MD-808 - Motorcycle helmet Vevor - Free user manual and instructions

Product Type	Full-face motorcycle helmet
Brand	Vevor
Model	MD-808
Available sizes	S (55-56 cm), M (57 cm), L (58 cm), XL (59 cm)
Closure system	Micrometric buckle and D-rings
Approximate weight	Approximately 1500 g
Shell material	Polycarbonate
Inner lining	Removable and washable (recommended)
Maintenance and cleaning	Warm water and mild soap, dry at room temperature
Safety instructions	Read the manual before use; do not use after a severe impact
Warranty	Technical support and electronic warranty certificate at www.vevor.com/support
Intended use	Motorcycle riding only

Frequently Asked Questions - MD-808 Vevor

How to determine the correct helmet size?

Measure your head circumference with a measuring tape above the eyebrows. Choose the size corresponding to your measurement in the table: S (55-56 cm), M (57 cm), L (58 cm), XL (59 cm). Then perform the 'roll-off test': grasp the bottom edge of the helmet and pull upward and forward; if it dislodges easily, the size is not suitable.

How to properly fasten the chin strap of the Vevor MD-808 helmet?

Thread the end of the strap through both D-rings, then pass it over the first ring and through the second. Pull firmly so the helmet is well secured. For the micrometric buckle, insert the tab into the housing until it clicks. Ensure the chin strap is snug under the chin.

What to do if my helmet has suffered an impact or fall?

Never use a helmet that has suffered a severe impact, even if no visible damage appears. The impact absorption capacity is compromised. Replace it immediately with a new one or return it for inspection.

How to clean the helmet visor?

Use only warm demineralized water and mild soap. Never use alcohol, solvents, or glass cleaners. Remove the visor before cleaning the interior of the helmet and only reinstall it after complete evaporation.

Can I paint or modify my Vevor helmet?

No, never modify the helmet's characteristics. Do not scratch, cut, drill the shell, insert screws, or repaint. Any modification may compromise safety.

Where can I find technical support and warranty?

Visit the website www.vevor.com/support to obtain technical support and the electronic warranty certificate.

Is the helmet suitable for use other than motorcycle riding?

No, this helmet is designed exclusively for motorcycle riding. It does not guarantee the same level of safety for other uses (bicycle, sports, etc.).

How to maintain the helmet's inner lining?

The inner lining can be removed and hand washed with mild soap. Avoid harsh chemicals. Let it dry at room temperature, never near a heat source.

Can I attach my helmet to the motorcycle or leave it in the sun?

Never ride with the helmet attached to the motorcycle. Keep it away from heat sources (exhaust pipe) and direct sunlight, especially if the shell is dark colored. This could damage the paint or materials.

Is the helmet delivered with a complete user manual?

Yes, a user manual is provided. If you lost it, you can download it for free in PDF format on notice-facile.com or contact Vevor support.

USER MANUAL MD-808 Vevor

Technical Support and E-Warranty Certificate www.vevor.com/support

MOTORCYCLE HELMET

MODEL: MD-820A/MD-808/MD-202

We continue to be committed to provide you tools with competitive price. "Half", "Half Price" or any other similar expressions used by us only represent estimate of savings you might benefit from buying certain tools with us to the major top brands and does not necessarily mean to cover all car tools offered by us. You are kindly reminded to verify carefully when placing an order with us if you are actually saving half in comparison with major brands.

VEVOR®

MOTORCYCLE HELMET

Model: MD-820A/MD-808/MD-202

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us:

Technical Support and E-Warranty Certificate www.vevor.com/support

This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. Appearance of the product shall be subject to the product you receive. Please forgive us that we won't inform you again if there are any technology updates on our product.

PARAMETER LIST

Model	size	picture
MD-820A	L(59-60cm)
	M (57-58cm)
	S (55-56cm)
	XL (61cm)
MD-808	L(58cm)
	M (57cm)
	S (55-56cm)
	XL (59cm)
MD-202	L(59-60cm)
	M (57-58cm)
	S (55-56cm)
	XL (61cm)

OWNER'S MANUAL

The helmets are technologically advanced for the motorcycle rider's protection, which are made just for motorcycle riding only. They cannot guarantee the safety standard for different uses. In any accident, especially in the presence of strong impact, neither our helmets, nor any other helmet can eliminate the risk of serious or fatal injuries.

SAFETY WARNINGS

Please read this manual very carefully before wearing your helmet and keep it in a safe place for future reference. The instructions are very important for your safety. Avoid exposing your helmet to intense light sources. If your helmet is painted with one of the following fluorescent colors: yellow, red, orange, and green, please pay attention to the following instructions for detailed information.

1. READ THIS SECTION AND FOLLOW ITS INSTRUCTIONS SCRUPULOUSLY BEFORE USING YOUR NEW HELMET

The main function of a helmet is to protect your head in case of impact. This is accomplished by the shock absorbing capacities of various types of materials of different densities.

2. IF YOUR HELMET IS SUBJECTED TO AN IMPACT, DO NOT PUT IT ON.

Never use a helmet that has suffered an impact. Although visible damage may appear on the shell, the helmet accomplishes its shock absorbing functions through the alteration and/or partial destruction of its structure. In essence, a helmet is therefore unable to perform the functions for which it was designed after a severe impact. A helmet that has suffered a severe blow should be discarded and replaced or returned for competent inspection.

3. SIZING AND PROPER POSITIONING.

WARNING! SIZING is probably the single most important function you as a helmet owner must perform to allow your helmet to protect your head. SIZING should always be performed under the supervision of an authorized dealer. By the time you read this manual, it should have already been determined that your helmet is of the proper size for your head. If you did not put your helmet on with the guidance of an authorized dealer, WE STRONGLY RECOMMEND you immediately return to your local authorized dealer and ask him or her to help you determine if indeed your helmet fits your head. Should that be impossible for any reason, please read the following sizing instructions very carefully. Should you determine that your helmet is not of the proper size, please return to your authorized dealer and exchange your helmet for one that fits. Do not ride with a helmet that is either too small or too large for your head.

4. DO NOT MODIFY YOUR HELMET IN ANY WAY, IN PARTICULAR:

Do not modify the features of your helmet. Do not scratch, cut, or perforate the shell. Do not insert screws, and do not paint it again. Do not modify the use in any way. Do not remove any of the helmet's rubber rims. Their main purpose is to protect you from the sharp edges of the shell. Removing them could prove extremely dangerous in case of an accident. Do not modify in any way the padding. Please remember to use only original spare parts.

5. SIZING INSTRUCTIONS.

A safe helmet is one that fits your head snugly. Wear your helmet and shake your head left to right and right to left. Shake your head backwards and forwards. Move your helmet with your hands. If you feel the helmet is loose, if it slips away on your head during these operations, you need a smaller size. If you feel constriction or pain, you need a larger one. Now perform what we call the "ROLLOFF TEST" (see picture AB). With one hand, grab the bottom edge of the helmet and try to dislodge it from your head by pulling it upwards and forward with moderate force. If your helmet can be removed from your head this way, it does not fit your head properly. Make sure you have unobstructed lateral view. Make sure you can turn your head to see what's behind you as far as it is safe and comfortable. Make sure you can breathe comfortably and that nothing obstructs free flow of air coming from below your nose and mouth.

6. SHIELD CARE AND MAINTENANCE.

To clean your shield and maintain its characteristics as long as possible, use warm demineralized water and soap. Do not use water rich in chlorine. Never use alcohol or other solvents. Never use glass-cleaning products sold on the market; they normally contain alcohol. Always remove your shield before cleaning inside your helmet (see instructions #7 below). Reassemble only AFTER you have assured yourself that the cleaning products you used have fully evaporated.

7. POSITIONING.

Do not wear your helmet and/or buckle it if and when it is hanging on your head (as shown in picture A). Always wear your helmet in its correct position (as shown in picture B).

8. CLEANING.

Clean your helmet outside only with tepid water [not warm] and a few drops of

neutral soap or clean with specific products. Dry the helmet at ambient temperature: never expose it to a heat source.

9. TO FASTEN AND UNFASTEN THE CHIN STRAP.

While wearing your properly sized and fitted helmet on your head (follow instructions #1 and #3), tightly fasten the chin strap by passing the end of the strap through both D-shaped rings. Now thread the end of the strap over one D-ring and through the second one (as shown in picture A) and pull it comfortably tight, back against your throat. To unfasten the chin strap, simply pull the red tab attached to one of the D-rings and unthread the chin strap as shown in the picture. Engage the buckle insert tongued section into housing and push firmly until the tongue locks into position (picture B). Always ensure the chin strap is adjusted so the helmet is held securely in position when the buckle is closed. To release, push the red slide to the up position and simultaneously pull down the tongued section.

10. TAKE GOOD CARE OF YOUR HELMET: DO NOT LEAVE IT HANGING FROM ANY HOOK OF YOUR MOTORCYCLE.

Your helmet is sturdy and tough. Nevertheless, it should be handled with the utmost care. YOUR SAFETY DEPENDS ON IT. Never ride with your helmet hooked on your motorcycle. Make sure you always keep it a safe distance from the muffler and, in general, from any source of heat. In hot weather, always protect your helmet from direct sunlight when you are not riding, particularly if it is painted in dark colours.

11. KEEP HELMET OUT OF THE REACH OF PETS

To avoid the interior being chewed like a shoe, or scratched like a sofa, as too often happens. Such damage can be irreparable.

12. KEEP YOUR HELMET IN A SAFE PLACE

Do not “park” helmet on mirror stalks or bars to avoid damage to the liner.

13. DO NOT EXPOSE YOUR HELMET TO SOLVENTS

Including gasoline or their fumes, to avoid damage to shields, small plastic components, and interior.

Manufacturer: Shanghaimuxinmuyeyouxiangongsi

Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN.

Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREET EASTWOOD NSW : Australia

Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

UK

REP

YH CONSULTING LIMITED.

C/O YH Consulting Limited Office 147, Cent

House, London Road, Staines-upon-Thames,

Surrey, TW18 4AX

EC

REP

E-CrossStu GmbH

Mainzer Landstr.69,

60329 Frankfurt am Main.

VEVOR®

TOUGH TOOLS, HALF PRICE

Technical Support and E-Warranty Certificate

www.vevor.com/support

VEVOR®

TOUGH TOOLS, HALF PRICE

NEED HELP? CONTACT US!

3. PROPER SIZING AND POSITIONING.

1. DO NOT MODIFY YOUR HELMET IN ANY WAY, IN PARTICULAR:

1. SIZING INSTRUCTIONS.

6. SHIELD CARE AND MAINTENANCE.

1. TAKE GOOD CARE OF YOUR HELMET: DO NOT LEAVE IT HANGING ON A HOOK OF YOUR MOTORCYCLE

11. KEEP THE HELMET OUT OF REACH OF PETS

12. STORE YOUR HELMET IN A SECURE PLACE

13. DO NOT EXPOSE YOUR HELMET TO SOLVENTS

A/S YH Consulting Limited Office 147, Centurion

House, London Road, Staines-upon-Thames,

Surrey, TW18 4AX

E-CrossStu GmbH

Mainzer Landstr.69,

Modell	Größe	Bild
MD-820A	L (59–60 cm)
	M (57–58 cm)
	S (55–56 cm)
	XL (61 cm)
MD-808	L (58 cm)
	M (57 cm)
	S (55–56 cm)
	XL (59 cm)
MD-202	L (59–60 cm)
	M (57–58 cm)
	S (55–56 cm)
	XL (61 cm)

USER MANUAL

10. TAKE GOOD CARE OF YOUR HELMET: DO NOT LEAVE IT HANGING ON A HOOK OF YOUR MOTORCYCLE

12. STORE YOUR HELMET IN A SECURE PLACE.

C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX

www.vevor.com/support

VEVOR®

TOUGH TOOLS, HALF PRICE

4. DO NOT MODIFY YOUR HELMET IN ANY WAY, IN PARTICULAR:

5. INSTRUCTIONS FOR SIZES.

A

B

9. TO FASTEN AND UNFASTEN THE STRAP UNDER THE CHIN.

10. TAKE CARE OF YOUR HELMET: DO NOT HANG IT ON ANY HOOK OF YOUR MOTORCYCLE

11. KEEP THE HELMET OUT OF THE REACH OF ANIMALS

12. STORE THE HELMET IN A SAFE PLACE. Do not

13. DO NOT EXPOSE YOUR HELMET TO SOLVENTS

Imported in AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia

Imported in the USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

CONSULTING YH LIMITED.

C/O YH Consulting Limited Office 147, Centurion

House, London Road, Staines-upon-Thames,

4. DO NOT MODIFY YOUR HELMET IN ANY WAY, IN PARTICULAR:

6. CARE AND MAINTENANCE OF THE SHIELD.

A

B

9. TO ADJUST AND READJUST THE CHIN STRAP.

11. KEEP THE HELMET OUT OF THE REACH OF

Casa, London Road, Staines-upon-Thames,

Surrey, TW18 4AX

E-CrossStu GmbH

NEED HELP? CONTACT US!

3. SIZE SELECTION AND CORRECT ADJUSTMENT.

1. DO NOT MODIFY YOUR HELMET IN ANY WAY, IN PARTICULAR:

1. INSTRUCTIONS REGARDING SIZES.

6. CARE AND MAINTENANCE OF THE SHIELD.

1. TAKE CARE OF YOUR HELMET: DO NOT LEAVE IT HANGING ON ANY MOTORCYCLE HOOK

11. KEEP THE HELMET OUT OF THE REACH OF PETS

12. STORE THE HELMET IN A SAFE PLACE To

1. DO NOT EXPOSE THE HELMET TO SOLVENTS

C/O YH Consulting Limited Office 147, Centurion

House, London Road, Staines-upon-Thames,

Surrey, TW18 4AX

Przedstawiciel UE

E-CrossStu GmbH

Mainzer Landstr.69,

60329 Frankfurt am Main.

VEVOR®

TOUGH TOOLS, HALF PRICE

NEED HELP? CONTACT US!

SAFETY WARNINGS

3. SIZE AND CORRECT POSITIONING.

5. SIZING INSTRUCTIONS.

6. CARE AND MAINTENANCE OF THE VISOR.

10. TAKE GOOD CARE OF YOUR HELMET: DO NOT HANG IT ON A HOOK OF YOUR MOTORCYCLE

11. KEEP THE HELMET OUT OF REACH OF PETS To

12. STORE YOUR HELMET IN A SAFE PLACE Park

13. DO NOT EXPOSE YOUR HELMET TO SOLVENTS

C/O YH Consulting Limited Office 147, Centurion

House, London Road, Staines-upon-Thames,

Surrey, TW18 4AX

E-CrossStu GmbH

Mainzer Landstr.69,

warranty certificate www.vevor.com/support

VEVOR®

TOUGH TOOLS, HALF PRICE

NEED HELP? CONTACT US!

3. SIZE AND CORRECT POSITIONING.

4. DO NOT MODIFY YOUR HELMET IN ANY WAY, ESPECIALLY:

5. STORAGE INSTRUCTIONS.

6. HELMET CARE AND MAINTENANCE.

1. ALWAYS TURN YOUR HELMET OVER: DO NOT LEAVE IT HANGING FROM ANY HOOK ON YOUR MOTORCYCLE

13. DO NOT EXPOSE YOUR HELMET TO SOLVENTS

C/O YH Consulting Limited Office 147, Centurion

House, London Road, Staines-upon-Thames,

Surrey, TW18 4AX

EC

REP

E-CrossStu GmbH

Mainzer Landstr.69,

60329 Frankfurt am Main.

VEVOR®

TOUGH TOOLS, HALF PRICE

www.vevor.com/support