BAS 18-2/1H - Drill Bavaria by Einhell - Free user manual and instructions

Product type	Cordless drill/driver
Brand	Bavaria by Einhell
Model	BAS 18-2/1H
Motor voltage	18 V
No-load speed (1st gear)	0 - 400 rpm
No-load speed (2nd gear)	0 - 1150 rpm
Adjustable torque	17 positions
Rotation direction	Right and left
Chuck capacity	1.5 - 10 mm
Battery type	Nickel-Cadmium (Ni-Cd)
Number of batteries included	2
Charger voltage	230 V / 50 Hz
Charging current	2 A
Weight	1.8 kg
Sound pressure level	72 dB(A)
Sound power level	82 dB(A)
Vibration	< 2.5 m/s²
Package contents	Drill, 2 batteries, charger, case, 6 HSS drill bits, 6 bits, bit holder
Safety	Moisture protection, switch lock in central position
Maintenance	Recharge regularly, do not fully discharge, clean after use

Frequently Asked Questions - BAS 18-2/1H Bavaria by Einhell

How to charge the battery for the first time?

Before first use, the Ni-Cd battery must be charged for about 5 charge/discharge cycles to reach its maximum capacity. Use the supplied charger and connect it to the 230 V mains. Let the battery cool down if it is hot before charging.

What to do if the drill does not start?

Check that the battery is charged and correctly inserted. Make sure the rotation direction switch is not in the central position (locked). If the problem persists, contact customer service.

How to adjust the torque setting?

Turn the torque setting ring (fig. 1) to one of the 17 steps. For screwing, choose a setting suitable for the screw and material. The maximum torque is reached at the last step (drilling position).

How to use the drilling mode?

Set the torque setting ring to the last step marked 'Bohrer' or 'Bohren' (drilling). This disables the torque limiter, allowing maximum power for drilling.

How to change the rotation direction?

Use the slide switch above the On/Off switch. Push it to the right for clockwise rotation, to the left for counterclockwise rotation. Only switch when the drill is stopped to avoid damaging the gear.

How to maintain the Ni-Cd battery?

Recharge the battery regularly, even if not in use, as it self-discharges. Never fully discharge it. Avoid high temperatures. For a long service life, perform about 5 complete charge/discharge cycles.

Can I use drill bits of different sizes?

Yes, the chuck accepts drill bits from 1.5 to 10 mm. Use sharp bits suitable for the material. For screws, use appropriate screwdriver bits (Torx, Phillips, etc.).

What to do if the battery heats up during use?

Under heavy load, the battery may heat up. Let it cool to room temperature before recharging. Never charge a hot battery.

How to clean the drill?

Clean the tool with a dry cloth. Avoid any contact with water or moisture. Ensure the ventilation slots are clear. Do not use harsh chemicals.

Where to dispose of used batteries?

Do not dispose of Ni-Cd batteries in household waste as they contain toxic cadmium. Return them free of charge to a suitable collection point or to ISC customer service.

USER MANUAL BAS 18-2/1H Bavaria by Einhell

Open hard-shell tool kit with drill bit, battery pack, and wiring (no visible text or labels)

Lieferumfang:

1 cordless drill/screwdriver
2 removable batteries
1 battery charger
1 storage case
6 HSS bits
6. bit Inserts
1 bit holder

① Elementi forniti

Figure 1: Torque adjustment facility

Figure 2: Bit holder

Figure 3: Forward / Reverse selector switch

Figure 4: On/Off switch

Figure 5: Removable battery pack; press both clips to take out the battery pack

Important notes:

It is imperative to read these notes before putting your battery-powered drill/screwdriver into operation:

1. The removable Ni-Cd battery pack supplied with your battery-powered drill/screwdriver has to be charged before you use the tool for the first time.

2. Use the supplied battery charger to charge the battery pack. It takes a maximum of 1 hour to charge an empty battery. Do not use the supplied battery charger to charge any other tools or appliances.

3. The battery pack reaches its maximum capacity after approx. five discharge/charge cycles.

4. Ni-Cd batteries will also discharge when they are not in use. It is recommended, therefore, to charge the batteries regularly.

5. Please note the data quoted on the rating plate of the battery charger. Operate the charger only from the same mains voltage as that quoted on the rating plate.

6. In periods of heavy duty the battery pack will grow warm. Allow the battery pack to cool to room temperature before starting to charge it.

Safety regulations:

1. Protect your battery-powered drill/screwdriver and charger from the damp and rain.
2. Keep the charger and battery-powered drill/screwdriver safe from children.
3. Use only sharp drill bits and undamaged, properly fitting screwdriver bits.
4. Wear suitable working clothes and safety goggles.
5. Never use the battery-powered drill/screwdriver and charger in the vicinity of vapours and combustible liquids.
6. Look for concealed electric cables, gas pipes and water pipes before drilling and screwdriving in walls.
7. Never throw old batteries into an open fire. Risk of explosion!
8. Avoid contact with leaky batteries. Should contact arise nevertheless, wash the affec-

GB

ted area of skin immediately with soap and water. If battery acid gets in your eye, rinse the eye with clear water for at least 10 minutes and consult a doctor immediately.

1. Protect the charger and its cable from damage and sharp edges. Damaged cables are to be replaced immediately by an electrician.
2. Examine your tool for any signs of damage. Have repairs carried out only by an electrician.
3. Make sure that the contacts of the Ni-Cd battery pack do not touch other metallic objects, e.g. nails and screws. Risk of short-circuiting!

Putting into operation: Loading the Ni-Cd battery pack

1. Check that your mains voltage is the same as that quoted on the rating plate. Insert the charger in a socket-outlet.
2. Pull the battery pack out of the handle (Figure 5) by depressing the clips on the side.
3. nsert the battery pack in the charger. The red light comes as a sign that the battery pack is being charged. The green LED comes on to signal that the charging is completed. It takes 1 hour to charge an empty bat-

tery. The temperature of the battery may rise slightly during the charging operation. This is normal.

If the battery pack fails to become charged, please check

● whether there is voltage at the socket-outlet
● whether there is proper contact at the charging contacts on the charger.

If the battery still fails to become charged, please return

● the charger

● the battery pack

to our Customer Service Department.

Timely recharging of the Ni-Cd battery pack is recommended in the interest of long battery life. Recharging is always necessary when you notice that the power of the battery-powered drill/screwdriver is decreasing.

Never allow the battery pack to discharge completely. This will result in damage to the Ni-Cd battery pack!

Adjusting the torque (Figure 1)

The Einhell battery-powered drill/screwdriver is equipped with a 17-step mechanical torque adjustment facility. The torque for a specific size of screw is selected with

GB

the set-collar (Figure 1). The correct torque depends on several factors:

● on the type and hardness of material in question
● on the type and length screws used
● on the requirements needing to be met by the screwed joint.

The clutch disengages with a gra- ting sound to indicate when the set torque is reached.

Drilling

For drilling purposes, move the set-collar to the last step „Drill“ (Figure 1). In this setting the slip clutch is inactive. The maximum torque is available in drilling mode.

Forward/Reverse switch (Figure 3)

With the slide switch above the On/Off switch you can select the direction of rotation of the battery-powered drill/screwdriver and secure it against being switched on accidentally. You can choose between clockwise and anticlockwise rotation. To avoid causing damage to the gearing it is advisable to change the direction of rotation only when the tool is at a standstill.

The On/Off switch is blocked when

the slide switch is in centre position.

On/Off switch (Figure 4)

Infinitely variable speed control is possible with the On/Off switch. The further you press the switch, the higher the speed of the battery-powered drill/screwdriver.

Screwdriving

We recommend using self-centering screws (e.g. Torx screws, recessed head screws) designed for reliable working. Be sure to use a bit that matches the screw in shape and size. Set the torque, as described elsewhere in these operating instructions, to suit the size of screw.

Technical data

GB

Voltage supply 18 V =

Speed 0-400 / 0-1150 rpm

Torque 17 levels

Forward and

reverse rotation yes

Chuck clamping

width 1.5 - 10 mm

Battery charging

voltage 18 V =

Battery charging

current 2 A

Mains voltage for

charger 230 V \~ 50 Hz

Sound pressure level

LPA: 72 dB(A)

Sound power level

LWA: 82 dB(A)

Vibration _w <2,5 m/s ^2

Weigth 1,8 kg

graph TD
    A["Warning"] --> B{Failure?}
    B -->|Yes| C["Error"]
    B -->|No| D["Monitor"]
    C --> E["ISC"]
    D --> E
    E --> F["Warning icon: person with cross"]

Old and defective batteries do not belong in the refuse bin. Think of the environment! Cadmium is toxic. For correct disposal, return old and defective batteries postage-paid to ISC or take them to your local old battery depot. Ask at your town hall for details of the old battery depots in your area.

F

graph TD
    A["Warning"] --> B{Error}
    B -->|Yes| C["ISC"]
    B -->|No| D["Failure"]
    C --> E["Warning icon"]
    E --> F["Warning icon with downward arrow"]
    F --> G["Warning icon with downward arrow"]

The undersigned declares in the name of the company that the product is in compliance with the following guidelines and standards.

The image contains no text or characters.

97/23/EG

□

R&TTED 1999/5/EG

X

89/336/EWG

The image contains a single, solid horizontal line, which is a stylistic or background element (like a rule line on paper). According to Rule 2, such lines must be ignored by the OCR result. Therefore, the corrected OCR text is:

[Empty]

2000/14/EG: L_WM dB(A); L_WA dB(A)

The image contains no text or characters.

90/396/EWG

EN 60335-1; DIN VDE 0700-207; prEN 50260-1; prEN 50260-2-1; prEN 50260-2-2; EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3

Eschenstraße 6 · D-94405 Landau/Isar (Germany)

Technical changes subject to change

The guarantee period begins on the sales date and is valid for 2 years.

Responsibility is assumed for faulty construction or material or functional defects.

Any necessary replacement parts an necessary repair work are free of charge.

We do not assume responsibility for consequential damage.

Your customer service partner

© GARANTIEURKUNDE

YU MP Trading d.o.o.

Cika Liubina 8/IV

YU 11000 Beograd

GR An. Mayrofidopoulos S.A.

Technical & Commercial company

12, Papastratou & Asklipiou Str.

GR 18545 Piräus

Tel [phone], Fax [phone]

RUS Bermas

Altufyevskove shosse, 2A

RUS 127273 Moscow

Tel [phone], Fax [phone]

EH 01/2003