WT 460 - Alarm clock radio TECHNOLINE - Free user manual and instructions

USER MANUAL WT 460 TECHNOLINE

Your clock radio requires one CR2032 lithium battery (not included) to provide backup power to the clock in the event of a temporary power interruption.

If AC power is interrupted, the LED display will go off and both the radio and the alarm will not function. The backup battery will keep the time and all settings of your unit. Make sure a fresh CR2032 lithium battery is used. A fresh CR2032 battery could backup your clock continuously for around 3 days. SETTING TIME, 12/24HR TIME AND THE SNOOZE DURATION

SET once, the hour digits flash. Press or to set the current hour (hold to advance rapidly).

SET again, the minute digits flash. Press or to set minutes. (hold to advance rapidly). 3. Press SET again, the display shows “24H” and flashes. Press or to select “12H” or “24H” time format. 4. Press SET again, the display shows “05” and flashes. Press or to select your snooze time from 5 to 60 minutes.

SET again or if no key is pressed in approx. 10 seconds to exit the setting mode. Note: when 12-hour time format is selected, the P (PM)LED will appear at the lower middle part of the time display to indicate the afternoon time; there is no AM indicator. Note: Plug the AC/DC power adapter AS0601A-0500600EUL into an AC household outlet and then plug the DC jack into the backside of the clock. Your radio clock is powered now.

1. Place your clock face down on a at surface.

2. Remove the screw from the battery compartment cover. Slide and remove the cover from the

bottom of your clock.

3. Insert one new CR2032 lithium battery into the battery compartment with the + side facing up

4. Slide the cover back on the battery compartment and retighten the screw.EN 2

AL 1.2 once, the A1 LED and the hour digits flash. Press or to set the alarm 1 hour. (hold to advance rapidly).

AL 1.2 again to adjust minutes. Press or to set the alarm 1 minutes. (hold to advance rapidly).

3. Press AL 1.2 again, LED displays “OFF” (alarm off). To select wake to sound sources, press

or to select :- rd = wake-by-radio bu = wake-by-buzzer OFF = alarm off

AL 1.2 again, the A2 LED and the hour digits flash. Press or to set the alarm 2 hour. Repeat step 2) and 3) to set alarm 2.

AL1.2 again or no button is pressed in around 10 seconds to exit alarm setting mode. When wake-by-radio or wake-by-buzzer is selected, the related alarm is turned on, indicated by appearance of the

and / or the A2 LED on the left side of the display. Note: Alarm function can only be operated at AC mode only.

STOP AND RESET THE ALARM TO COME ON THE NEXT DAY When alarm 1 or 2 is sounding, the related A1 or A2 LED flashes. Press the RADIO/ SLEEP or AL

1.2 once to stop the alarm and reset it to come on the following day. After that, A1

A2 icon stays on the display. SNOOZE OPERATION (default snooze duration is 5 minutes) When alarm is sounding, press once, the alarm will be silenced and come on again after the set snooze duration. Note: If your second alarm activates while the first alarm is sounding or it is in the snooze mode, the second alarm overrides the first alarm (the first alarm is reset to come on the next day).

USING THE HI-LO DIMMER

Press to adjust the brightness (HI/ LO/OFF) of the LED display. This can only be done when the radio is off or the unit is not sounding.

SETTING UP THE FM ANTENNA

Extend the FM wire antenna fully and vary the direction for the best FM reception. Do not strip, alter or attach to other antennas.EN 4

RADIO/SLEEP once, the display shows “ON” and then shows the radio frequency readings in Mhz.

to tune the radio to a desired station. Press and hold / to scan for the next clear station.

3. To adjust the volume, press VOL once, the display shows “L07”, press /

to adjust volume from L01 (minimum) to L15 (maximum)

to turn off the radio. Remark: Keep your radio away from fluorescent lamps or other electronic devices, which may cause interference to the radio.

USING THE PRESET MEMORY

This clock radio features 10 preset memories of FM stations. These allow you to preset your favorite stations and access them quickly.

1. Turn on the radio and select a radio station you like to memorize.

2. Press and hold the

SET until MEM LED appears and “01” flashes. Press SET once to store Memory 1.

or to select another station you like to memorize. Then press and hold SET until MEM LED appears and “01” flashes. Press or once, “02” appears. Press SET once to store Memory 02.

4. Repeat Step 2 to 3 to preset memories 3 through 10.

5. To access a preset station at any time, simply press the SET once at a time while the radio

6. To edit a preset station, select another station and then repeat Step 2 to 4. This overrides

the original settings.

USING THE SLEEP TIMER

1. Press the RADIO/SLEEP twice to enter the sleep mode. The

SL (SLEEP) LED and the sleep time “05” (5 minutes) and will flash on the display.

2. P ress the RADIO/SLEEP again as needed to adjust the sleep timer from 5,15, 30, 45, 60, 75,

RADIO/SLEEP twice to show the sleep time remaining.

4. The radio will play for the programmed sleep time and then turn off automatically.

5. To turn off the radio before the sleep time has elapsed, press

once. TROUBLE SHOOTING If your clock displays irrelevant time or does not function properly, which maybe caused by electro- static discharge or other interference, unplug the DC jack to disconnect the AC power (and remove the backup battery). The clock radio will be reset to default settings and you need to set it again. Hereby, Technotrade declares that this product WT460 is in compliance with the essential require- ments and other relevant provisions of Directive 2014/53/EU and ROHS 2011/65/EC. The original EU declaration of conformity may be found at: www.technoline.de/doc/4029665004600EN 4 EN 5 SPECIFICATIONS Alarm duration 1 hour (3-minute on, 9-minute off interval) Snooze duration 5 to 60 minutes Sleep timer selections 5, 15, 30, 45, 60, 75, 90 minutes to OFF Volume L01 (minimum) to L15 (maximum) Preset Memories of radio 10 Default settings:-

Consideration of duty according to the battery law Old batteries do not belong to domestic waste because they could cause damages of health and environment. End-users are committed by law to bring back needed batteries to distributors and other collecting points! Electrical devices have to be disposed separately from the general household waste. Take your old electronics to your local waste collection point or recycling centre. Precautions

• This main unit is intended to be used only indoors.

• Do not subject the unit to excessive force or shock.

• Do not expose the unit to extreme temperatures, direct sunlight, dust or humidity.

• Do not immerse in water.

• Avoid contact with any corrosive materials.

• Do not dispose this unit in a re as it may explode.

• Do not open the inner back case or tamper with any components of this unit. Batteries safety warnings

• Use only alkaline batteries, not rechargeable batteries.

• Install batteries correctly by matching the polarities (+/-).

• Always replace a complete set of batteries.

• Never mix used and new batteries.

• Remove exhausted batteries immediately.

• Remove batteries when not in use.

• Do not recharge and do not dispose of batteries in re as the batteries may explode.

• Ensure batteries are stored away from metal objects as contact may cause a short circuit.

• Avoid exposing batteries to extreme temperature or humidity or direct sunlight.

30, 45, 60, 75, 90 u OFF.