CM001B - Microphone Auna - Free user manual and instructions

Product type	Condenser microphone
Brand	Auna
Model	CM001B
Article number	10011705
Diaphragm diameter	32 mm
Built-in high-pass filter	-6 dB at 100 Hz (switchable)
Polar pattern	Cardioid
Frequency response	20 Hz - 20 kHz
Sensitivity	36 dB ± 2 dB
Output impedance	200 ohms
Maximum sound level (0.5% THD)	125 dB
Connector	XLR (3-pin)
Power supply	48V phantom (via XLR)
Dimensions (diameter × height)	5 × 15 cm
Weight	Approximately 340 g
Package contents	Microphone, shock mount, windscreen, 3/8" to 5/8" adapter, carrying case, user manual
Warranty	2 years (subject to proper use)
Cleaning	Dry cloth only
Manufacturer	Chal-Tec GmbH, Wallstraße 16, 10179 Berlin, Germany

Frequently Asked Questions - CM001B Auna

How to connect the CM001B microphone?

Connect the microphone to a mixing console or recording device using a quality XLR cable. Then activate the 48V phantom power on your equipment. Ensure the volume settings are at minimum before activating the power.

Can I use this microphone without phantom power?

No, the condenser microphone requires 48V phantom power via the XLR cable to operate. Without it, no sound will be produced.

How to activate the high-pass filter (Low Cut)?

Unscrew the cap under the microphone, then disassemble the tubes of the shell. Press the blue switch on the circuit board to activate or deactivate the 100 Hz high-pass filter.

What polar pattern does this microphone have?

The CM001B has a cardioid polar pattern, ideal for capturing frontal sounds while reducing lateral and rear noise.

What does the delivery of the Auna CM001B microphone include?

The delivery includes the microphone, a spider (shock mount), a windscreen, a 3/8" to 5/8" adapter, a carrying case, and the user manual.

How to clean the microphone?

Use a dry, soft cloth. Do not use volatile liquids or insecticide sprays. Avoid prolonged contact with rubber or plastic.

What is the warranty of this microphone?

The legal warranty is 2 years from the date of purchase, subject to proper use and compliance with instructions.

Can I mount the microphone on a standard stand?

Yes, the included adapter (3/8" to 5/8") allows mounting on most microphone stands. You can also screw it directly without an adapter if your stand is compatible.

What accessories are recommended to improve sound quality?

A pop filter (not included) is recommended to reduce plosive sounds and protect from moisture. Always use a quality XLR cable and the spider mount to avoid vibrations.

How to dispose of this product at end of life?

Do not dispose of the device with household waste. Take it to a collection point for recycling of electrical and electronic equipment in accordance with local regulations.

USER MANUAL CM001B Auna

TECHNISCHE DATEN

Member of Berlin Brands Group

Handwerkerstr. 11

15366 Dahlwitz-Hoppegarten

Deutschland

Symbol of a trash bin with crossed lines and a horizontal bar below (no text or labels)

Berlin Brands Group UK Ltd

PO Box 1145

Oxford, OX1 9UW

United Kingdom

Congratulations on purchasing this device. Please read the following instructions carefully and follow them to prevent possible damages. We assume no liability for damage caused by disregard of the instructions and improper use. Scan the QR code to get access to the latest user manual and more product information.

TECHNICAL DATA

Item number 10011705
Type Condenser microphone, 32mm membrane integrated -6dB 100 Hz low-cut filter
Pattern Cardioid
Frequency range 20 Hz - 20 KHz
Sensitivity 36dB-+ / - 2 dB
Output impedance 200 ohms
max. gain 125 dB für 0,5% THD
Connection and power supply XLR	48V phantom power
Dimension & weight 5 x 15 cm (∅xH), ca. 340 g

Scope of delivery

• Microphone,
• Shockmount
• Adapter (3/8" to 5/8"),
• Protective case,
• Manual

SAFETY INSTRUCTIONS

• These operating instructions are intended to familiarize you with the operation of this product.
• Please keep this manual in a safe place so that you can access it at any time.
• Please use the product only in its intended manner. Any other use may result in damage to the product or to the environment of the product.
• Conversion or modification of the product impairs product safety.
• Never open the product on your own authority and never carry out repairs yourself!
• Handle the product carefully. It can be damaged by shocks, blows or falling from an already low height.
• Keep the product away from moisture and extreme heat.
• Do not drop metal objects into this product.
• Do not place heavy objects on this product.
• Clean the product only with a dry cloth.
• Only use accessories recommended by the manufacturer or by qualified retailers.
• Warranty will be void if the unit is tampered with.

Small objects

Keep small objects (i.e. screws, mounting material, memory cards etc.) and packaging out of the range of children. Do not let children play with foil. Choking hazard!

Transporting the device

Please keep the original packaging. To gain sufficient protection of the device while shipment or transportation, make sure to put it back in its original packaging.

Cleaning the surface

Do not use any volatile liquids, detergents or the like. Use a clean dry cloth.

MOUNTING AND OPERATION

To get the sound you want, try changing the mic position relative to the sound source oreven move the microphone around in the recording room of your studio. Adjusting the angle at which walls face the sound source can also be helpful.

There is an adapter on your microphone that lets you mount it on mic stands with either metric (Europe) or imperial-gauge threads (North America).

Basically, the microphone in the stand mount adapter should stand upright and face the sound source at a right angle. Of course, you can detach the microphone from the stand mount adapter and attach it to a commercially available suspension mount.

The angle of the microphone to the sound source influences the sound of the recording; therefore, experiment with different positions until you achieve the desired sound. To this end, you can rotate the mic in the stand mount adapter by loosening the screw somewhat and tightening it again. If necessary, you can bend the microphone out of its vertical position by using the hinge on the microphone stand.

It is often advisable to use a pop filter (not included) when recording vocals, not only to ovoid overly accentuated 'S, 'P' and 'B'sounds, but also to protect the mic from moisture. it is always a good idea to store the microphone in its protection bag when not in use.

Connect the microphone to a mixer or recording device with a high quality XLR cable before turning on the phantom power. Make sure all volume and gain controls on your mixer, mic preamp or recording device are at their minimum volume settings when switching the phantom power on. Once the MCOO1 is plugged in and the phantom power is switched on, Move the channel fader gradually to the 0dB position adjust the input gain using your channel peak led or VU-meter.

NOTE: Please make sure to handle the microphone shaft with attention and care to avoid damaging the screw thread. In no situation should you ever apply excessive force.

Low Cut Filter: To operate the low cut switch, unscrew the bottom of the microphone housing, slide the microphone body from the chassis.

Look for the blue switch in the middle of the microphone circuit board. Pressing the swith activates the low cut filter.

DISPOSAL CONSIDERATIONS

Symbol of a trash bin with crossed lines and a horizontal bar below (no text or labels)

If there is a legal regulation for the disposal of electrical and electronic devices in your country, this symbol on the product or on the packaging indicates that this product must not be disposed of with household waste. Instead, it must be taken to a collection point for the recycling of electrical and electronic equipment. By disposing of it in accordance with the rules, you are protecting the environment and the health of your fellow human beings from negative consequences. For information about the recycling and disposal of this product, please contact your local authority or your household waste disposal service.

MANUFACTURER & IMPORTER (UK)

Manufacturer:

Chal-Tec GmbH, Wallstrasse 16, 10179 Berlin, Germany.

Importer for Great Britain:

Berlin Brands Group UK Ltd PO Box 1145 Oxford, OX1 9UW United Kingdom

Hereby, Chal-Tec GmbH declares that the radio equipment type CM001B is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: use.berlin/10011705

For Great Britain: Hereby, Chal-Tec GmbH declares that the radio equipment type CM001B is in compliance with the relevant statutory requirements. The full text of the declaration of conformity is available at the following internet address: use.berlin/10011705

Chère cliente, cher client,

FICHE TECHNIQUE

Symbol of a trash bin with crossed lines indicating no waste or discharge, and a solid black rectangle below (no text or labels)

Berlin Brands Group UK Ltd

PO Box 1145

Oxford, OX1 9UW

United Kingdom

DATI TECNICI

Symbol of a trash bin with crossed lines and a horizontal bar below (no text or labels)

Berlin Brands Group UK Ltd

PO Box 1145

Oxford, OX1 9UW

United Kingdom

DATOS TÉCNICOS

Symbol of a trash bin crossed with a diagonal line and a horizontal bar below (no text or labels)

Berlin Brands Group UK Ltd

PO Box 1145

Oxford, OX1 9UW

United Kingdom

Abstract white logo design on dark background, resembling stylized letter 'S' or wave form (no text or symbols)