P5728T - Doorbells Emos - Free user manual and instructions

Product type	Wireless doorbell
Brand	Emos
Model	P5728T
Button (transmitter) power supply	1 12 V battery type A23
Chime (receiver) power supply	3 1.5 V batteries type AAA (alkaline, non-rechargeable)
Transmission frequency	433.92 MHz
Transmission power	5 mW e.r.p. maximum
Range in open field	Up to 180 m
Protection rating (button)	IP56 (waterproof)
Pairing	Self-learning function via push button
Number of pairable buttons	Several (repeat procedure for each)
Settings	Melody selection and volume adjustment
Package contents	Double-sided adhesive tape
Button fixing	Double-sided adhesive tape or screws (not included)
Chime usage	Indoor only, dry rooms
Maintenance and cleaning	Soft damp cloth with a little soap; no solvents or harsh products
Safety precautions	Do not expose to shocks, high temperatures, direct radiation or humidity; use only alkaline batteries
Target audience	Not suitable for persons (including children) with reduced capacities without supervision
Compliance	Directive 2014/53/EU (declaration available online)
Disposal	Do not dispose of with household waste; use collection points for electronic waste

Frequently Asked Questions - P5728T Emos

How to pair the doorbell button with the chime?

Press and hold (about 4 seconds) the pairing button on the chime until you hear a melody. The chime enters pairing mode for 25 seconds. During this time, press the doorbell button. The chime rings to confirm pairing.

How to change the melody and volume?

Use the melody change/volume adjustment button (mark 5 on the chime) to browse melodies and adjust the volume.

How to clear the memory of paired buttons?

Insert 2 AAA batteries into the chime, then press and hold the lock button (). Then insert the third AAA battery while keeping the button pressed. The LED flashes then stays on. Release the button, the LED goes out: memory is cleared.

Which battery to use in the button?

The button requires a 12 V alkaline battery type A23. Ensure correct polarity during installation.

What is the range of the doorbell?

The range in open field can reach 180 meters. In a built environment (walls, obstacles), it may drop to about 20% of this value.

Is the button waterproof?

Yes, the button has an IP56 protection rating, making it weather-resistant. However, it is recommended to install it in a sheltered place for optimal lifespan.

Can several buttons be paired with one chime?

Yes, it is possible to pair multiple buttons. Repeat the pairing procedure for each button, one by one.

How to clean the chime and the button?

Use a soft slightly damp cloth with a little soap. Do not use harsh cleaning products or solvents. Before cleaning, remove the batteries from the chime.

Where to install the button for best reception?

Install the button on a non-metallic surface (wood, brick). Avoid metal objects or materials containing metal (e.g., metal window frames) as they can block the radio signal.

What to do if the chime does not ring?

First check the batteries: replace them with new alkaline batteries respecting polarity. Make sure the button is correctly paired (repeat pairing). Test the button by pressing: the red LED should light up, indicating signal transmission. Move the chime away from sources of metallic interference.

USER MANUAL P5728T Emos

Designed for wireless doorbell P5728.

Specifications

Transmission range: up to 180 m in an open area (can drop down to one fifth in a busy area)

Transmission frequency: 433.92 MHz, 5 mW e.r.p. max.

Button: water resistant; enclosure rating IP56

Pairing of chime with buttons: self-learning function

Button power supply: 1× 12 V battery (type A23)

Includes: double-sided adhesive tape

Button Description

(see Fig. 1)

1 - ring button

2 - button LED

3 – hole for opening the

battery cover

4 – battery compartment

Removing the Button's Battery Cover/Installing the Button

(see Fig. 2)

Chime Description

(see Fig. 3)

1 - bell LED

2 - battery compartment

3 – holes for hanging

4 - speaker

5 - ringtone change button

6 – pairing/volume setting button

Pairing the Button with the Chime

1. Remove the rear cover of the button by inserting a screwdriver into the hole on the bottom side. Insert a 12 V type A23 battery in the button. When inserting a battery, make sure to observe the correct polarity!

2. Insert 3× 1.5 V AAA batteries into the chime. When inserting the batteries, make sure to observe the correct polarity. Use alkaline batteries only; do not use re-chargeable batteries.

3. Long-press (ca. 4 seconds) the pairing button on the chime; a tone will sound. The chime will switch to self-learning pairing mode which lasts for 25 seconds. During this time, press the

ring button. The chime will ring and the button is now paired with the chime. This automatically ends self-learning mode.

1. Re-assemble the button.

2. To pair multiple buttons, repeat the process for each button from step 1.

Wiping the Memory of Paired Buttons

Insert 2 AAA batteries into the doorbell, then press and hold the button. Insert the remaining third AAA battery into the doorbell. The doorbell's LED will flash and then remain lit. Release the button; the LED will turn off. This will erase the memory of all paired buttons.

Installation of the Doorbell (Transmitter) Button

1. Begin by pairing the button with the chime.
2. Before installation, check that the pair works reliably in the chosen spot.

3. Remove the rear cover with a screwdriver through a hole on the side of the button.

4. Use the double-sided adhesive tape (included) or two screws to fix the rear portion of the cover to the wall. Although the button is weather resistant, choose a location where it is protected, e.g. in a wall recess.

5. Re-assemble the button.

6. Press the button to ring the chime. Pressing is accompanied by LED illumination indicating the button has sent a radio signal. The chime plays the selected ringtone.

Note: The doorbell button (transmitter) can be placed on wood or brick walls without issue. However, never place the button directly onto metal objects or materials containing metal, such as plastic windows or doors that have a metal frame. In such cases, the transmitter will not work properly.

Upkeep and Maintenance

The wireless digital doorbell is a sensitive electronic device. Therefore, it is necessary to observe the following precautions:

- The chime (receiver) is designed for indoor use in dry environments only.

• The chime must be located in an easily accessible location for ease of handling and unplugging.
• Periodically check the functioning of the doorbell button and replace the battery in a timely manner. Use only quality alkaline batteries with the prescribed parameters.
• When the doorbell is not used for a long time, remove the battery from the button and the chime.
• Do not subject the button or chime to excessive vibrations and shocks.
• Do not subject the button or chime to excessive heat and direct sunlight or moisture.
• When cleaning the chime, unplug it from the socket.
• To clean the device, use a slightly moistened cloth with a small amount of detergent; do not use aggressive cleaning agents or solvents.
• This device is not intended for use by persons (including children) whose physical, sensory or mental disability or lack of experience and expertise prevents safe use, unless they are supervised or instructed in the use of the appliance by a person responsible for their safety. It is necessary to supervise children to ensure they do not play with the device.

Do not dispose with domestic waste. Use special collection points for sorted waste. Contact local authorities for information about collection points. If the electronic devices would be disposed on landfill, dangerous substances may reach groundwater and subsequently food chain, where it could affect human health.

Hereby, EMOS spol. s r. o. declares that the radio equipment type P5728T is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.emos.eu/download.

1 – LED dioda zvonku

1 – LED dioda zvonca

2 – prostor za baterije