YSFLQ35*25*25 - Grease trap Vevor - Free user manual and instructions

Product Type	Grease Trap
Brand	Vevor
Model	YSFLQ35*25*25
Dimensions (L×W×H)	350 × 250 × 250 mm
Water intake mode	Side entry
Material	Stainless steel (estimated)
Included parts	Drain pipe, pipe gasket, male adapter, rubber pad, nut, sealing gasket, valve switch, sealing tape
Installation	On a flat, hard, and smooth surface
Intended use	Separation of grease and oil from wastewater
Safety instructions	Do not sit or stand on the device; inspect before each use; do not exceed capacities
Maintenance	Regular cleaning of the filter and draining of grease
Warranty	Technical support and electronic warranty certificate at www.vevor.com/support

Frequently Asked Questions - YSFLQ35*25*25 Vevor

How to install the Vevor YSFLQ35*25*25 grease trap?

Place the device on a flat and hard surface. Install the drain pipe gasket at the separator outlet. Secure the rubber pad with the gasket and nut. Wrap the sealing tape around the male adapter and mount the valve switch. Connect the water inlet pipe to the middle of the filter.

What are the dimensions of the YSFLQ35*25*25?

The dimensions are 350 mm in length, 250 mm in width, and 250 mm in height.

Does the grease trap require electrical power?

No, this model is fully mechanical and does not require any electrical power.

How to clean the grease trap?

Regularly remove accumulated grease from the tray. Clean the filter with warm water and a mild detergent. Inspect the gaskets and replace them if necessary.

What is the maximum flow rate of the grease trap?

The flow rate is not specified in the manual, but for a model of this size, it is suitable for standard domestic kitchen sinks.

Is the product suitable for outdoor use?

The product is designed for indoor use on a flat surface. Exposure to weather could damage it.

What materials make up the grease trap?

The manual does not specify the material, but it is likely stainless steel or resistant plastic. Contact the manufacturer for confirmation.

How to know when to empty the grease trap?

Visually check the grease level in the tray. It is recommended to empty it when the grease layer reaches about 80% of the separator height.

Can I use the grease trap with a garbage disposal?

Use with a garbage disposal is not recommended, as solid particles can clog the filter. Filter large waste before entry.

Where to find replacement parts?

Contact Vevor customer service via www.vevor.com/support to obtain replacement parts such as gaskets or switches.

USER MANUAL YSFLQ35*25*25 Vevor

Technical Support and E-Warranty Certificate www.vevor.com/support

GREASE TRAP

USER MANUAL

YSFLQ35*25*25

YSFLQ60*40*40

YSFLQ37*26*26

YSFLQ63*31*32

YSFLQ60*40*39

We continue to be committed to provide you tools with competitive price. "Save Half", "Half Price" or any other similar expressions used by us only represent of savings you might benefit from buying certain tools with us compared top brands and does not necessarily mean to cover all categories of tools offered are kindly reminded to verify carefully when you are placing an order with us actually saving half in comparison with the top major brands.

VEVOR®

TOUGH TOOLS, HALF PRICE

GREASE TRAP

YSFLQ35*25*25

YSFLQ60*40*40

YSFLQ37*26*26

YSFLQ63*31*32 YSFLQ60*40*39

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us:

Technical Support and E-Warranty Certificate www.vevor.com/support

This is the original instruction. Please read all manual instructions carefully before operating. VEVOR reserves the right to interpret the user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you of any technology or software updates on our product.

WARNING:

Read this material before using this product. Failure to do so can result in serious injury.

Assembly precautions

1. Assemble only according to these instructions. Improper assembly can create hazards.
2. Wear safety goggles and duty work gloves during assembly.
3. Keep the assembly area clean and well-lit.
4. Keep bystanders out of the area during assembly.
5. Do not assemble when tired or when under the influence of alcohol, drugs, or medication.
6. The product capabilities apply to properly and completely assembled products only.
7. Assemble on a flat, level, hard, and smooth surface capable of safely supporting the GREASE TRAP.
8. For additional information regarding the parts listed in the following pages, please refer to the Assembly Diagram of this manual. Unwrap and separate all parts in a clean work area.

Use precautions

1. DO NOT SIT OR STAND ON THIS ITEM.
2. This product is not a toy. Do not allow children to play with or item.
3. Do not exceed capacities.
4. Use only on a flat, level, hard and smooth surface capable of supporting a fully loaded GREASE TRAP.
5. Use as intended only.
6. Inspect before every use; do not use if parts are loose or damaged.

SAVE THIS MANUAL

PRODUCT PARAMETER

Model	Water Intake Mode	Product Size
YSFLQ35*25*25	Side Entrance	350*250*250mm
YSFLQ60*40*40	Side Entrance	600*400*400mm
YSFLQ37*26*26	Top Entrance	350*250*250mm
YSFLQ63*31*32	Top Entrance	630*310*320mm
YSFLQ60*40*39	Top Entrance	600*400*390mm

PARTS LIST

Name\MODEL	YSFLQ35*25*25YSFLQ37*26*26	YSFLQ60*40*40YSFLQ63*31*32YSFLQ60*40*39
	Qty	Qty
Drain Pipe	1	1
Drain Pipe Gasket	1	1
Male Adapter	1	2
Rubber Pad	1	2
Nut	1	2
Gasket	1	2
Valve Switch	1	2
Seal Tape	1	1

INSTRUCTIONS

STEP1

Place the product and parts horizontally on the floor.

STEP2

Install the drain pipe gasket in place and install it at the outlet oil-water separator.

STEP 3

Install the rubber pad in place, secure it with the gasket and nut, wrap tape around the male adapter, and finally install the valve switch.

YSFLQ63*31*32

YSFLQ60*40*39

STEP 4

Insert the water inlet pipe into the water inlet.

Note: The water inlet pipe should be placed in the middle of the screen.

Address: Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi Shanghai

Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia

Imported to USA: Sanven Technology Ltd. Suite 250.

9166 Anaheim Place, Rancho Cucamonga, CA 91730

EC

REP

SHUNSHUN GmbH

Römeräcker 9 Z2021,76351

Unit 5 Albert Edward House, The

Pavilions Preston, United Kingdom

Made In China

VEVOR®

TOUGH TOOLS, HALF PRICE

Technical Support and E-Warranty Certificate www.vevor.com/support

VEVOR®

TOUGH TOOLS, HALF PRICE

YSFLQ60*40*40YSFLQ35*25*25

YSFLQ37*26*26 YSFLQ63*31*32

YSFLQ60*40*39

NEED HELP? CONTACT US!

STEP 2

STEP 3

Water inlet

Address: Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi Shanghai Imported to Australia:

SIHAO PTY LTD. 1 ROKEVA STREET EASTWOOD NSW 2122 Australia

9166 Anaheim Place, Rancho Cucamonga, CA 91730

REPRÉSENTANT

DE LA CE

SHUNSHUN GmbH

Römeräcker 9 Z2021, 76351

Linkenheim-Hochstetten, Germany

REPRÉSENTANT

DU ROYAUME-UNI

Pooledas Group Ltd

YSFLQ60*40*40 YSFLQ35*25*25

YSFLQ37*26*26 YSFLQ63*31*32

YSFLQ60*40*39

STEP

STEP 3

YSFLQ37*26*26 Model number: YSFLQ63*31*32

Dimensions

PHASE 2

STEP 3

In AUS: SIHAO PTY LTD. 1 ROKEVA STREET EASTWOOD NSW 2122 Australia

9166 Anaheim Place, Rancho Cucamonga, CA 91730

YSFLQ37*26*26 YSFLQ63*31*32

STEP 2

STEP 3

SIHAO PTY LTD. 1 ROKEVA STREET EASTWOOD NSW 2122 Australia

9166 Anaheim Place, Rancho Cucamonga, CA 91730

REPRESENTANTE CE

SHUNSHUN GmbH

Römeräcker 9 Z2021, 76351

Linkenheim-Hochstetten, Germany

YSFLQ60*40*40 YSFLQ35*25*25

YSFLQ37*26*26 YSFLQ63*31*32

YSFLQ60*40*39

NEED HELP? CONTACT US!

STEP 2

STEP 3

Water inlet

Address: Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi Shanghai. Imported to AUS:

SIHAO PTY LTD. 1 ROKEVA STREET EASTWOOD NSW 2122 Australia

Imported to USA: Sanven Technology Ltd. Suite 250.

9166 Anaheim Place, Rancho Cucamonga, California 91730

Przedstaw ciel UE

SHUNSHUN GmbH

Römeräcker 9 Z2021, 76351

YSFLQ60*40*40 YSFLQ35*25*25

YSFLQ37*26*26 YSFLQ63*31*32 YSFLQ60*40*39

NEED HELP? CONTACT US!

STEP 2

STEP 3

9166 Anaheim Place, Rancho Cucamonga, CA 91730

SHUNSHUN GmbH

Römeräcker 9 Z2021, 76351

YSFLQ60*40*40 YSFLQ35*25*25

YSFLQ37*26*26 YSFLQ63*31*32

YSFLQ60*40*39

NEED HELP? CONTACT US!

STEP 2

STEP 3

9166 Anaheim Place, Rancho Cucamonga, CA 91730

EC

REP

SHUNSHUN GmbH

Römeräcker 9 Z2021, 76351

Unit 5 Albert Edward House, The

Pavilions Preston, United Kingdom

Made in China

VEVOR®

TOUGH TOOLS, HALF PRICE