BDSL300 - Lighting BLACK & DECKER - Free user manual and instructions
Find the device manual for free BDSL300 BLACK & DECKER in PDF.
User questions about BDSL300 BLACK & DECKER
0 question about this device. Answer the ones you know or ask your own.
Ask a new question about this device
Download the instructions for your Lighting in PDF format for free! Find your manual BDSL300 - BLACK & DECKER and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. BDSL300 by BLACK & DECKER.
USER MANUAL BDSL300 BLACK & DECKER
Your Black & Decker spotlight has been designed for providing illumination for home and leisure use. This product is intended for consumer use only.
Safety instructions
Warning! When using battery-powered appliances, basic safety precautions, including the following, should always be followed to reduce the risk of fire, leaking batteries, personal injury and material damage.
◆ Read all of this manual carefully before using the appliance.
The intended use is described in this manual. The use of any accessory or attachment or the performance of any operation with this appliance other than those recommended in this instruction manual may present a risk of personal injury.
◆ Retain this manual for future reference.
Using your appliance
Always take care when using the appliance.
- This appliance is not intended for use by young or infirm persons without supervision.
◆ The appliance is not to be used as a toy.
◆ Use in a dry location only. Do not allow the unit to become wet.
◆ Do not immerse the appliance in water.
Do not open body casing. There are no user-serviceable parts inside.
Do not operate the appliance in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.
◆ To reduce the risk of damage to plugs and cords never pull the cable to remove the plug from a socket outlet.
After use
When not in use, the appliance should be stored in a dry, well ventilated place out of the reach of children.
◆ Children should not have access to stored appliances.
When the appliance is stored or transported in a vehicle it should be placed in the boot or restrained to prevent movement following sudden changes in speed or direction.
◆ The appliance should be protected from direct sunlight, heat and moisture.
Inspection and repairs
Before use, check the appliance for damaged or defective parts. Check for breakage of parts, damage to switches and any other conditions that may affect its operation.
Do not use the appliance if any part is damaged or defective.
◆ Have any damaged or defective parts repaired or replaced by an authorised repair agent.
- Never attempt to remove or replace any parts other than those specified in this manual.
Specific safety instructions for spotlights
The following safety symbols are marked on your spotlight:
Warning! To reduce the risk of injury, the user must read the instruction manual.
Warning! Do not touch the lens as it becomes very hot during operation and remains hot for several minutes after the spotlight is switched off.
- Allow the spotlight to fully cool down before storage or charging.
- Keep combustible materials away from spotlight lens. Extreme heat can cause fires.
◆ Never place the light face-down on any surface when it is switched on or cooling.
Do not leave the spotlight unattended. Keep children and animals away from the work area. - Inspect the lens for damage following impact or if the spotlight is dropped. Do not operate without the lens in place or with a damaged lens.
The lens is manufactured from glass. The lens may crack or break if subject to an impact. If the lens is damaged it must be replaced by manufacturers original parts. Wear gloves as sharp edges may cause injury. - Never look directly into the light or shine the light into another person's eyes.
◆ Do not immerse spotlight in water.
Features
This appliance includes some or all of the following features:
- Quartz halogen bulb
- Hanging loop
- Trigger lock
- Pistol grip
- On/off trigger switch
- 12 Vdc power lead
- 12 Vdc accessory plug
- 12 Vdc battery clamps
Use
Power source requirements
The power source must provide 12 Vdc and must be able to supply the necessary current to operate the load.
ENGLISH
Warning! The spotlight must be connected only to batteries with a nominal output voltage of 12 volts.
The spotlight comes equipped with a 12 Vdc accessory plug (7) and/or battery clamps (8) for connection to a dc power source.
Always attach the connector end of the 12 Vdc battery clamp cable (8) to the 12 Vdc power lead (9) before attaching the battery clamps (8) onto the battery terminals.
Connecting to a power source using the 12 Vdc accessory plug (7)
◆ Make sure the spotlight is turned off, the trigger lock (3) is in the down position (locked) and that no flammable fumes are present in the area.
- Connect the spotlight to the power source by inserting the 12 Vdc accessory plug (7) firmly into the accessory outlet of a vehicle or other dc power source.
◆ Move the trigger lock (3) up to the unlocked position.
◆ Press the On/Off trigger switch (5) to turn the spotlight on.
◆ To lock the trigger switch (5) in the on position, press the trigger switch (5) and push the trigger lock (3) down.
◆ To shut the spotlight off, switch to the unlocked position and press the trigger.
Connecting to a power source using the cables
Use the cables and connect the appliance directly to the 12 Volt power source as follows:
Warning! Explosive gas may be vented from batteries when charging and under extreme conditions battery leakage may occur. Ensure the area is well ventilated when connecting the spotlight to a battery.
- Never allow the connector end of the 12 Vdc battery clamp cable (8) to touch the battery terminals. This could cause damage to the appliance and/or create a sparking/explosion hazard.
◆ Check the polarity of the battery terminals before connecting the spotlight.
Make sure the spotlight is turned off, the trigger lock (3) is in the down position (locked) and that no flammable fumes are present in the area.
- Connect the red battery clamp (8) to the positive terminal of the battery.
- Connect the black battery clamp (8) to the negative terminal of the battery.
◆ Make sure that all connections between the battery clamps (8) and the battery terminals are secure.
◆ Move the trigger lock (3) up to the unlocked position.
◆ Press the On/Off trigger switch (5) to turn the spotlight on.
◆ To lock the trigger switch (5) in the on position, press the trigger switch (5) and push the trigger lock (3) down.
◆ To shut the spotlight off, switch to the unlocked position and press the trigger.
Warning! Loose connectors may cause overheated wires and melted insulation.
Using the hanging loop
The hanging loop (2) may be used to hang the spotlight from a suitable location.
Warning! When using the hanging loop and the spotlight is turned on keep combustible materials away from the spotlight lens. Extreme heat can cause fires.
Maintenance
Your Black & Decker tool has been designed to operate over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance or cleaning on the appliance, unplug the appliance.
From time to time wipe the appliance with a damp cloth. Do not use any abrasive or solvent-based cleaner. Do not immerse the appliance in water.
Replacing the fuse in the vehicle dc accessory plug
◆ Remove the cap by turning it counter clockwise.
◆ Remove the centre pin and the spring.
◆ Remove the fuse.
◆ Fit a new fuse of the same type and size (8 A).
◆ Install the centre pin and spring.
◆ Tighten the cap by turning clockwise onto the plug.
Protecting the environment
Separate collection. This product must not be disposed of with normal household waste.
Should you find one day that your appliance needs replacement, or if it is of no further use to you, think of the protection of the environment. Black & Decker repair agents will accept old Black & Decker tools and ensure that they are disposed of in an environmentally safe way.
Separate collection of used products and packaging allows materials to be recycled and used again. Re-use of recycled materials helps prevent environmental pollution and reduces the demand for raw materials
Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or by the retailer when you purchase a new product.
ENGLISH
Black & Decker provides a facility for the collection and recycling of Black & Decker products once they have reached the end of their working life. To take advantage of this service please return your product to any authorised repair agent who will collect them on our behalf.
You can check the location of your nearest authorised repair agent by contacting your local Black & Decker office at the address indicated in this manual. Alternatively, a list of authorised Black & Decker repair agents and full details of our after-sales service and contacts are available on the Internet at: www.2helpU.com.
Technical data
| BDSL300 | |
| Input voltage Vdc 12 | |
| Unit weight kg 0.44 | |
| Bulb Type 12 V H3 25 W halogen | |
EC declaration of conformity
BDSL300 TYPE 1
Black & Decker declares that these products conform to:
Standards & Legislation.
EN60598, 2006/95/EEC
The undersigned is responsible for compilation of the technical file and makes this declaration on behalf of Black & Decker
Kevin Hewitt
Director of Consumer Engineering
Spennymoor, County Durham, DL16 6JG,
United Kingdom
08-08-2008
Guarantee
Black & Decker is confident of the quality of its products and offers an outstanding guarantee. This guarantee statement is in addition to and in no way prejudices your statutory rights. The guarantee is valid within the territories of the Member States of the European Union and the European Free Trade Area.
If a Black & Decker product becomes defective due to faulty materials, workmanship or lack of conformity, within 24 months from the date of purchase, Black & Decker guarantees to replace defective parts, repair products subjected to fair wear and tear or replace such products to make sure of the minimum inconvenience to the customer unless:
- The product has been used for trade, professional or hire purposes.
◆ The product has been subjected to misuse or neglect.
◆ The product has sustained damage through foreign objects, substances or accidents.
◆ Repairs have been attempted by persons other than authorised repair agents or Black & Decker service staff.
To claim on the guarantee, you will need to submit proof of purchase to the seller or an authorised repair agent. You can check the location of your nearest authorised repair agent by contacting your local Black & Decker office at the address indicated in this manual. Alternatively, a list of authorised Black & Decker repair agents and full details of our after-sales service and contacts are available on the Internet at:
www.2helpU.com
Please visit our website www.blackanddecker.co.uk to register your new Black & Decker product and to be kept up to date on new products and special offers. Further information on the Black & Decker brand and our range of products is available at www.blackanddecker.co.uk.
DEUTSCH
Director of Consumer Engineering
Spennymoor, County Durham, DL16 6JG,
Spennymoor, County Durham, DL16 6JG,
Royaume-Uni
08-08-2008
Garantie
Spennymoor, County Durham DL16 6JG,
Regno Unito
08-08-2008
Garanzia
EN/60598, 2006/95/EEG
Director of Consumer Engineering
Spennymoor, County Durham DL16 6JG,
Verenigd Koninkrijk
08-08-2008
Garantie
Spennymoor, County Durham, DL16 6JG,
Reino Unido
08-08-2008
Garantía
Spennymoor, County Durham, DL16 6JG,
Reino Unido
08-08-2008
Garantia
Director of Consumer Engineering
Spennymoor, County Durham, DL16 6JG,
Storbritannien
2008-08-08
Garanti
Spennymoor, County Durham, DL16 6JG,
Storbritannia
8.8.2008
Garanti
Black & Decker er trygg på kvaliteten til sine produkter og tilbyr en enestående garanti. Denne garantierklæringen kommer i tillegg til dine lovbestemte rettigheter, og er ikke i konflikt med disse. Garantien er gyldig i EU- og EFTA-medlemsstatene.
Director of Consumer Engineering
Spennymoor, County Durham, DL16 6JG,
Storbritannien
08-08-2008
Garanti
Director of Consumer Engineering
Spennymoor, County Durham, DL16 6JG,
Iso-Britannia
8.8.2008
Takuu
The following text in the source image is illegible due to extreme pixelation and distortion. No characters, words, or punctuation can be reliably identified. Therefore, no valid OCR text can be generated that matches the visual content of the source image.
Spennymoor, County Durham, DL16 6JG,
Ηνωμένο Βασίλειο
08-08-2008
