Accessteam DW2460 - Iron ROWENTA - Free user manual and instructions

USER MANUAL Accessteam DW2460 ROWENTA

3. Burst of steam button

DESCRIPCION DE PRODUCTO4 IMPORTANT SAFETY INSTRUCTIONS When using an iron, basic precautions should always be followed, in- cluding the following:

READ ALL INSTRUCTIONS BEFORE USING

• Only use an iron for its intended use.

• To avoid the risk of electric shock, do not immerse the iron in water or other liquids.

• Always turn the iron OFF before plugging or unplugging the iron from the electrical outlet. Never pull on the cord to disconnect the iron from the electrical outlet; instead, grasp the plug and pull on the plug to disconnect the iron.

• Do not let the cord touch hot surfaces. Let the iron cool completely before putting the iron away. Coil the cord loosely around the iron when storing.

• Always disconnect the iron from the electrical outlet before filling the iron with water, emptying the water from the iron, and when the iron is not in use.

• Do not operate the iron with a damaged cord or in the event the iron has been dropped or damaged. To avoid the risk of electric shock, do not disassemble the iron. Take it to a qualified serviceman for exami

nation and repair. Incorrect assembly might result in a risk of electric shock when the iron is used after reassembly.

• Close supervision is required for any appliance used by or near chil

dren. Do not leave the iron unattended while the iron is connected or on an ironing board.

• Burns can occur from touching hot metal parts, hot water, or steam. Use caution when you turn a STEAM IRON upside down – there might be hot water in the reservoir.

• To avoid a circuit overload, do not operate an iron on the same circuit with another high wattage appliance.5

• If an extension cord is absolutely necessary, a cord with an ampere rating equal to or greater than the maximum rating of the iron shall be used. A cord rated for less amperage can result in a risk of fire or electric shock due to overheating. Care shall be taken to arrange the cord so that it cannot be pulled or be tripped over.

• The iron must be used and rested on a stable surface;

• When placing the iron on its stand, ensure that the surface on which the stand is placed is stable;

• The iron must not be left unattended while it is connected to the sup

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of ex

perience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responisible for their safety.

• Children should be supervised to ensure that they do not play with the appliance.

• Cleaning and user maintenance shall not be made by children without supervision.

• The iron is not to be used if it has been dropped, if there are visible signs of damage or if it is leaking.

• Alaways disconect the iron from the electrical outlet, before you leave the room.

SAVE THESE INSTRUCTIONS

WHAT WATER MAY BE USED ? Your iron has been designed to operate using untreated tap water. If in doubt, check with your local water authority. However, if your water is very hard, you can mix 50% untreated tap water with 50% distilled or demineralised water.6 IMPORTANT Heat concentrates the elements contained in water during evaporation.The types of water listed below contain organic waste or mineral elements that can cause spitting, brown staining or premature wear of the appliance: water from tumble dryers, scented or softened water, water from refrigerators, batteries or air conditioners, pure dis

tilled or demineralised water or rain water should not be used in your iron. Also do not use boiling, or bottled mineral water. Before first use: There may be a release of smoke, a harmless odour and a light spray of particles when you use your appliance for the first time. This has no effect on the use of the iron and will disappear quickly. ENVIRONMENT Environment protection first !

Your appliance contains valuable materials which can be recovered or recycled.

Leave it at a local civic waste collection point.7

Set the steam lever on position.

Open the filling inlet door (the iron is unplugged).

Fill in the water tank.

Close the filling inlet door.

Stop filling water when MAX level is reached.

Set the thermostat knob on the desired setting.

The auto off & pilot lights are switched on when the iron is heating up.

Once the pilot light is switched off the iron is ready to be used and steam can be activated.

9. SOLEPLATE CLEANING /

11. CLEANING THE ANTI CALC

VALVE (every 2 weeks) /

Set the thermostat knob on MAX position and the steam lever on

12. SELF CLEANING (every 2 weeks)

PROBLEM POSSIBLE CAUSE SOLUTION

Water drips from the holes in the soleplate. You are using steam while the iron is not hot enough. Wait until the thermostat light goes out. You are using the shot of steam button too often. Wait a few seconds between each use of the button. You have stored the iron horizontally, without emptying it and without setting it to

See the section «Storing your iron». Brown streaks come through the holes in the soleplate and stain the linen. You are using ironing water additives (i.e. scented water, starch). Never use ironing water additives; these will permanently damage your steam iron. You are not using the right type of water. Perform a Self cleaning operation and consult the chapter «What water should I use?». Your linen has not been rinsed sufficiently or you have ironed a new garment before washing it. Make sure that your laundry is rinsed sufficiently in order to remove any deposits of soap or chemical products on new clothes. Your soleplate emits particles. Limescale is starting to build up on your soleplate. Perform a self-clean. The soleplate is dirty or brown and can stain the linen. Your are ironing with an inappropriate temperature selection (temperature too high). Clean the soleplate (refer to chapter 11). Select the appropriate program. You have ironed over a printed are of a garment. Never iron over printed areas or applications – always iron the reverse side of such a garment. There is little or no steam. The water tank is empty. Fill the water tank. Your iron has been used dry for too long. Carry out a Self clean. The soleplate is scratched or damaged. You have placed your iron flat on a metallic rest-plate or ironed over a zip. Refrain from ironing over metallic buttons or zippers. Steam or water come from the iron as you finish filling the tank. The steam control is not set to the

position. Check that the steam control is set to the position. The water tank is overfilled. Never exceed the Max level. The spray does not spray. The water tank is not filled enough. Fill up the water tank.33 Un problème avec votre fer ?

PROBLEMES CAUSES POSSIBLES SOLUTIONS