EG311UXUU - Range hood Atag - Free user manual and instructions

USER MANUAL EG311UXUU Atag

instructions for use/installation instructions

WS90..MM - WS12..MM - ES12..MM Waal

WS90..NM - WS12..NM - ES12..NM Dinkel

nederlandblzNILJB

english page GB 1 G E 17 IE

Motor of bediening defect.

The extractor hood has been designed for domestic use and for the purposes stated. Atag extractor hoods are available in many different models, which fit elegantly into all interiors. The Atag range offers various types of hoods, some with built-in motors and others suitable for recirculation.

When you have read this manual, you will quickly be aware of all the facilities the appliance can offer you. You can read about safety and how you should look after the appliance. In addition you will find environmental tips and instructions that can help to save energy.

Keep the manual. Any later user of this appliance could benefit from them.

table of contentsintroduction

general 1-2

introduction 1

for your safety 2

instructions for use 3-7

lighting 3

fan 3-5

carbon filter indicator 6

switch off the key signal 6

faults 7

how to keep the appliance looking good 8-9

installation instructions 10-17

installation 10-12

assembly 13-16

technical data 17

disposal of packaging and appliances 17

Please note!

Separate installation instructions are supplied for the Island models.

for your safety

please note

This appliance should be connected by a registered fitter. Damage arising from incorrect connection or incorrect fitting is not covered by the guarantee.

Disconnect the appliance before starting with cleaning or reparation. It is recommended that you do this by removing the plug from the socket or by setting the isolation switch to zero.

Never flame under an extractor. The high flames can cause fire. Even if the ventilator is switched off.

When deep-frying, always keep a close watch.

If the appliance is used together with equipment which uses gas or other fuels, then a sufficient supply of fresh air must be ensured.

Switch the extractor hood on before starting to cook. After cooking, allow the extractor hood to continue to run for approx. 10 minutes. This can also be done automatically (see 'automatic continued operation').

Clean the appliance regularly, as shown in 'maintenance'. This minimises the chance of a fire starting.

Switch off the electricity before replacing the light bulbs! Only use the same sort of light bulbs with the same Wattage.

In view of possible sharp edges on the chimney we advise you to wear working gloves when fitting the chimney.

control panel

The LEDs on the control panel light up green in order to show the programmed setting. The LEDs light red in order to indicate that the fat filters must be cleaned (see page 9 "cleaning fat filters") or the carbon filters (optional) must be changed (see page 9 "replacing carbon filters").

lighting

switching lighting on and off

Briefly press the lighting button

The lighting comes on at its highest setting.

Press the key once again and keep it pressed in order to set the intensity of the lighting. The lighting changes from the brightest to dimmest setting and vice versa, for as long as you keep the key pressed.

Press the button for a third time and the lighting goes out.

fan

Press the button + on

The extractor hood comes on at setting 1. The green LEDs on the control panel indicate the programmed settings.

adjusting the extractor capacity

Press the button to select a higher or lower setting.

fan (continued)

intensive setting

Press button for a minimum of 2 seconds.

The extractor hood switches to its highest setting for 10 minutes (setting 4). In the control panel the 4^ green LED flashes.

After 10 minutes the extractor hood switches back to the original setting.

Repeatedly press the key all green LEDs in the control panel are off or press key for at least 2 seconds in order to switch off the extractor hood.

automatic continued operation

Choose the fan setting desired and press button · 12

The extractor hood remains at the selected setting for 10 minutes, after which the extractor hood is automatically switched off.

If the lighting was switched on during the automatic continued running, it will remain switched on. The lighting will be automatically dimmed to 30 - 40% of the maximum light strength.

Clean Air function

You can use the Clean Air function to regularly freshen the air in your residence.

During the Clean Air function, every hour the extractor hood operates for 10 minutes on setting 1. It then remains switched off for 50 minutes. This cycle repeats for 12 hours.

fan (continued)

Press button for about 4 seconds to switch on the Clean Air function. The 4^th green LED in the operational panel flashes for as long as setting 1 is switched on (duration 10 minutes). The 4^th green LED is permanently lit in the switched off phase (duration 50 minutes).

After 12 hours the Clean Air function is automatically switched off. Press button for about 4 seconds to switch off the Clean Air function after a shorter period.

Attention: if you switch on the extractor hood during use of the Clean Air function, the Clean Air function will be cancelled and the extractor hood will continue to operate on the programmed setting.

grease filter indicator

If the 1^st red LED in the control panel starts to flash, clean the filter immediately.

Replace the cleaned filter and erase the electronic memory by pressing the button for approx. 5 seconds. The 1st red LED stops flashing.

carbon filter indicator (optional)

switching on the carbon filter indicator

If you use the recirculation extractor hood, you must use a carbon filter. In that case, you can switch on the carbon filter indicator. Press keys for approx. 5 seconds in order to switch on the carbon filter indicator. The 4 green LEDs light up and the extractor hood gives an audible signal.

replacing the carbon filter

If the 2^nd red LED in the control panel starts to flash, clean the filter immediately. Place a new carbon filter and erase the electronic memory by pressing the button for approx. 5 seconds. The 2^nd red LED stops flashing.

switching off the carbon filter indicator

Press keys and for approx 5 seconds in order to switch off the carbon filter indicator. The 4 green LEDs light up and the extractor hood gives an audible signal.

You can check if the carbon filter is switched on by pressing the keys and continuously for approx 5 seconds. When the carbon filter indicator is switched on the 4 green LEDs light up, otherwise the 4 red.

switch off the key signal

As you press a key, a key signal sounds in confirmation. Press keys on for 3 seconds continuously on the in order to switch on the key signal.

Repeat this procedure if you wish to switch off the key signal again.

faults

Please check the following points which may solve the problem, before calling the service department.

If the connection cable is damaged, it should be replaced by the service department of the manufacturer or similarly qualified persons in order to prevent dangerous situations from arising.

NB: Disconnect the appliance from the mains before starting any repairs, preferably by removing the plug from the socket or by setting the isolation switch to zero.

fault

Lighting does not work.

cause

Lamp defective.

solution

NB:

Only use the same type of lamp with the wattage stated.

Change the light bulb.
Gently press the front side of the window (1) and it should tilt open slightly (2).
- Open the window fully and fit a new 20 W halogen bulb. Note: do not touch the bulb's glass with your fingers.
Gently push the window closed again.

Extractor hood makes a lot of noise.

Discharge duct too long or has too many bends.

Change the discharge duct (see installation instructions).

No extraction.

Motor defective.

Phone the Service department.

Motor or controls defective.

Phone the Service department.

Connection lead defective.

Phone the Service department.

extractor hood

Clean the grease filters as soon as the grease filter indicator light comes on.

The stainless steel on the outside of the hood can be cleaned with soapy water and a damp cloth. The stainless steel will regain its shine if you occasionally use a stainless steel care product or polish. The polish imparts a dirt-resistant layer to the stainless steel. Always clean the stainless steel in the direction of polishing.

Never use abrasive cleaning agents (such as green scouring pads or other scourers) or polishing cleaning products (such as liquid scourers).

Never use caustic cleaning agents. These can cause stainless steel to discolour.

maintenance (continued)

removing/replacing grease filters

Remove the filters as follows: switch the fan and the lighting off.

Push the filter at the edge of the niche to the back and pull the front end down. You can now remove the filter from the hood.

The filter can only be put back into place in one way. Take note of the correct position of the filter (see illustration). Hold the filter in such a way that the covered part of the underside is at the centre rear. This is recognizable on the outside by the pattern with the smaller holes.

Put the filter back into place by first pushing the rear side into the holder. Then push the front upwards until it cannot go any further and let the filter slide forwards. The filter is now once again in place. Erase the electronic memory by pressing the button for approx. 5 seconds.

cleaning the grease filters

You can clean the grease filters in the dishwasher. Allow the filter to drain well - through the slits in the side - before putting it back.

replacing the carbon filter

Replace the carbon filter twice a year. This only applies to recirculation hoods. Put the carbon filter in the place intended for it above the filters. Erase the electronic memory by pressing the button for approx. 5 seconds.

some preliminary remarks

An extractor hood should be installed in accordance with national and local regulations. The minimum distance between the underside of the extractor hood and the hob should be 65~cm

The appliance should be connected by a registered fitter. Damage arising from incorrect connection or incorrect fitting is not covered by the guarantee.

attention:

When the extractor hood is incorrectly connected, extra air resistance occurs. This results in a decrease in suction capacity and the noise production of the extractor hood increases.

• Check the diameter of existing ducts, check for blockages and if they are not connected with other ducts or spaces
• Avoid constriction and angled bands, but instead use rounded curves for good air conducting.
• Use smooth ducts with the same internal diameter as the external diameter of the exhaust of the extractor hood.
• The use of flexible piping must be kept to a minimum and be used exclusively for making short bridging connections.

NB:

If an extractor hood and a heat source (for example, gas-, oil- or coal-fired cookers) which take air from the same room are in use at the same time, there is a possibility that the extractor hood will cause an underpressure in that room. The maximum permitted underpressure is 4Pa , so that no combustion gases from the heat source can find their way back into the room. For this reason, an air supply is required to provide a constant supply of fresh air to the room.

electrical connection

The extractor hood's plug should be accessible after fitting or the extractor hood should be isolated by a bipolar switch with 3mm plug pins.

When making the electrical connections, make sure that the socket is earthed and that the voltage and frequency correspond to the values given on the data plate.

If the connection cable is damaged, it should be replaced by the service department of the manufacturer or similarly qualified persons in order to prevent dangerous situations from arising.

installation (continued)

discharge

The discharge should not be connected to a duct which is also used for other purposes under any circumstances.

Bear in mind any local regulations concerning the ventilation of gas appliances.

The discharge may pass straight through the wall to the outside, provided that the wall opening is protected - by means of a grating - against rain, loaves, and the like getting in. The passage of the discharge may not be restricted by the wall grating by more than 20% .

We advise the use of as large a discharge duct as possible. A duct with a smaller diameter will have a low extraction capacity and produce higher noise levels.

Bends produce resistance. Make sure that the duct has a smooth run and has as few bends as possible. Draw the flexible pipe out as far as possible.

Before starting to drill, check that there are no installed pipes present.

The discharge stump has a diameter of 150mm . It is best if the discharge pipe also has this diameter.

A reducing piece (150 mm to 125 mm) is supplied with the appliance for connection to a 125 mm discharge pipe.

transport protection device

The cooker hood comes with a transport protection device that has to be removed before installation. Remove the 4 screws at the rear of the motor module (see fig.) and detach the motor modulo from the cooker hood. Observe the assembly instructions on the following pages.

assembly

building-in dimensions wall hood

WG3/4U

WS9011MM

WG3/4V

WS9011NM

WS1211NM

GB 13GB 12

assembly (continued)

installation wall hood

The most important dimensions are shown on the previous page. You can set the height of the telescopic pipe. Take the allowable tolerances into account. Position the discharge and the electrical connection in such a way that it will be easy to hook up the hood.

Remove the transport safety device prior to assembly, see page 12.

marking out and fitting fixing materials

Draw a vertical centre line on the wall (centre of the extractor hood).

Place the fastening clip against the wall so that it rests against the ceiling. The arrow on the flanged rim indicates the middle of the cooker hood. Mark the attachment holes to be drilled. Drill the holes (a 8 mm).

Put the plugs into the wall and fix the fixing bracket to the wall with the screws supplied (5 x 50 mm).

marking out and fitting motor module

Mark the position of the underside of the hood on the wall (bear in mind the minimum distance to the hohl). Mark the (vertical) centre line.

Fold or cut the template depending on type and mark the upper fixing holes.

Drill the fixing holes (2× 010mm)

Fix the plugs. Screw two nuts onto the threaded ends in the opposite direction. Screw the threaded ends into the wall leaving 20mm projecting (see illustration). Remove the nuts.

assembly (continued)

Suspend the motor module on the threaded ends (1). Screw the nuts on. Make sure that the motor module is exactly level.

Drill holes (2 x 0.6 mm) and secure the motor module with the fixing pins supplied (6 x 60) (2).

Fit the discharge duct.

Connect the motor module electrically.

fitting the hood

Fit the hood to the motor module. First hook the rear of the hood into the motor module at the bottom (1).

Then lift the front up (2) so that the two bolts supplied (M5 x 12) can be screwed in (3). Use these bolts to level the hood.

Use these screws to level the hood.

Make the plug connections in the hood.

assembly (continued)

fitting the telescopic pipe

NB: During recirculation, the ventilation slits must not be covered by the lower telescopic pipe.

Slide the flanged end of the upper telescopic pipe upwards between the fixing bracket and the wall, and slide the telescopic pipe against the ceiling. The telescopic pipe locks into position.

Hook the lower telescopic pipe onto the upper part and allow the lower part to drop so that it slides into the edge of the hood.

Put the filters in place and test the extractor hood.

technical data

type number: see data plate in the hood power supply: 230V - 50Hz

connected load: see data plate

dimensions (h x w x d): see "fitting dimensions"
approvals mark: Kema

This appliance complies with the CE directives.

external motors

NB: For appliances with an external motor, ATAG recommends the use of the following types of external motors:

WA11C5U WA300C5U

disposal of packaging and appliances

The packaging of the appliance is recyclable. It can be made up of:

-cardboard
polyethylene
CFC free polystyrene (PS rigid foam)
polypropylene straps around the box

Please dispose of these materials in a responsible way in accordance with the regulations of your local authority.

Your local authority will also be able to give you information about disposing disused household appliances in a responsible way.

préface

installation (suite)

evacuation

Installation (Forts.)

Abluftführung

WS8011MM WS1211MM
WS8011NM

DE 13DE 12

Montage (Forts.)

Einbau Wandmodel