A82TXPS - Electric saw Cramer - Free user manual and instructions

USER MANUAL A82TXPS Cramer

Line drawing of a mechanical tool or device with a handle and internal components (no text or symbols)

cramer.eu

EN

Product Overview

Your machine has been engineered and manufactured to high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of trouble-free performance.

Know your pole saw head

1 Pole saw head
8 Release button
2 Chain cover lock nut
9 Cutters
3 Oil tank
10 Cutters chain rotation
4 Bar
11 Drive links
5 Chain
12 Bar groove
6 Scabbard
13 Chain adjustment screw
7 Knob

Assembly

Insatll the pole saw head (see Figure 2)

1 Remove the rubber protector.
2 Loosen the knob on the coupler.
3 Push in the release button located on the lower shaft. Align the release button with the positioning hole and slide the two shafts together. Rotate the lower shaft until the button locks into the positioning hole.
4 Tighten the knob securely.

Operation

Adding bar and chain lubricant (see Figure 3)

Use Bar and Chain Lubricant. It is designed for chains and chain oilers, and is formulated to perform over a wide temperature range with no dilution required. NOTE: Pole saw comes from the factory with no bar and chain lubricant added. Level should also be checked after every 20 minutes of use and refilled as needed.

1 Unscrew and remove the cap from the oil tank.
2 Pour oil in the tank and monitor the level on the indicator.
3 Make sure no impurities penetrate the oil tank when filling.
4 Screw on the oil cap and tighten it.

NOTE: Do not use dirty, used or otherwise contaminated oils. Damage may occur to the bar or chain.

NOTE: It is normal for oil to seep from the saw when not in use. To prevent seepage, empty the oil tank after each use then run for one minute. When storing the unit for a long period of time (three months or longer) be sure the chain is lightly lubricated; this will prevent rust on the chain and bar sprocket.

Preparation for cutting

• Wear non-slip gloves for maximum grip and protection.
• Maintain a proper grip on the unit whenever the motor is running. Use your right hand to firmly grip the rear handle while your left hand has a firm grip on the pole shaft.
• Hold unit firmly with both hands. Always keep your left hand on the pole shaft and your right hand on the rear handle, so your body is to the left of the chain line. Never use a left-handed (cross-handed) grip, or any stance that places your body or arm across the chain line.
  • Never stand directly under the limb you are cutting.
• Be certain the collars are fully tightened before operating equipment; check them periodically for tightness during use to avoid serious injury.

Work techniques

Delimbing a tree (see Figure 4)

WARNING!

Make sure there is nothing or nobody in the area where the branches will fall.

• Stand opposite the branch you want to cut.
- Start cutting lower branches followed by the higher ones.
• Cut downwards to prevent the bar from getting jammed.

Limbing tree branches (see Figure 5)

Limbing means removing the branches from a felled tree.

WARNING!

Be careful of where the branches are lying on the ground, the risk of them being under tension, the direction the branch may go during cutting and the risk of the tree being unstable after the branch has been cut.

When limbing, it is necessary to leave the lower, larger branches to support the trunk on the ground. Remove the small branches with a single cut. It is recommended to cut the tensioned branches working from the bottom upwards to prevent the pole saw from bending.

MAINTENANCE

Adjusting the chain tension (see Figure 6.10.11)

• Untighten the chain cover lock nut slightly by turning it counterclockwise. You do not need to remove the chain cover in order to adjust the chain tension.
• Rotate the chain adjustment screw clockwise to increase the chain tension and rotate counterclockwise to decrease the chain tension.
  • Once the chain is at the desired tension, tighten the chain cover lock nut.

WARNING!

During normal saw operation, the temperature of the chain increases. The drive links of a correctly tensioned warm chain will hang approximately 1/16 in. (1,58 mm) out of the bar groove.

WARNING!

New chains tend to stretch; check the chain tension frequently and tension as required.

Assemble the bar and chain (see Figure 6-11)

• Loose the lock nut and remove the chain cover.
• The bar contains a bar stud slot that fits over the bar stud. The bar also contains a chain tension pin hole which fits over the chain tensioning pin
• Place the bar onto the bar stud so that the chain tensioning pin fits into the chain tensioning pin hole.
• Fit the chain over the sprocket and into the bar groove. The cutters on the top of the bar should face toward the bar tip, in the direction of the chain rotation.
• Replace the chain cover.
• Remove all slack from chain by turning the chain tensioning screw clockwise, assuring that the chain seats into the bar groove during tensioning.
• Lift the tip of the bar up to check for sag. Release the tip of the bar, and turn the chain tensioning screw 1/2 turn clockwise. Repeat this process until sag does not exist.
• Hold the lip of the bar up and tighten the lock nut securely.
• Chain is correctly tensioned when there is no slack on the underside of the bar, the chain is snug, but it can be turned by hand without binding.
• Tighten the lock nut.

NOTE: If the chain is too tight, it will not rotate. Loosen the chain cover lock nut slightly and turn the chain adjustment screw 1/4 turn counterclockwise. Lift the tip of the guide bar up and retighten the chain cover lock nut. Ensure that the chain will rotate without binding.

EN

Cleaning

Cleaning the machine and the motor

After every work session, clean the machine thoroughly to remove all dust and debris.

• To reduce fire hazards, keep the machine and, in particular, the motor free of leaves, branches or excessive grease.
• Always clean the machine after use with a damp cloth dipped in neutral detergent.
- Remove all traces of moisture using a soft damp cloth. Moisture can generate risks of electric shocks.
- Do not use aggressive detergents or solvents to clean the plastic parts or handgrips.
- Do not spray water onto the motor and electrical components and prevent them from getting wet.
- To avoid overheating and damage to the motor or the battery, always keep the cooling air vents clean and free of debris.

Cleaning the chain

Remove any traces of sawdust or oil deposits from the chain every time it is used.

If there is excessive dirt or resin build-up, disassemble the chain and place it in a container with a specific cleanser for a few hours. Then rinse it with clean water and treat it with a suitable anticorrosive spray, before reassembling on the machine.

Troubleshooting

PROBLEM PROBABLE CAUSE POSSIBLE SOLUTION *
Pole saw fails to operate.	The poles are not assembled correctly.	Reassemble the poles according to the instructions.

Bar and chain running hot and smoking.	No oil in the oil tank. Refill oil into the oil tank.
	The discharge port is blocked by debris.	Refer to the manual to remove the bar and clean out the debris.
	Inlet opening in inner oil tank is blocked by debris.	Clean the oil tank, and refill with clean bar and chain lubricant.
	The sprocket is stuck and clogged with debris.	Clean the sprocket and refill with clean bar and chain lubricant.
	Chain tension for overtightened or loose condition.	Refer to Re-tensioning the saw chain in the manual.
The chain does not cut.	Dull chain. Sharpen or replace the chain.
	Chain on backwards.	Refer to Replacing the Bar and Chain assembly earlier in this manual.
Motor running, but cutting abnormal	Lack of bar and chain lubricant can cause increased friction. Chain needs to be properly maintained.	Make sure the pole saw always has bar and chain lubricant.

* If the fault is not solved, you must go to your distributor and/or nearest Authorized Technical Service.

Technical Data

PROPERTY VALUE
Guide bar length	10" (254 mm)

Produktüberblick

1 Remove the rubber protector.
2 Loosen the knob on the coupler.
3 Push in the release button located on the lower shaft. Align the release button with the positioning hole and slide the two shafts together. Rotate the lower shaft until the button locks into the positioning hole.
4 Tighten the knob securely.

Funzionamento

After every work session, clean the machine thoroughly to remove all dust and debris.

• To reduce fire hazards, keep the machine and, in particular, the motor free of leaves, branches or excessive grease.
• Always clean the machine after use with a damp cloth dipped in neutral detergent.
- Remove all traces of moisture using a soft damp cloth. Moisture can generate risks of electric shocks.
- Do not use aggressive detergents or solvents to clean the plastic parts or handgrips.
- Do not spray water onto the motor and electrical components and prevent them from getting wet.
• To avoid overheating and damage to the motor or the battery, always keep the cooling air vents clean and free of debris.

Limpeza da corrente

Installer stangsaghodet (Se Fig 2)

Klargjøring For Saging

Adding bar and chain lubricant (Bkz. Şekil 3)