TM19 - Electric hedge trimmer Vevor - Free user manual and instructions

Product type	Manual leaf cutter
Model	TM19
Brand	Vevor
Package dimensions	540 x 540 x 240 mm
Net weight	5.98 kg
Gross weight	7.35 kg
Blade material	420 stainless steel (straight edge)
Container material	201 stainless steel
Size (inches)	19
Gear ratio	1:24
Load capacity	Approx. 40 g of dry matter
Operation mode	Manual (handle rotation)
Required turns	15 to 30 turns
Estimated cutting time	About 30 seconds per load
Safety	Sharp blade, use the lid, do not touch the grid during use
Maintenance	Clean after each use, store with blade guard
Warranty	1 year
Intended use	Cutting leaves for essential oil preparation or compost
Included accessories	Base, lid, handle, blade guard

Frequently Asked Questions - TM19 Vevor

How to use the Vevor TM19 leaf cutter?

Remove the top of the base, place about 40 g of uncut plants on the grid, replace the lid, then turn the handle clockwise for 15 to 30 turns. Then open to retrieve the cut leaves.

Is the Vevor TM19 electric?

No, it is fully manual. Turning the handle drives the blades through a 1:24 gear ratio.

What is the cutting capacity per load?

Approximately 40 grams of dry matter. For best results, do not overload the grid.

How long does it take to cut one load?

About 30 seconds of handle rotation is enough to cut one load.

What types of plants can I cut with this leaf cutter?

It is designed to cut leaves and tender plants, especially for essential oil preparation. Avoid thick branches or hard materials.

How to maintain the Vevor TM19?

Clean each part thoroughly after use. Store the device with the blade guard in place to protect the blade.

Is the blade of the TM19 sharp?

Yes, the 420 stainless steel blade is very sharp. Handle with care and never touch the grid during use.

Can I cut wet herbs?

It is recommended to use dry or slightly moist plants. Excess moisture may reduce cutting efficiency and clog the device.

Does the TM19 have a warranty?

Yes, Vevor offers a one-year warranty. For technical support, visit www.vevor.com/support.

What if the cut is not fine enough?

Repeat the process by turning the handle an additional 15 to 30 turns until the desired texture is achieved.

USER MANUAL TM19 Vevor

Technical Support and E-Warranty Certificate www.vevor.com/support

LEAF TRIMMER

MODEL: TM19

We continue to be committed to providing you with tools at competitive prices. "Save Half", "Half Price", or any other similar expressions used by us only represent the savings you might benefit from buying certain tools with us compared to top brands, and do not necessarily mean that all categories of tools offered are covered. We kindly remind you to verify carefully when placing an order with us that you are actually saving half in comparison with the top major brands.

VEVOR®

TOUGH TOOLS, HALF PRICE

POND AERATION

MODEL: TM19

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us:

Technical Support and E-Warranty Certificate www.vevor.com/support

This is the original instruction. Please read all manual instructions carefully before operating. VEVOR reserves the right to interpret the user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you of any technology or software updates on our product.

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

Read all safety warnings, instructions, illustrations, and specifications provided with this product. Failure to follow all instructions listed below may result in product damage or serious injury.

Basic Safety Information:

1. This product is for trimming leaves only.
2. The blade is very sharp; beware of injury when using the trimmer or replacing the blade.
3. Put on the blade sheath if you are not going to use it for a long time.
4. Make sure the lid is on before use.
5. Be gentle with the trimmer when using it. Violent use can result in accidental injury and damage to the trimmer.
6. Never place your fingers, gloves, or any other body part in contact with the grill or the blade.
7. Do not use scissors, knives, or any instrument above the grill.
8. This product is not a toy. Do not allow children to play with it.

Please Note:

The manufacturer does not accept any responsibility for damages caused to or by the trimmers resulting from inadequate use or assembly. Please use the trimmers in accordance with existing laws and regulations.

SAVE THESE INSTRUCTIONS

Basic parameters

Package size (mm)	540×540×240
Size (inch)	19
N.W (kg)	5.98
G.W (kg)	7.35
Operating mode	manual
Blade	420 Stainless steel/straight edge
Container	201 Stainless steel
Transmission ratio	1:24
Service life	1-year warranty

OPERATION

1. Remove the top from the flower trimmer's base.

Remove the top from the flower trimmer's base. The inside contains high-density rubber used to push the plant leaves into the blade grill. The cutting blades or wires are located below the grill.

1. Place the untrimmed plants on the grill.

Place the untrimmed plants on the grill. The plants should be enough to make sure the grill surface is covered (approximately 40 dry grams).

1. Place the top and handle back on the base.

1. Turn the handle clockwise for about 15-30 rounds.

Using the handle, make 15-30 complete turns. While spinning the handle, the inside rubber twist tongues multiply the rate of the spinning plants and blades by over 30

times. A combination of the rubber tongues pressing and rolling the plants and the spinning blades can improve the cutting efficiency. Only 30 seconds can yield one hour's work.

1. Remove the top and collect the plants.

Open the top and the trimmed plants and their fragmented bud/leaves can be found individually on the middle grill and in the trimmer basin. Depending on the type of plants, the trimming can be used for the preparation of plants' essential oils.

1. Repeat the process for more harvest.

If you think the leaf pieces are not small enough, keep repeating the above process as many times as you want, or until you have completed your harvest. When finished, easily clean every part of the trimmer and store it.

Sanven Technology Ltd.

Address: Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91

VEVOR®

TOUGH TOOLS, HALF PRICE

Technical Support and E-Warranty Certificate www.vevor.com/support

VEVOR®

TOUGH TOOLS, HALF PRICE

NEED HELP? CONTACT US!

Remove the top of the flower

NEED HELP? CONTACT US!

Address: Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

VEVOR®

TOUGH TOOLS, HALF PRICE

NEED HELP? CONTACT US!

NEED HELP? CONTACT US!