USER MANUAL GDH 330 Güde
ENGLISH Please read the instructions carefully before starting the machine.
GB Cleaning / Maintenance
F Nettoyage/Entretien
Surfacer and thicknesser GDH 330
Art No 55268
Service connection. 230V 50Hz
Max.Power 1500W
Max.,feed speed. 7,4 m/min
Idle speed. 8500 min-1
Max. plane thickness 330 mm
Plane thickness 152 mm
Chip removal Thicknessing. 0,8 mm
Blade Number. 2
Size Surfacer bench. 330 x 630 mm
Weight. 30 kg
Degree of protection . IP 20
Noise details
Uncertainty K = 4 dB
ldling:
Sound pressure level L * 93,9 dB (A) PA
Sound power level L_WA^* 109,45 dB (A)
Thicknessing:
Sound pressure level L PA 97,9 dB (A)
Sound power level L_WA^* 111,29 dB (A)
Wear ear protectors!
- Measured according to EN ISO 3746 + 11202
The values stated are emission values and as such do not necessarily constitute values which are safe for the workplace. Al- though there is a correlation between emission levels and environmental impact levels, whether further precautions are necs- sary cannot be derived from this. Factors influencing the actually present environmental impact level in the workplace include the characteristics of the work area and other noise sources, i.e. the number of machines and other neighbouring work process- es. The permitted workplace values can likewise vary from country to country. This information is intended to assist the user in estimating hazards and risks.
Read and understand the operating instructions before using the appliance. Familiarise with the
control elements and how to use the appliance properly. Abide by all the safety measures stated in the service manual. Act responsibly toward third parties.
The operator is responsible for accidents or risks to third parties.
In case of any doubts about connection and operation refer please to our customer center
Specified Conditions Of Use
The surfacer and thicknesser is only designed for DIY and hobby use.
The wooden materials must be free of foreign substances (nails, other metal parts, cables, ropes, cords and the like).
The protective equipment on the appliance is strictly prohibited to be disassembled, changed, used in conflict with the designation and it is prohibited to attach any protective equipment of other manufacturers.
The bridge guard must not be removed during machining. The unused part of the blade shaft must be covered.
Not observing general regulations in force and instructions from this manual does not make the manufacturer liable for damages.
The current accident prevention rules and regulations must be obeyed.
Requirements for operating staff
The appliance may only be operated and maintained by persons familiarised with it and informed about possible risks.
Never let children work with the appliance. Never let adults work with the appliance unless they have been properly trained.
The operating staff must carefully read the Operating Instructions before using the appliance.
Qualification: Apart from the detailed instructions by a professional, no special qualification is necessary for appliance using.
Minimum age: Persons over 18 years of age can only work on the appliance. An exception includes youngsters trained in order to reach knowledge under supervision of the trainer during occupational education.
Local regulations may stipulate the minimum age of the user.
Training: Using the appliance only requires corresponding training by a professional or the Operating Instructions. No special training is necessary.
Residual risks
Even when the device is used properly and all safety regulations are complied with, there still may be some residual risks.
Danger of injury!
of fingers and hands by contact with the blade shaft at uncovered areas when changing tools. These can also be crushed by opening the guard.
- on the infeed and discharge opening
- by dangerous recoil
- Danger from current if the electric cables have not been connected correctly.
- harmful wood duct may be generated if operated without an extractor or chip bag.
- by catapulted parts
- Metal parts in the workpiece can blunt or destroy the blades.
Hearing damage
A longer stay in the immediate vicinity of the running unit may cause hearing damage. Wear ear protectors!
Despite the observance of the operating instructions there still may be some hidden residual risks.
Emergency procedure
Conduct a first-aid procedure adequate to the injury and summon qualified medical attendance as quickly as possible. Protect the injured person from further harm and calm them down. For the sake of eventual accident, in accordance with DIN 13157, a workplace has to be fitted with a first-aid kit. It is essential to replace any used material in the first-aid kit immediately after it has been used. If you seek help, state the following pieces of information:
- Accident site
- Accident type
- Number of injured persons
- Injury type(s)
Symbols
Read the Operating Instructions
Unplug the machine before any work on it.
Safety gloves to be used!
Wear a respirator!
Wear eye protective goggles! Wear ear protectors!
Safety shoes to be used
Warning/caution!
Warning against dangerous electric voltage
Caution! Danger of injury from planing blades.
Warning against thrown-off items
Remove all undesirable items, e.g. nails and wire, before working
Do not reach into the danger area of the moving blades.
Always keep children and unauthorised persons out of reach of the appliance.
Do not expose the appliance to rain and do not use it in wet or moisture conditions.
CE marking
Any damaged or disposed electric or electronic devices must be delivered to appropriate collection centres. Batteries, oil, and similar substances must not enter the environment.
Protect against humidity
This side up
Safety Instructions
WARNING
Read all safety warnings and all instructions, including those given in the accompanying brochure.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.
Caution! The machine must be secured to the door or using suitable screws since otherwise there is a risk that it will tip over.
Switch the engine off and unplug it if you are not working with the appliance or when leaving the appliance or adjusting, maintaining or repairing it.
When being operated, the machine must stand on a horizontal and flat surface and the floor around the machine must be flat, well-maintained and with no waste, such as sawdust and cuttings.
Errors in the machine, including the guard or the blade shafts, must be reported to the person responsible for safety as soon as they are discovered.
Familiarise yourself with the safe procedures for cleaning, maintaining and regularly removing chips and dust to reduce the fire risk.
Electrical connection / Electrical safety
WARNING! Electric shock! There is a risk of injury caused by electric shock!
Defective cable or plug may cause electric shock.
Avoid body contact with earth parts to protect yourself from electric shocks.
Operation is only allowed with a safety pitch against stray current (RCD max. stray current of 30mA ).
Insert the plug of the electrical cable in a socket of suitable shape, voltage and frequency complying with current regulations.
Do not pull the service cable to pull the plug out of socket.
When routing the connecting cable ensure that it cannot cause interference and cannot be crushed, kinked or wet.
Work preparation / operation
Provide adequate lighting or good lighting conditions when working with the machine.
Before each use, check the following:
- Proper function of the on and off button, incl. the emergency switch.
- Locked disconnected protective equipment by gradual opening of every separating protective equipment to be able to turn the machine off and checking that the machine cannot be turned on whenever the protective equipment is open.
- Brake
by means of a function test to establish whether the braking process takes place within the specified braking time and, if the machine is fitted with a mechanical brake, that the brake must be tested each time the overload guard is tripped.
- Recoil risk
at least once per shift by a visual inspection to establish that they are in good working order, for example, that the contact surface has not been damaged by impacts and that the grabs fall back without hindrance due to their own weight.
- Planing blades
for signs of damage and to ensure they are positioned correctly.
The machine may only be used if all these conditions are satisfied.
Use pusher wood or sticks which are in perfect condition for machining short workpieces.
Connect the machine to a dust and chip extractor.
required air volume approx. 700 - 1000m^3 /h
Vacuum at every extractor connection port: 840 PA
Cross-section of the connection port: 100mm
Check that the stop is secure before starting the machining work.
Ensure that you can maintain your balance at all times. Stand to the side of the machine. Whilst the machine is running keep your hands at a safe distance from the cutting roller and from the point at which the chips are discharged.
Do not start the planing work until the cutting roller has reached the required speed.
Only plane with sharp blades and never plane over metal (nails and screws).
Also ensure that the workpiece does not contain any cables, wires, cords or the like. Do not machine any wood which has lots of knots or knot holes.
Secure long workpieces to prevent them tipping over at the end of the planing process. Use roller stands, for example, or similar devices for this purpose.
Removing sawdust and chippings from the machine when running is strictly prohibited.
Switch off the machine immediately it is jams. Pull out the mains plug and remove the jammed workpiece.
Set the smallest cutting size after use to prevent the risk of injury.
Machine to be stored in locked spaces, out of reach of children.
Maintenance
Unplug the machine before any work on it.
Prior to every use, visually check the machine to rule out any defects, in particular on the power cable and the plug.
The machine must not be used under any circumstances if the machine or the safety devices are damaged.
Repairs and works specified in these Instructions may only be performed by qualified authorised staff.
Use only original accessories and original spare parts. At all times, keep the machine, ventilation slots, in particular, clean. The sawdust ejection and/or dust exhauster should be cleaned at regular intervals. Never spray water on the machine!
Only a regularly maintained and treated appliance can serve as a satisfactory aid. Insufficient maintenance and care can lead to unforeseen accidents and injuries.
Never clean the machine and its components with solvents, flammable or toxic liquids. Us only a damp cloth making.
Apply environment-friendly oil to all moving parts.
If necessary, a list of spare parts can be found at www.guede.com.
Disposal
Any damaged or disposed devices must be delivered to appropriate collection centres.
Transport packaging disposal
The packaging protects the machine against damage during transport. Packaging materials are usually chosen based on environment aspects and waste treatment principles and are therefore recyclable. Returning the packaging into material circulation saves raw materials and reduces waste production. Parts of packagings (e.g. foils, styropor) can be dangerous for children.
Risk of suffocation!
Keep parts of the packagings out of reach of children and dispose them as soon as possible.
Guarantee
Warranty period of 12 months applies to commercial use and 24 months applies to private use and commences on the day of purchase of the device.
The guarantee solely covers inadequacies caused by material defect or manufacturing defect. Original payment voucher with the sales date needs to be submitted for any claim in the guarantee period.
The guarantee does not cover any unauthorised use such as appliance overloading, use of violence, damage as a result of any unauthorised interference or caused by foreign items. Failing to follow the operating and assembly instructions and common wear are also not included in the guarantee.
Please be sure to know that returning the product in or after the warranty period must be made in the original packaging.
Serial No.:
Art.No:
Year of production:
Tel.: +49 (0) 79 04 / 700-360
Fax: +49 (0) 79 04 / 700-51999
E-Mail: support@ts.guide.com
Service
Do you have any technical questions? Any claim? Do you need any spare parts or operating instructions? We will quickly help you and without needles bureaucracy at our web pages at www.guide.com in the Servicing part. Please help us be able to help you. In order to identify your device in case of claim we need the serial No., product No. and year of production. All this data can be found on the type label. Please enter it here for future reference:
Inspection and maintenance plan
| Regular servicing period Before any | start-up | If necessary Once a week | After 6 months |
| Check that the planing blade is in perfect condition | Inspection | ✓ | | |
| Change | | ✓ | ✓ |
| Check the function of the safety equipment | Inspection | ✓ | | |
| Change | | ✓ | |
| Clean dust and chips off the machine | Clean | ✓ | | |
| Check the drive belt to ensure it has the correct tension and is in good condition or not worn | Inspection | | ✓ | |
| Change | | | |
| Oil or grease all moving connecting parts | | | ✓ |
Failure removal
Before rectifying a fault on the machine, switch off the machine and pull out the mains plug.
| Failures | Causes | Removal |
| Machine does not work or stops suddenly | ·Power cut
·Motor or switch defective
·Check microswitch | ·Check fuse, check overload switch on machine.
·Have the motor or switch checked by an electrician.
·Fit the chip extractor hood so that the microswitch is pressed.→2 |
| Machine stops during planing | ·Planing blade blunt/worn
·Overload switch has tripped
·Check microswitch | ·Replace or sharpen blade
·Switch on the motor again once it has cooled
·Fit the chip extractor hood or bench lock so that the microswitch is pressed.→2 |
| Workpiece jams during thicknessing | ·Cutting depth too great · Reduce cutting | depth and machine
the workpiece in several passes |
| Unsatisfactory surface finish | ·Planing blade blunt/worn
·Planing blade filled with chips
·Uneven feed | ·Replace or sharpen blade
·Remove chips
·Feed the workpiece with constant pressure and at reduced speed |
| Machined surface too rough | ·Workpiece contains too much moisture | ·Dry workpiece |
| Machined surface cracked | ·Workpiece was machined against the grain
·Too much material planed at one pass | ·Machine the workpiece from the opposite direction
·Machine the workpiece in several passes |
| Workpiece speed too low during thicknessing | ·Workpiece was machined against the grain
·Too much material planed at one pass | ·Clean bench top and apply a thin coating of lubricant wax
·Repair transport rollers
·Set the lever for the thicknessing setting to the top position |
Enable and check all safety equipment after all troubleshootinging work.
\section*{Caracteristiques Techniques}
We, hereby declare the conception and construction of the below mentioned appliances correspond - at the type of construction being launched - to appropriate basic safety and hygienic requirements of EC Directives.
In case of any change to the appliance not discussed with us the Declaration expires.
90431 Nurnberg Germany
Type Ex.Cert.-No.:
97/68/EC &2016/1628/EU
Emission No.:
2000/14/EC_2005/88/EC
