NT 702 Tc - Vacuum Cleaner Kärcher - Free user manual and instructions

USER MANUAL NT 702 Tc Kärcher

H05VV-F 2x1,5 H05VV-F 2x1,5 Teilenummer (EU) 6.647-069.0 6.647-069.0 Kabellänge m 10 10English 9 Contents General notes Read these original instructions and the enclosed safety instructions before us- ing the device for the first time. Act in ac- cordance with them. Keep both books for future reference or for future own- ers. If the operating instructions and safety instructions are not observed, the device can be damaged and dangers could arise for users and other persons. Notify the dealer immediately in the case of shipping damage. Check the package contents when unpacking for missing accessories or for damage. Environmental protection The packing materials can be recycled. Please dispose of packaging in accordance with the en- vironmental regulations. Electrical and electronic appliances contain valu- able, recyclable materials and often components such as batteries, rechargeable batteries or oil, which - if handled or disposed of incorrectly - can pose a potential threat to human health and the environ- ment. However, these components are required for the correct operation of the appliance. Appliances marked by this symbol are not allowed to be disposed of togeth- er with the household rubbish. Notes on the content materials (REACH) Current information on content materials can be found at: www.kaercher.com/REACH Intended use 몇 WARNING Health risk Inhalation of dusts that are harmful to health Do not use the device for vacuuming up dusts that are harmful to health. This vacuum cleaner is intended for the wet and dry cleaning of floor and wall surfaces. This device is suitable for commercial and industrial use, e.g. in workshops, industrial plants, schools and hotels. The room temperature must not exceed 40 °C. The device must weigh a maximum of 100 kg with load. Description of the device Illustration A 1 Knurled handle screw 2 Cartridge filter 3 Mechanical overflow protection 4 Removing the 5 Suction hose 6 Push handle 7 Cable hooks 8 Suction head lock 9 Dirt receptacle 10 Tilting chassis 11 Container handle 12 Steering roller 13 Suction hose port 14 Floor nozzle 15 Suction pipe 16 Carrying handle 17 Angle piece 18 Suction turbine power switch 2 19 Suction turbine power switch 1 20 Suction turbine power switch 3 21 Rest for floor nozzle 22 Drain hose 23 Suction pipe holder 24 Holder for crevice nozzle 25 Mains cable 26 Type plate Preparation

1. Unpack the device and install the accessories.

• Illustration B Initial startup Power connection ATTENTION Exceeding the grid impedance Electrical shock in the event of a short-circuit The maximum permissible mains grid impedance at the electrical connection point (see Technical data) must not be exceeded. Contact your electricity supplier in the case of any un- certainties regarding the mains grid impedance at your electrical connection point. Dry vacuuming ATTENTION Danger due to fine dust entering Risk of damage to the suction motor. Never remove the cartridge filter when vacuuming. An additional paper filter bag (special accessories) can be used when vacuuming fine dust. General notes p. 9
• Environmental protection p. 9
• Intended use p. 9
• Description of the device p. 9
• Preparation p. 9
• Initial startup p. 9
• Operation p. 10
• Transport p. 10
• Storage p. 10
• Care and service p. 10
• Troubleshooting guide p. 11
• Warranty p. 11
• Accessories and spare parts p. 11
• EU Declaration of Conformity p. 11
• Technical data English Installing the paper filter bag p. 1210

1. Unlock and remove the suction head.

2. Connect the paper filter bag (special accessories).

3. Fit and lock the suction head.

Wet vacuum cleaning Installing the squeegees

1. Remove the brush strip.

Removing the paper filter bag The paper filter bag (special accessories) must al- ways be removed when vacuuming wet substances. It is recommended to use a special filter bag (wet) (see filter systems). Wet vacuum cleaning with cartridge filter ATTENTION Danger due to water outlet Risk of damage to the suction motor. Never remove the cartridge filter when vacuuming. On completion of wet vacuum cleaning: Clean the machine overflow protection container with a moist cloth and dry them off. When changing from a wet to a dry vacuum cleaner, replace the wet cartridge filter with a dry one. Wet vacuum cleaning with wet filter

1. Unlock and remove the suction head.

2. Unscrew the knurled handle screw and pull off the

3. Screw the knurled handle screw tight.

4. Install the wet filter (special accessories).

5. Fit and lock the suction head.

ATTENTION Danger due to water outlet Risk of damage to the suction motor. Never remove the wet filter when vacuuming. On completion of wet vacuum cleaning: Clean the machine overflow protection container with a moist cloth and dry them off. When changing from a wet to a dry vacuum cleaner, replace the wet cartridge filter with a dry one. Draining the waste water 몇 WARNING Improper disposal of waste water Environmental pollution Observe the local waste water treatment regulations.

1. Drain the waste water via the drain hose.

Device with a metal container: Illustration F Device with a plastic container: Illustration G Draining the container completely

1. Lock parking brake.

2. Hold the container by the handle and tilt it by lifting.

3. Completely drain the container.

4. Tilt the container back into its original position.

5. Release the parking brake.

Clip connection The suction hose is equipped with a clip system. All ac- cessory parts with a nominal width of 40 mm can be connected. Illustration I Operation Switching on the device

1. Connect the mains plug.

2. Switch on the device.

Draining the dirt receptacle The suction duct is equipped with a float. When the maximum permissible waste water level in the container is reached, the suction volume is in- terrupted.

1. Switch off the device.

2. Empty the container.

Switching off the device

1. Switch off the device.

2. Vacuum off the inside and outside of the device and

clean with a moist cloth. Storing the device

1. Roll up the suction hose and hang it over the push

2. Store the device in a dry room and secure it against

unauthorised use. Transport 몇 CAUTION Failure to observe the weight Risk of injury and damage Be aware of the weight of the device during transportation.

1. Remove the suction hose with floor nozzle from the

support. Carry the device by the carrying handle and the suction pipe, not by the push handle.

2. Pull the device behind you via the push handle for

transporting over longer distances.

3. When transporting the device in vehicles, secure it

to prevent it from slipping or overturning in accord- ance with the respective valid guidelines. Storage 몇 CAUTION Failure to observe the weight Risk of injury and damage Be aware of the weight of the device during storage. The device may only be operated indoors. Care and service DANGER Danger of electric shock Injuries due to touching live parts Switch off the device. Remove the mains plug. Changing the cartridge filter

1. Unlock and remove the suction head.

2. Unscrew knurled handle screw, remove cartridge fil-

ter and replace with a new one.

3. Screw the knurled handle screw tight.

4. Fit and lock the suction head.English 11

Cleaning the mechanical overflow protection

1. Unlock and remove the suction head.

2. Unscrew the knurled handle screw and pull off the

3. Clean the mechanical overflow protection with a

4. Connect the cartridge filter.

5. Screw the knurled handle screw tight.

6. Fit and lock the suction head.

Troubleshooting guide DANGER Danger of electric shock Injuries due to touching live parts Switch off the device. Remove the mains plug. Suction turbine does not start up

1. Check the socket and the power supply fuse.

2. Check the mains cable, mains plug and mechanical

overflow protection on the device.

3. Switch on the device.

Suction power decreases

1. Remove any blockages from the suction nozzle,

suction pipe, suction hose or cartridge filter.

2. Renew the sealing ring between the suction head

3. Change the filled paper filter bag (special accesso-

5. Check the drain hose for leaks.

Escaping dust when vacuuming

1. Check that the cartridge filter is correctly fitted.

2. Change the cartridge filter.

Mechanical overflow protection (wet vacuum clean- ing) does not work

1. Check the float for ease of movement, clean or re-

place with a damp cloth if necessary. Customer Service department If the malfunction cannot be corrected, the device must be checked by the Customer Service department. Warranty The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possi- ble malfunctions on your appliance within the warranty period free of cost, provided that a material or manufac- turing defect is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorised customer service site. (See overleaf for the address) Accessories and spare parts Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely. Information on accessories and spare parts can be found at www.kaercher.com. EU Declaration of Conformity We hereby declare that the machine described below complies with the relevant basic safety and health re- quirements in the EU Directives, both in its basic design and construction as well as in the version placed in cir- culation by us. This declaration is invalidated by any changes made to the machine that are not approved by us. Product: Wet/dry vacuum cleaner Type: 1.667-xxx Currently applicable EU Directives 2006/42/EC (+2009/127/EC) 2011/65/EU 2014/30/EU Harmonised standards used EN 50581 EN 55014-1: 2017 EN 55014-2: 2015 EN 60335-1 EN 60335-2-69 EN 61000-3-2: 2014 EN 61000-3-3: 2013 EN 62233: 2008 National standards used

Støvutslipp under suging