37 | 0.64 | 1 |
