P5734T - Doorbells Emos - Free user manual and instructions

USER MANUAL P5734T Emos

Designed for wireless doorbell of type P5734 or P5734B.

For proper use of the wireless doorbell, read the instruction manual thoroughly.

Technical Specifications

Transmission range: up to 150 m in an open area (can drop down to one fifth in a busy area)

Button: water resistant; enclosure rating IP56

Pairing the chime with buttons: self-learning function

Pairing capacity: maximum of 8 buttons per 1 chime

Number of ringtones: 10

Transmission frequency: 433.92 MHz, 10 mW e.r.p. max.

Chime power supply: 230 V AC/50 Hz

Button power supply: 1×3 V battery (type CR2032, included)

Includes: double-sided adhesive tape

Chime Description (see fig. 1)

1 - bell LEDs

2 - speaker

3 - volume setting button

4 - ringtone setting button

Button Description (see fig. 2)

1 - ring button

2 - LED

3 - nameplate cover

4 – hole for opening the battery cover

5 - mounting pad

Installing the Button/Removing the Mounting Pad (see fig. 3)

1 - holes for screws

Changing the Button's Battery (see fig. 4)

Pairing the Button with the Chime

1. Plug the chime unit into a 230 V AC/50 Hz socket.
2. Then, long-press the pairing button 📋 on the chime for ca. 5 seconds.
3. The chime LED will light up; release the 📷 button. The chime will switch to self-learning pairing mode which lasts for 25 seconds. During this time, press the ring button. The chime will ring and the button is now paired with the chime. This automatically ends self-learning mode.
4. To pair multiple buttons, repeat the process for each button from step 1.

Note: The chime has an internal memory where it stores the codes of the currently paired buttons for the event of a power failure. There is thus no need to pair buttons again after a power cut.

Wiping the Memory of Paired Buttons

Press and hold the pairing button on the chime.

Plug the chime into a socket.

The LED of the chime will light up after ca. 5 seconds. Release the button. The LED will turn off.

The memory of all paired buttons will be erased.

Installing the Doorbell Button (Transmitter)

1. Begin by pairing the button with the chime.
2. Before installation, check that the pair works reliably in the chosen spot.
3. Remove the mounting pad from the battery cover, see the fig. 3.
4. Use the double-sided adhesive tape (included) or two screws (not included) to fix the back of the mounting pad to the wall. Although the button is weather resistant, choose a location where it is protected, e.g. in a wall recess.
5. Fit the mounting pad back onto the button.
6. Press the button to ring the chime. Pressing is accompanied by LED illumination indicating the button has sent a radio signal. The chime plays the selected ringtone.

Note: The doorbell button (transmitter) can be placed on wood or brick walls without issue. However, never place the button directly onto metal objects or materials containing metal, such as plastic windows or doors that have a metal frame. In such cases, the transmitter will not work properly.

Troubleshooting

The chime does not ring:

• The chime may be out of range.
• Change the distance between the button and the chime; the range may be affected by local conditions.
• The button battery may be drained.
• Replace the battery. Make sure it has the correct polarity.
• Pair the button with the chime again.

The chime is not powered:

- Make sure the chime is properly plugged into the socket and that power is on or the fuse/circuit breaker for the branch is on.

Upkeep and Maintenance

The wireless digital doorchime is a sensitive electronic device. Therefore, it is necessary to observe the following precautions:

- The chime (receiver) is designed for indoor use in dry environments only.

• The chime must be located in an easily accessible location for ease of handling and unplugging.
• Periodically check the functioning of the doorbell button and replace the battery in a timely manner. Use only quality alkaline batteries with the prescribed parameters.
• When the doorchime is not used for a long time, remove the battery from the button.
• Do not subject the button or chime to excessive vibrations and shocks.
• Do not subject the button or chime to excessive heat and direct sunlight or moisture.
• When cleaning the chime, unplug it from the socket.
• To clean the device, use a slightly moistened cloth with a small amount of detergent; do not use aggressive cleaning agents or solvents.
• This device is not intended for use by persons (including children) whose physical, sensory or mental disability or whose lack of experience or knowledge prevents them from using it safely. Such persons should be instructed in how to use the device and should be supervised by a person responsible for their safety. Children must always be supervised to ensure they do not play with the device.

Do not dispose with domestic waste. Use special collection points for sorted waste. Contact local authorities for information about collection points. If the electronic devices would be disposed on landfill, dangerous substances may reach groundwater and subsequently food chain, where it could affect human health.

Hereby, EMOS spol. s r. o. declares that the radio equipment type P5734T is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.emos.eu/download.

1 – LED diody zvonku

2 - reproduktor

Zvanam nav strāvas padeves: