DLP-100W - Lighting Dörr - Free user manual and instructions

USER MANUAL DLP-100W Dörr

Technical diagram of a mechanical device with grid pattern and directional arrow (no text or symbols)

10.3 ROHS KONFORMITÄT

THANK YOU very much for choosing a quality product from DÖRR.

Please read the instruction manual and the safety instructions carefully before using the device for the first time.

Keep this instruction manual together with the device for later use. If other people use this device, provide them with this instruction manual. If you sell the device, the instruction manual is part of the device and must be supplied with it.

DÖRR is not liable for damage caused by improper use or failure to observe the instruction manual and safety instructions.

In the event of damage caused by improper handling or by external influence, the guarantee or warranty becomes void. Manipulation, structural alteration of the product, as well as opening the housing by the user or unauthorised third parties, is considered improper handling.

01 | ⚠ SAFETY INSTRUCTIONS

⚠️ ATTENTION! The following safety instructions must be observed before use:

• This continuous light is to be used exclusively for illumination for photographic purposes. This device is not suitable for permanent room lighting!
• Do not look directly into the LEDs and do not point the light beam directly into the eyes of people or animals. ATTENTION: Looking into the LEDs for a long time can cause irreversible retinal damage in the eye!
• Do not use or touch the continuous light with wet hands! Make sure to use it on dry ground.
• People with physical or cognitive impairments should only operate the continuous light under guidance and supervision.
• Persons with a pacemaker, defibrillator or other electrical implants should keep a minimum distance of 30 cm, as the continuous light generates magnetic fields.
• The continuous light is not a toy! Keep the continuous light, accessories and packing materials away from children and pets to prevent accidents and suffocation.
• When folding or unfolding, as well as when aligning the shielding flaps, there is a risk of pinching. Watch your fingers. Attention: The shielding flaps heat up during operation. There is a risk of burns!
• Protect the continuous light from rain, moisture, direct sunlight and extreme temperatures.
• Make sure that the continuous light is placed securely and cannot tip over. There is a risk of fire! To avoid tipping of the LED light, align the LED light over a wide tripod leg. Make sure that your light stand is placed on a level and dry surface.
• Only use the continuous light with the mains adapter supplied. Do not use an extension cable. Make sure that no one can trip over the cable connections.
• Only connect the continuous light to a socket with a mains voltage of 100-240V.
• Only use the continuous light with a special V-Mount Li-Ion battery suitable for this continuous light (optionally available).

• Before disconnecting the power or removing the battery (not included), switch off the continuous light at the main switch.

• Ensure sufficient ventilation during operation. Never cover the ventilation slots of the continuous light. There is a risk of fire!

• High voltage can occur in the continuous light. If the continuous light is defective or damaged, do not attempt to disassemble or repair it yourself - there is a risk of electric shock! Please contact your specialist dealer.
• Protect the continuous light from impacts. Do not use the continuous light if it has been dropped. In this case, have the continuous light checked by a qualified electrician before switching it back on.
• Keep the continuous light away from easily flammable materials! There is a risk of fire!
• Do not place any foils, fabrics or other unsuitable filters and attachments in front of the LED surface. There is a risk of scorching and fire!

• If you notice a scorching smell, switch off the continuous light immediately at the main switch and disconnect the power connection. There is a risk of fire! Please contact your specialist dealer.

• Do not use the continuous light in the direct vicinity of devices that generate strong electromagnetic fields.

• Switch off the continuous light after use and allow it to cool down before touching the housing or the shielding flaps, or before storing the continuous light.
• After each use, switch off the continuous light at the main switch and disconnect the power connection.
• Protect the continuous light from dirt. Do not clean the continuous light with petrol or harsh cleaning agents. We recommend a lint-free, slightly damp microfibre cloth to clean the external components of the continuous light. Before cleaning, switch off the continuous light and disconnect the power connection or remove the battery!
• Store the continuous light in a dust-free, dry and cool place.
• Please dispose of the device when it is defective or no longer intended for use in accordance with the Waste Electrical and Electronic Equipment Directive WEEE. If you have any questions, please contact the local authorities responsible for disposal.

02 | PRODUCT DESCRIPTION

The DÖRR LED continuous light DLP-100W offers a high luminous intensity of max. 10,000 lux and is continuously dimmable. The colour temperature of the long-life LEDs can be variably adjusted from 3,200 K to 5,500 K. The light can be operated with the supplied mains cable or alternatively with a V-Mount Li-Ion battery (optionally available).

• 100 Watt power
  • 480 bi-colour LEDs
• Illuminance max. 10,000 lux/1m, continuously dimmable
• Colour temperature adjustable from 3,200 K to 5,500 K
• Outdoor operation possible with V-Mount Li-Ion battery (V-Mount battery optionally available from DÖRR)
• Stable, swivelling metal frame for mounting on a light stand (light stands are optionally available from DÖRR)
• Diffuser panel included
• Regulation by remote control possible (Remote control optionally available from DÖRR)

Accessories supplied only with SET article no. 373513:

• Two sturdy light stands max. height 1.80 m
• Robust bag with divider

03 | NOMENCLATURE

01 Pivoting screening cover
02 LED luminous surface with diffuser panel
03 Release button for diffuser panel
04 Locking screws swivel frame
04a) Rubber O-ring black
04b) Washer silver
05 Swivel mount
06 Locking screw lamp stand
07 Tripod light mount
08 Handles
09 Ventilation slots
10 V-Mount battery connection
11 Release button V-mount battery
12 Battery contacts
13 Colour temperature display
14 Illuminance display

15 Rotary control (blue) for setting colour temperature/channels
16 Rotary control (white) for setting the illuminance/groups
17 Main switch (0= Off / I= On)
18 Connection socket "IN" for mains cable
19 Power supply
19a) Connector
19b) Screw lock

Only with SET article no. 373513:

20 Light tripod

20a) Threaded spigot
20b) Locking screws for 3 pull-outs
20c) Locking screw for tripod legs
20d) Centre struts

04 | OPERATION

Note: Before using for the first time, carefully remove the protective film from the LED diffuser panel and from the display.

04.1 Mounting the swivelling bracket

To mount the continuous light on the swivelling bracket (05) screw the two locking screws (04) each with the black rubber ring (04a) and the silver washer (04b) like shown in the following sketch:

04a 04b 04 05

04.2 Mounting on light stand

Mount the continuous light on a light stand (optionally available from DÖRR) as described below.

Only with SET article no. 373513:

Pull the tripod legs down until the centre struts (20d) are approximately horizontal. Tighten the locking screw (20c).

Slightly loosen the locking screws (20b) to adjust the lamp stand with the 3 extensions to the desired height. Tighten the locking screws (20b) again.

Screw the locking screw (06) all the way in and place the light stand holder (07) on the threaded spigot (20a).

ATTENTION: To avoid tilting of the LED light, align the light surface of the continuous light over a wide tripod leg.

Tighten the locking screws (06) again.

Loosen the side locking screws (04) on the swivelling bracket (05) to align the continuous light. Tighten the locking screws (04) again.

ATTENTION: To align the continuous light during operation, touch the continuous light only on the two handles (08).

04.3 Removing/attaching the diffuser panel

To remove the diffuser panel, press the release button (03) down and slide the panel out of the guide rails to the right.

Technical diagram of a mechanical device with grid pattern and directional arrow (no text or symbols)

To refit the diffuser panel, make sure that the panel is inserted in the upper and lower guide rails. Slide the panel to the left until the release button (03) sticks out completely again. You may have to lift the panel slightly on the left-hand side to be able to push the panel in as far as it will go.

04.4 Operation with power adapter

Make sure that the main switch (17) is in position "0" (= off). Insert the connector (19a) into the socket (18) at the LED light. Pay attention to the pins and holes. Screw tight the screw lock (19b).

IMPORTANT: To disconnect the cable connection, make sure to open the screw lock (19b) first!

Connect the power supply (19) to a socket with a mains voltage of 100-240V.

ATTENTION: Do not use an extension cable. Make sure that no one can trip over the cable connections.

04.5 Operation with V-Mount Li-Ion battery (optional)

ATTENTION:

Operate the continuous light only with a special V-Mount Li-Ion battery suitable for the continuous light (optionally available). When inserting the battery, pay attention to the correct polarity (+/-). When not in use for a longer period of time, please remove the battery.

Make sure that the main switch (17) is in position "0" (= off). Push the battery into the V-shaped battery connector (10) from the right until the battery audibly clicks into place. To remove the battery again, make sure that the main switch (17) is in position "0" (= off). Press the unlock button (11). Slide the battery out of the connector to the right.

V-Mount Li-Ion batteries optionally available from DÖRR:

DÖRR Compact V-Mount Li-Ion Battery CVL-98 14.8V, 98Wh

Switch the continuous light on the main switch (17) to position I (=On).

05 | SETTINGS

05.1 Setting the colour temperature

To adjust the colour temperature in 20 K steps, turn the blue control dial (15):

• To the right for cold light with a colour temperature of up to max. 5,500 K
• To the left for warm light with a colour temperature of up to min. 3,200 K

The set value is shown in the display for colour temperature (13).

05.2 Setting the illuminance

To adjust the illuminance (brightness), turn the white control dial (16):

• To the right for brighter light up to max. 99% (corresponds to 100%)
  • To the left for darker light up to min. 0%

The set value is shown in the display for illuminance (14).

ATTENTION: After each use, switch off the continuous light at the main switch (17) and disconnect the power connection.

06 | FURTHER FUNCTIONS

06.1 Control via remote control

You have the option of controlling the settings of the DLP-100W LED continuous light via remote control. The corresponding remote control is available separately from DÖRR:

Remote control for DLP-100W/DLP-100W

Article no. 373516

06.1.1 Setting the radio channel on the LED permanent light DLP-70W

Press the control dial (15) to set the colour temperature/channels. The permanent light display then shows the set group and next to it the set channel, e.g. A03, instead of the colour temperature. To change the channel, turn the control dial until the desired channel appears. Possible channel selection: 00 to 50. After approx. 2 seconds, the display jumps back to the colour temperature.

06.1.2 Setting the group on the LED permanent light DLP-70W

Press the rotary control (16) to set the illumination level/groups. The set group, e.g. A, appears on the lamp display instead of the colour temperature. To change the group, turn the control dial until the desired group appears. Possible group selection: A, B, C, D, E and F. After approx. 2 seconds the display jumps back to the colour temperature.

For further instructions on use, please refer to the operating instructions for the remote control (click here).

07 | CLEANING AND STORAGE

Do not clean the unit with petrol or harsh cleaning agents. We recommend a lint-free, slightly damp microfibre cloth to clean the outer components of the unit. Before cleaning, switch off the unit and disconnect the power supply or remove the battery. Store the unit in a dust-free, dry, cool place. The unit is not a toy – keep it out of reach of children! Keep the unit away from pets.

08 | TECHNICAL DATA

Number of LEDs	480 Bi-colour
LED frequency 20,000 Hz
Illuminance approx.	10,000 lux/1 m40,000 lux/0.5 m
Colour temperature	3,200 – 5,500 K
Output power 100 W
Colour rendering index	CRI > 95 Ra
Operating voltage	DC 14,8 V 7 A
Power supply	AC 100-240 V ~ 50/60 Hz, DC 15,5V 10AAlternatively with V-Mount battery (optionally available)
Frequency band	2,400 – 2,483 MHz
Dimensions of illuminated surface approx.	45 x 25.5 cm
Dimensions approx.	58 x 38 x 10 cm
Weight approx..	4,255 g

Only with SET article no. 373513:

LIGHT STAND
Height max. approx. 180 cm
Height min. approx. 62 cm
Transport dimensions approx.	56 cm
Pull-outs 3
Connection	Spigot with 1/4" thread
Material	Aluminium/plastic
Load capacity max. approx.	5 kg
Weight approx.	1,230 g
BAG
Dimensions approx.	60x33x26 cm
Number of partition walls	2
Material	Polyester

Dörr GmbH reserves the right to make technical changes without notice.

09 | SCOPE OF DELIVERY

LED continuous light DLP-100W

Article no. 373512

1x LED continuous light
1x Power supply
1x Diffuser filter panel
1x Safety instructions

LED continuous light SET DLP-100W

Article no. 373513

2x LED continuous light
2x Power supply
2x Diffuser filter panel
2x Light tripod
1x Bag
1x Safety instructions

10 | DISPOSAL, CE MARKING

10.1 BATTERY DISPOSAL

Batteries and rechargeable batteries are marked with the symbol of a crossed-out waste bin. This symbol indicates that empty batteries or rechargeable batteries that can no longer be recharged must not be disposed of in household waste. Old batteries may contain harmful substances that can cause damage to health and the environment. As the end user, you are legally obliged to return used batteries (Battery Act §11 Act on the Reorganisation of Waste Product Responsibility for Batteries and Accumulators). You can return batteries free of charge after use at the point of sale or in your immediate vicinity (e.g. at municipal collection points or in shops). You can also return batteries to the seller by post.

10.2 WEEE NOTICE

The WEEE (Waste Electrical and Electronic Equipment) Directive, which came into force as European law on 13 February 2003, led to a comprehensive change in the disposal of discarded electrical equipment. The primary purpose of this directive is to prevent e-waste while promoting reuse, recycling and other forms of reprocessing in

order to reduce waste. The WEEE logo (waste bin) shown on the product and on the packaging indicates that the product must not be disposed of with normal household waste. You are responsible for delivering all discarded electrical and electronic equipment to appropriate collection points. Separate collection and sensible recycling of e-waste helps to use natural resources more sparingly. Furthermore, the recycling of e-waste contributes to preserving our environment and also people's health. Further information on the disposal of electrical and electronic equipment, recycling and collection points can be obtained from local authorities, waste disposal companies, specialist retailers and the manufacturer of the device.

10.3 ROHS CONFORMITY

This product complies with the European RoHS Directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment and variations thereof.

10.4 CE MARK

The imprinted CE mark complies with the applicable EU standards and indicates that the device meets the requirements of all EU directives applicable to this product.

11 | SIMPLIFIED EU DECLARATION OF CONFORMITY

Hereby, DÖRR GmbH declares that the radio equipment type [373512, 373513] is in compliance with directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.doerr-foto.de.

Technical diagram of a mechanical device with internal grid structure and directional arrow (no text or symbols)

10 | ÉLIMINATION, MARQUAGE CE

10.1 ÉLIMINATION DES PILES/DE LA BATTERIE

10.3 CONFORMITÉ ROHS

Technical diagram of a mechanical device with internal grid structure and directional arrow (no text or symbols)

10.3 CONFORMIDAD CON ROHS

04 | PRIMA ACCENSIONE

Technical diagram of a mechanical device with internal grid structure and directional arrow (no text or symbols)

2x Luci continue a LED

10.3 CONFORMITÀ ROHS